Cisco WAN :: 2801 - Configure Router To Use One Primary Line
Feb 21, 2012
simple configuration of a 2801 Router. I have 2 internet providers with static ip's connected to F0/0 and F0/1 and one Vlan for LAN area. I would like to configure the router to use one primary line and just in case to use the back-up line. [code]
Now if detects that it hasn't cable link on the FastEthernet interfaces it's working. I'm using 2 wireless gateways to acces the internet each one connected on the 2 FaEth for simulating the providers. If i simulate an issue on the provider ( i've removed the sim from the wireless gateway) it doesn't pass on the second isp.I haved trying to configure with "IP Service Level Agreements " for failover / load balancing but the command "ip sla" is incomplete. I can't make an update of the IOS because the customer do not have an Service Contract with Cisco.
View 15 Replies
ADVERTISEMENT
Feb 14, 2011
How to configure to use Router with Lease Line ?
1.connect a computer to the wan port-router
2.give the ip in the url-------- 192.168.1.1( by default )
3.enter username and passwrd
4. then in the GUI mode
5. go to the wan setting ...router
6.there put the live ip and the gateway and the dns....aircel detail....
7.go the lan setting and put the lan ip series do nt configure dhcp go manually to all the nodes and put the lan ip u have 4 lan ports
8.out of 4 port ...port 1-- connect the dialler...in lan port
9.and in port 2 connect to (switch) a unmanaged switch frm where u can connect to your lan
10.if in the lan setting u hv given the ip 192.168.1.1
11.then put ur dialler ip 192.168.1.2
12. and local lan machine will tk the ip frm 3 onwards
13.nw if u want to authenticate ur dialer in our voip gateway then give the ip of ur router
15. 192.168.0.1 will be the ip of the lan setting in the router
16. and this will act as a gater to ur local machine gateway
View 1 Replies
View Related
Apr 30, 2012
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies
View Related
Jan 10, 2008
Is it possible to configure two AG241 adsl routers back to back via two wire line as a Lan to Lan network?
View 8 Replies
View Related
Jan 5, 2012
Is it possible to configure a Cisco 2801 router with Multipoint Port Channeling? A service provider dropped a 4.5Mbps ( 3x T1s ) to one of our customers without any equipment. They assume the CPE responsible. If so, any links to documentation on this configuration. If not, what device will they need to buy from Cisco that can bundle these 3 T1s together then feed it into their router?
View 6 Replies
View Related
Sep 12, 2012
I am getting little confuse about the configuration of my second WLC .I have a project going on with main office and 10 sites . I have placed my primary WLC 5508 with software 6.0 and all the branches i deployed ap . I put all the AP in Hreap mode did VLAN MAPPING . And i Created Groups based on the location and i put this AP's insde those group .All the sites seems perfectly working. Now I have to place my sedcond WLC in one another branch . I did all the initial configuration of my 2nd WLC .
But am worried if my primary wlc fail how could it can be taken to second WLC . And if i put inside wireless--> hight avaliabilty--primary ip and secondary ip .Again do i need to configure those WLAN , AP GROUPS , everythink in this WLC sepretely or any option . If i need to create the group do i need to select the ap's which already added to primary wlc groups.
View 1 Replies
View Related
Jun 19, 2012
We are trying to configure vrf aware GET VPN with COOP having primary and secondary key servers and also 3 GM routers. All GM routers we use are Cisco 888 and Key servers we use cisco 2911 routers. All GMs crypto maps have been applied into Vlan interface as there's no L3 interface on 888 routers.
Always members can form a tunnel with primary KS, we have configured redundancy with secondary key server and listed on each GM primary and secondary KS on GDOI group.
The issue we facing is that whenever we shutdown the primary or secondary servers the tunnel is not forming with available KS unless otherwise we mannually clear the crypto session. In another way when primary KS down it doest not fall back to secondary KS and no GM get registered. We have already played with all the timers such as DPD, SA lifetimes, GDOI rekey lifetime etc and also exchanging the keys (import/export) with KS and COOPs but there's no luck. We could see the following message was seen on both KS.
