Cisco Switches :: SG 300 Command Line Setup?
Aug 13, 2011
Im trying to get my head around my new cisco SG 300 switch. I have used the Linksys SRW range before and configured it using teraterm and method described in the link below:
[URL]
As im fimilar with this method and the commands ideally I'd like to use this on the SG 300 range as well. Failing that, is it possible to use another method which uses the same commands which can be easily copy and pasted for setting up multiple switches with the configuration?
View 1 Replies
ADVERTISEMENT
Sep 20, 2012
we just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies
View Related
Oct 3, 2011
I am having some difficulties on finding information on how to setup two Cisco 1252 autonomous access points, via the command line. I am not having any luck finding steps on how to go about doing this and was curious if any one would be willing to give some insight. I am working on taking two of them setting one up as the root bridge and the other as non-root.
View 3 Replies
View Related
Apr 14, 2011
My grandma has a PC with Windows XP, she uses it only for Skype calls. can go in to her PC using command line from my PC? What commands should I use and what modifications to do on my grandma's PC? Should I ask permission from grandma's ISP (which is the same as mine)?
View 3 Replies
View Related
Mar 11, 2013
My 3550 is always 2 characters short on the command line. So my global configuration mode will look like this:Switch3550(config Say I wanted to enabled ftp, it would look like:Switch3550(config)# ftp enab.
View 2 Replies
View Related
Apr 22, 2013
I'm an ASDM 6.4 command line novice & I'm looking for the command to delete an unused vpn key, e.g. 'key1'.Or if there's a GUI method?
View 2 Replies
View Related
Oct 14, 2012
On my old 2511 access server, I could issue "clear line x" to close a session on an existing line.this doesn't seem to work on my new 2600XM with NM-16A access server (12.3(20)IOS), any command in newer IOS?
View 4 Replies
View Related
Jun 11, 2012
we just bought a 2921 with the following modules: 4 port clear channel T1/E1 HWICSM-ES3G-24-P: EtherSwitch.I read some CISCO documents, and not be able to find what I need. I would prefer all instructions from you are for CLI interface.This is my first time to deal directly with T1, WIC and 2921 etc. The following is what I get from ATT, IP masked IP Address Block IP Address: 20.20.20.136/29 WAN Link Details: WAN Link IP Address:13.13.13.92 AR Serial INT IP Address:13.13.13.93 CR Serial INT IP Address:13.13.13.94 WAN Link Subnet Mask:255.255.255.252
A: how do I configure T1, what does "AR, CR" stands for, and do I need to use both IP addresses? What is the WAN Link IP for?
B: We have two T1 lines, so I should plug them both to the WIC, say port 0 and port 1, how to configure them?
C: how do I access the firewall from the command line?
D: I followed T1/E1 HWIC installation guide, and as soon as I add channel-group to the controller t1, the serial interface went down?
View 2 Replies
View Related
Jul 13, 2011
command to get running config of Cisco VPN 3000 concentrator.
View 3 Replies
View Related
Jul 21, 2011
I want to telnet a router (say) 1.1.1.1 with usename "user" and password "pass" in command line. i tried using....telnet 1.1.1.1 -l user ..........but not working
View 3 Replies
View Related
Apr 15, 2012
12 users, 3 servers, 5 smartphones/tables on the WiFi (existing AP), future VPN server (maybe 5 simultaneous inbound VPN connections at the most with at least one client using a Mac), Cisco Gigabit small business switch.Internet access, VPN connectivity, and firewall (reporting, close/open ports for custom applications as needed)I was originally going to select an ASA5505-50 user device for the above client. The device is highly regarded on the Internet, offers a command line interface, priced right for the budget and should perform all duties required by the client.However, the addition of the RV180W to the Cisco product line has me questioning my choice.
1)Does the RV180W offer a command-line interface?
2)Is the RV180W limited in the number of users it can support without having to purchase additional user licenses?
3)How are firmware/software upgrades handled with the RV180W?
4)What will the client be giving up if they choose the RV180W vs. the ASA5505?
View 1 Replies
View Related
Dec 12, 2012
We have lots of new lap1041 need be set static IP Adress, hostname, Controller Adress via command line, but when use command (capwap ap hostname) to set hostname , always give us command disabled, we used command:clear capwap private-config, but it does not work, why?