[code] 192.168.1.3 is the primary KS and 192.168.1.6 is the secondary KS.I captured attached debug output from 1 GM and secondary KS while I shutdonw the primary KS and also attached is our senario we were trying get work.
Also attached is the show output from both KSs when it form a tunnel with GM.
View 2 Replies
View Related
Dec 18, 2010
I state that I'm very fast Voip router configurations, the problem is as follows: I need to configure a SPA3102 so that I hijack a line RTG via LAN / WAN or on a SPA2102 in the motion that the 2102 can receive and make calls.
View 4 Replies
View Related
Nov 12, 2012
configure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies
View Related
Dec 7, 2011
Is it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
View 2 Replies
View Related
Nov 3, 2011
I previously put this is the 'Video over IP' discussions group, which is not getting any response.I have a 6509 and need to configure QoS on gig line cards that have 1P3Q8T queue structure. I've already got the mls qos configured, and have the correct class maps built for Voice, Video, and Signalling.(I'm not doing autoqos). I have only four classes; voice, video, signalling, and default (best effort).I need to configure the commands on the individual gig ports for the appropriate bandwidths as shown below:
1. 300 VoIP G711 calls x 100kbs/call = 30mbs of priority queue DSCP = EF (46) CoS = 5
2. 150 Video conference calls x 1.5mbs/call = 225mbs DSCP = CS4 (32) CoS = 4
3. 450 Signalling x 13kps/call = 5.8mbs (round to 6mbs) DSCP = CS3 (24) CoS = 3
4. Default class is not marked DSCP & CoS = 0
View 1 Replies
View Related
Jun 11, 2012
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
View 2 Replies
View Related
Oct 10, 2012
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies
View Related
Jul 23, 2007
I looked but could not find any information on what's the use of the USB interface on my 2801 router. I saw something about Cisco USB memory module and eToken by Aladdin. Is this interface restricted to Cisco and Aladdin only?
View 17 Replies
View Related
Aug 4, 2011
I have a Cisco RV110W small business router setup at my home. It has one of those HTML GUI interfaces, check the boxes, etc.., to get things working. Basically, your typical home router with VPN. I have enabled the VPN, it's PPTP, added the password, and now it's automagically configured! I can successfully VPN to my home with a Windows7 client. Here's my problem, I now need to VPN into my home router with a 2801. Is this possible? Everything I found on the subject has only been to setup a Cisco IOS router as a VPN server or tunneling to another IOS router. No examples using an IOS based router as the client.
View 3 Replies
View Related
May 29, 2012
We have one Router Cisco 2801 at the customer site and facing issue of having very High CPU coming to 99%.CPU utilization for five seconds: 99%/28%; one minute: 99%; five minutes: 98%
View 2 Replies
View Related
May 31, 2011
I'm having trouble setting up a Cisco 2801 as an internet router between our firewall & our ISP.I've setup FastEthernet0/0 as the WAN port & FastEthernet0/1 as the LAN port. I've setup a default gateway pointing the next hop (the ISP),when I plug in a pair of laptops configured to mimic our IP scheme, I'm able to ping thru, but when I put the router between our firewall & ISP I'm not able to get out to the internet (can't ping google) I can still ping the next hop.,Our old router died, so I am unable to pull up its configuration. Here is the code I'm come up with so far.
View 6 Replies
View Related
Dec 26, 2012
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to an offshore network.
View 2 Replies
View Related
Jan 27, 2013
I have to configure failover on both router. if one get fail then the other router should be dial.Physical connection
•1. Two routers (Cisco 2801) are connecting with splitter through RJ 11 port.
•2.Only one ISP link is coming in splitter.
Requirement: As per as customer requirement. He wants redundancy with in both 2 routers. If one goes down then the other router come up. And same configuration on 2801_R2 router. I am planing to do HSRP on our lan network (2801R1,2801R2 ehternet interface which connected to switch). from switch i will create two default route with (next hope) virtual ip address.
View 6 Replies
View Related
Mar 7, 2011
I have a 2801 router with a HWIC-3G-cdma card that I have inherited from a predicessor. How to use a cellular card on a router and need to get this thing up and running. Any example config that I can see or point me in the right dorection to get this up and running? I have the cellular card set up as Cellular0/1/0 on the interface, I assume that that was done by default, and it has an IP address. The Static Route of 0.0.0.0 0.0.0.0 Cellular0/1/0, in the config with only 2 other interfaces as being direct connection. But that is as far as I recognize. Do I need to set up a router protocol? Which one? How do I use the cellular card? Do I need to have an ISP connection?
View 1 Replies
View Related
Mar 20, 2012
I have just received Time Warner Cable and get 16Mbps down from them directly through their modem (motorola DOCSIS 2.0 modem- SB5101) to my PC (using speedtest.net). When I then connect TWC's modem through my 2801 router on fa0/0, the download rate I get is considerably slower (on the order of 3-4Mbps via same testing method). What am I missing?
Here is how the passthrough interface is setup:
interface FastEthernet0/0
bandwidth receive inherit
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
I have attempted removing bandwidth command - nothing changed with it not there. I have also hard coded the speed and duplex to 100/full to no avail....
Other possible relevant configs:
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 dhcp
access-list 1 permit 192.168.1.0 0.0.0.255
Basically this things is wide open... for testing but the download speed differential is perplexing to me.
View 10 Replies
View Related
Dec 26, 2012
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to our overseas office.
Our side uses the 1841 router and our provider has set-up our E1 connection to be via Serial interface while on our overseas office uses the 2801 and will connect via the T1 card, which by the way does not have any serial interface ports just ethernets.
So far checking on how to configure this, I am unsure on how the connection will happen since the info that I got is that T1 does not have the option to hold an IP address (also unsure on this though). With this in mind and that the 2801 does not have serial interfaces, does that mean that IPL connection would be via the available Ethernet ports?
View 11 Replies
View Related
Apr 9, 2013
I want to block access of some clients from the vlan1 to acces internet blocking their MAC address. How can i do this?
I have tring this way:
access-list 700 deny mac address 0000.0000.0000
access-list 700 permit 0000.0000.0000 ffff.ffff.ffff
int fa00
bridge-group 1 {input-address-list 700 output-address-list 700}
but it's not working .
View 1 Replies
View Related
May 10, 2011
I have 5 routers. Four routers are: c2801-IPBASEK9-m v 12.4(24)T2. One router is a C2800-IPBASEK9-M v 12.4(24)T3. so, it appears that the IOS on all 5 routers is very similar, the only difference is the T3 at the end of the version and that 4 are 2801s and one is a 2800. What is very wierd is the 4 2801 have the embedded scripting language "tclsh". The 2800 does not have tclsh. If I issue the command: tclsh on the 2800, I get:
Center-GW#tclshTranslating "tclsh"
% Bad IP address or host name% Unknown command or computer name, or unable to find computer addressCenter-GW#
View 1 Replies
View Related
Apr 12, 2011
I have problems with the Router 2801.When i give the command show processes cpu, the command show me that the router is working in 98%.
I have vlans like voice vlan and others, I have one 20 Mb Wan Link and I redirect all traffic from my lan to this link and when i browse in internet or i do downloads the router goes to 98%, when i don't make it the router processes goes down.
I thought be problem with hardware, but i exchange to another router and the same problem happened.Before this situation, I had one link with 12 Mb and nothing happened, when i exchange this to the 20 mb link the problems starting.
View 3 Replies
View Related
Feb 7, 2012
I have one problem doing a ping to a router lan interface, I have 3 routers (2801) connected between each other (separated 1 mile each), the link is established trough microwave signals (connected to the 2801 fast ethernet interfaces), every router has a connection to a LAN. One of them is located at headquarters.Last thursday I replace one of the router with a cisco 2901, i configure the router with the same configuration that was on the 2801, i power up the router and the 2 link were up without problems.One day after the noc called me to tell me that after i replace the router they can't ping the router IP lan interface on the new 2901 (before the replacement the ping was sucessful). I called one user the lan connected to that 2901, and they can do a ping to the router's LAN IP address.