View 4 Replies
View Related
Apr 30, 2012
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies
View Related
Feb 29, 2012
I want to know if WAG325N supports cisco's IOS so that i can configure it using command line interface? Is it possible?If not, how would i change ethernet interface speed setting so that it can support 100 mbps of speed. Because when i connect through LAN i'm always getting a full dulplex 10 mbps LAN connection automatically.
View 1 Replies
View Related
Apr 20, 2011
I have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies
View Related
Jan 6, 2012
how to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies
View Related
Dec 28, 2011
We have multiple computers (most Win7), game console, iPad,iPod etc on our network, networking was really never a problem.We switched a few weeks ago to mobile Internet, which uses the Netgear MBR1210 modem/router as network access point for all devices. All network users, except two or three, are wireless. Prior to getting the mobile Internet we were on Satellite ISP and used the Linksys 3200 router as access point/network router for our home network (behind the ISP modem).The Netgear modem/router is too far away from my work area in the home, things like my printer, a desktop tower need to be plugged into a router because they are not wireless. The plan is to have the netgear router set up just as a modem/server, turn the wireless off on it, pull one network cable to my Linksys 3200 and use the Linksys as network access point for all devices. Which settings do I have to have on each router to do this? Where do I plug the network cable in between the routers? Do I go from a Lan port on the Netgear to the Wan port on the Linksys?
Which IP settings do I specify? How do I turn the automatic configuration of the Linksys off? Needless to say, I'm a bit lost here. I had contacted a Netgear forum prior, they gave me a little picture on how everything should be hooked up and the settings, but the Linksys router just did not want to work with these settings at all. Secondly, because of all this screwing around with the settings of the Linksys.I uninstalled the cisco connect program for the linksys and removed the original network we had with the linksys. Now the program refuses to install again, cisco connect that is.
View 2 Replies
View Related
May 24, 2013
setting up MPLS on a single T3 line. A client has contacted us to set up a 2951 at a branch location. There are 5 locations connected with MPLS.They will split off 4meg of the T3 for mpls. The rest of the 45meg would go to the internet.They have two 1841's currently set up with a T1 line in each. One 1841 connects to the MPLS and the other to the internet.When the T3 is turned up by the provider, everything, internet and MPLS, will go through it. I asked for the current configurations, but I have not received them yet and this setup is due in a couple days.Given I've never configured MPLS before and I have a rudimentary understanding of how it works, any tips or configurations? I'd hate to be stuck on site and not equipped to complete the job.
View 3 Replies
View Related
Nov 26, 2012
I'm trying to set up a command set in Cisco ACS 5.3, I can't get i to work no mather who I try What I'm trying to accomplish is that some users, say Bob can run every priv. level 1 command + show run, or just to specify which commands Bob will be able to run, whatever is easiest to set up.
In my switch I have the commands:
aaa new-model
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization commands 1 default group tacacs+
aaa authorization commands 15 default group tacacs+ <--- tried diffrent apporaches whith priv level..
(and specied a tacacs server)
is the "default" under "aaa authorization commands 1x default group tacacs+" the name of the command set?
In the ACS I have specied a Authorization group and binded it to the command set, should the user have priv 15 for this to work or priv 1?(I have also specied a user and an identity group and specied ip ranges under "Network Devices and AAA Clients")
View 2 Replies
View Related
Nov 12, 2012
configure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies
View Related
Feb 7, 2011
I have a building with 30+ pc's, printers and cameras. I do not have a "server" setup, however I want them to be connected to the T1 line comming into the building for internet as well as file sharing, etc.Currently, I have the T1 line connecting to as Linksys E3000 wireless router. From there I have a cable connected to the wireless router (it has 4 ports also) and then going to a Netgear FS524 (24 Port 10/100 MBPS Fast Ethernet Switch) via port number 24. I then have another CAT5 cable connected to a port on this switch, extending to a D-Link DES-1024D (another 24 Port, 10/100 switch)I then have the 30+ CAT5 cable coming into all three of said devices... No then, I get Internet connection on all units, the problem is that I cannot see all of the devices.
View 2 Replies
View Related
May 24, 2013
we have a new ISE 3315 installation going on, I powered on the Appliance and appliance booted sucessfully, I run the Setup command. however after Setup is completed and appliance got a reload, it is not booting at all , booting seems to be hang up as per the snapshot attached.however Appliance is pingable, . i carried the following tasks as part of troubleshooting.
2: suspecting that Setup was corrupted, i then re-initialzied / re-installed the ISE Completely, then i run the setup command and after self reload, exactly same behaviour.