I can ping the 2901 IP wan interfaces, I can ping the LAN users ip address, but i cannot ping the router LAN IP address, from my desktop, and neither the 2 routers 2801 connected to the 2901.I show the configuration on the 2901, I couldn't change it because i didn't have time to do that, but i'll change the configuration to use ipsec tunnels.The configuration as you can see, has a crypto map, but the acl used by the crypto map, only permits the interfaces ip address, so i think that doesn't work, so the traffic doesn't get encrypted, but i don't know if that is the problem why i can't do a ping to the lan interface. [code]
View 5 Replies
View Related
Feb 28, 2012
I'm using for a company network a 2801 Cisco Router. This router has 2 FastEthernet Interfaces connected on 2 ISP's and one VLAN for internal users. What acl should i use if for example one client from the lan is using a torrent client to download from the internet. I want just to specify a maximum download speed or to block that client to access the internet when it's trying to download something that can affect other clients from the LAN.
View 2 Replies
View Related
May 3, 2011
I have problems with router 2801, the version is
Cisco IOS Software, 2801 Software (C2801-ADVENTERPRISEK9-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)
When i start a download the processes of the router cpu stay in 99%/97%. When i'm not doing a download the processes stay in 3%/0%. I have one 20 mb link to Wan.
I did the troubleshooting seeing the this document :
[URL]
View 8 Replies
View Related
Feb 11, 2013
Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 5 Replies
View Related
Jun 18, 2012
The HWIC-2CE1T1-PRI card isn't supported on a CISCO2801 router
View 7 Replies
View Related
Feb 9, 2012
The goal is to add a 2801 router between a DSL modem and a switch and obviously still access the internet. I connected and configured as explained below and the results are:
- I am able to ping internet addresses from the 2801 router
- I am not able to ping internet addresses from userlaptop but I am able to ping LAN gateway (192.168.254.254)
I cannot understand why the internet requests from the user laptopuser are not routed to the internet but the router itself can access the internet.
INTERNET====DSLmodem=====CISCO2801=====unmanagedSwitch=====userlaptop
DSLmodem:
non-bridged mode and does the PPPOe authentication.
WAN interface: Dynamic IP address assigned by ISP
[Code].....
View 14 Replies
View Related
Mar 29, 2011
I have setup an eBGP session to a Cisco 2801 CE router. The BGP session establish, however, the session keeps resetting after 90 sec which is the BGP keepalive holdtime value.
On the PE router I found that the OutQ doesn't clear = 22 when doing a "sh ip bgp x.x.x.x summary" - Session reset at 1:30.When I filter the amount of routes advertized to the CE neighbor with the "neighbor x.x.x.x prefix-list out" - I see the OutQ clear = 0 and the BGP session remains up.
-Number of NRLI advertized without prefix filter = 172
-Number of NLRI after filter = 52
why the OutQ doesn't clear.
View 1 Replies
View Related
Apr 25, 2011
I have been having problems when trying to host servers on games, etc.I have 2 routers. A modem router, which is a Thomson router. That is the main one. It has a wire connecting from it, to a D-Link router that is near my Computer, and my brother's one. Then that D-Link router has 2 wires from each port, to mine, and my brother's computer.So, I am trying to host games.I didn't connect to the Thomson one, which is also wireless. I am connected to the wired one (D-Link). When I try to host while connected to it, my brother, and other people can't find the server. My brother and me can find it on LAN, but not Internet.But when I disconnect from the Wired, and connect to the Thomson wireless one, and then when I host, I can find it on INTERNET. Even my brother can. He can connect to it perfectly.
I do not want to connect to the wireless, because then it will cause lag spikes every 5 minutes.So, when I disconnect from the wireless, and connect to the wire, I went into the CMD, and typed in ipconfig. I found out that the Default Gteway is the D-Link IP.When I connect to the wireless, and disconnect the wired, I went into CMD, and then the Default Gateway is the Thomson one, which is the main router.So what I want to do, is use the D-Link router, and that router will have the same IP as my thomson one, so that I can host perfectly with no lag spikes, and using a wired connection.
View 19 Replies
View Related