3: I tried with both Secure CRT & Putty and results are same
View 2 Replies
View Related
Aug 8, 2012
I was trying to setup a Nexus (5596 running NX-OS 5.1(3)N2(1)) to use the "ip ospf name-lookup"command that I am using on IOS-based routers. Unfortunately this command does not appear to be supported on NX-OS and I cannot find a replacement.Is this another feature that's left out of NX-OS?
View 4 Replies
View Related
Nov 9, 2012
I have blown the dust of my Cisco 1801 and looked the books out to put a decent router on my network now I am running my own server however I have hit a few bumps but totally stick now.
DHCP is disabled and I can't remember the sub net. Connected with the console cable but finding my admin password isn't accepted. Running the password recovery but unable to access ROMMON using special command > break. I should get this but the ATA monitor library just loads and I get stuck on the password screen.
*** System received an abort due to Break Key *** signal= 0x3, code= 0x500, context= 0x813ac158 PC = 0x802d0b60, Vector = 0x500, SP = 0x80006030 rommon 1 > #
From what I gather (still green behind the ears) the ROMMON command has been disabled. Any way to get into my Cisco or do I need to reload the IOS on the flash card?
Here is my event log/putty output
Event log
2012-11-09 19:59:47 Opening serial device COM6
2012-11-09 19:59:47 Configuring baud rate 9600
2012-11-09 19:59:47 Configuring 8 data bits
[code]......
View 4 Replies
View Related
Oct 29, 2012
I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
View 4 Replies
View Related
Apr 16, 2012
I'm finding some odd information from Cisco pages and non-Cisco pages also. What is the correct syntax for specifying boot images on a flash:/ of a switch? The differences is if you need the "/" or not as well as after the ";" fo you need to specify flash again.
View 2 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Oct 13, 2011
About a week ago I changed over 9 HP Procurve switches that were previously stacking in series (yeah, daisy-chain) to a Access-Distribution type scenario with 2 (or 4 on server switches) Gb ports on each switch Trunked together connecting to a central full 48x Gb switch.
During this I updated firmwares on all the switches (most still on their shipped 5-8 year old versions) to the latest stable release (and in the process found out that HP switch firmware is absolutely brutal and untested - See ProCurve 2510G FW 11.16 as an example) .
I saw vast improvements across the network immediately after the change (wow, really? 9 48-port switches effectively sharing a single 1Gb line to the servers and internet was a bit slow? Don't tell my co-workers, they don't think that's possible ) .
The only thing that I didn't see an improvement in was on some Linux and BSD servers, which would top out at 11MB/s doing a SMB (SAMBA) transfer. These are managed systems part of our business system, but we still need to be able to pull local backups for ourselves. So I contacted our vendor. The vendor confirmed that the line speed is showing as 1000T-FDx (same as the switch is showing).
Vendor is now claiming that after these changes were put in place, the speed on their servers (and their servers ONLY) was reduced to a maximum of 5MB/s (~60Mb/s?) doing rsync transfers between themselves. And they are all on the same 2510 (48 port all 10/100/1000), which makes absolutely no sense whatsoever to me. Furthermore this is on the ONLY switch on the entire network that had an updated firmware already installed - that's not even a possibility here.
I put some windows servers on that switch and can get 60MB/s+ all day (SMB transfers). I've also tried from their one server that I can access to doing an rsync or scp to another BSD box, and max out at 15MB/s (with 100% CPU usage on the test box - I'm assuming the decryption is pretty heavy?)There is absolutely no QoS, limiting, or any possibility of throttling the links the servers are on the switch. There are no excessive broadcasts saturating it, and the ports and cables test fine.
View 15 Replies
View Related
Jan 29, 2011
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies
View Related
Feb 5, 2012
I am trouble shooting a SF 200-48P and I am a bit lost without a CLI not used to the GUI. What I need to know is how to add the IP address helper command to the switch?I have a number of IP phones which are not getting an IP address from DHCP (PCs which are diasy chained off the phones are all working correctly). On the higher end switches I would have added the IP address helper command to the VLAN and that would have sorted it. How to do this on the small business switch.
View 2 Replies
View Related
Feb 8, 2013
What does "ip routing" do on the CLI on the SG300? When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it. I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
View 2 Replies
View Related
Aug 25, 2011
Previously srw2008 switches are used, now Cisco sg300-10 models was obtained. It does not work with ctrl-Z command to enter the local Config (lcli). What is the correct command?
View 2 Replies
View Related
Oct 10, 2012
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies
View Related
