I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to an offshore network.
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to our overseas office.
Our side uses the 1841 router and our provider has set-up our E1 connection to be via Serial interface while on our overseas office uses the 2801 and will connect via the T1 card, which by the way does not have any serial interface ports just ethernets.
So far checking on how to configure this, I am unsure on how the connection will happen since the info that I got is that T1 does not have the option to hold an IP address (also unsure on this though). With this in mind and that the 2801 does not have serial interfaces, does that mean that IPL connection would be via the available Ethernet ports?
I've been looking and I can really find much info about this, I got a 1841 and 2801 router with ADSL WIC cards and both are synching really low compared to my cheap home router
This leads me to believe I need a firmware update so I got the adsl_alc_20190.bin and loaded it into flash and reloaded my router but its still saying my firmware is using an embedded one.
sh flash:-#- --length-- -----date/time------ path1 1000636 Oct 4 2011 05:59:54 +00:00 adsl_alc_20190.bin
sh dsl interface atm0/1/0ATM0/1/0Alcatel 20166/20174 chipset information ATU-R
[Code].....
I have a cisco 2801 router and I want to connect two ADSL links on it and balance the load but not that kind of IOS that team would need
View 2 Replies View RelatedI have got two 1841 and one 881 cisco router. I can keep any one of this router at HO and remaining at branch office. I have got a static internet IP at HO but dynamic IP at branch office. I want to setup a VPN to connect to HO from branch office through router. The branch connects through a private IP for internet purpose. Which VPN is the most secure and best for this purpose.
View 1 Replies View RelatedI have the following devices for our IT Test LAB
1. Cisco 1841 with 2 Fast Ethernet interfaces fa0/0 & fa0/1
2. Cisco 2960-S
3. Speedstream 6200 DSL Modem ( PPOE Connection with Static IP address)
I want to connect to the internet using the current DSL connection we currently have .
LAPTOP --> SWITCH 2960 --> ROUTER 1841 ---> DSL Modem ---> ISP
Troubleshooting 1: Currently from the LAPTOP i am able to ping
1. Switch 2960 Vlan interfaces
2. Router 1841 fa0/0 & fa0/1
BUT can not Ping the DSL Modem LAN interface IP 192.168.2.1 and can not get out to the INTERNET
Troubleshooting 2:currently from the Switch 2960 i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1 interfaces
3. Laptop A & B
But can NOT ping the DSL modem LAN interface IP 192.168.2.1 and can not get out to the internet
Troubleshooting 3:Currently from the Cisco 1841 router i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1
3. Laptop A & Laptop B
4. Can Get out to the internet. I am able to ping any internet destinations without any problem
I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies View RelatedI looked but could not find any information on what's the use of the USB interface on my 2801 router. I saw something about Cisco USB memory module and eToken by Aladdin. Is this interface restricted to Cisco and Aladdin only?
View 17 Replies View RelatedI have a Cisco RV110W small business router setup at my home. It has one of those HTML GUI interfaces, check the boxes, etc.., to get things working. Basically, your typical home router with VPN. I have enabled the VPN, it's PPTP, added the password, and now it's automagically configured! I can successfully VPN to my home with a Windows7 client. Here's my problem, I now need to VPN into my home router with a 2801. Is this possible? Everything I found on the subject has only been to setup a Cisco IOS router as a VPN server or tunneling to another IOS router. No examples using an IOS based router as the client.
View 3 Replies View RelatedWe have one Router Cisco 2801 at the customer site and facing issue of having very High CPU coming to 99%.CPU utilization for five seconds: 99%/28%; one minute: 99%; five minutes: 98%
View 2 Replies View RelatedI'm having trouble setting up a Cisco 2801 as an internet router between our firewall & our ISP.I've setup FastEthernet0/0 as the WAN port & FastEthernet0/1 as the LAN port. I've setup a default gateway pointing the next hop (the ISP),when I plug in a pair of laptops configured to mimic our IP scheme, I'm able to ping thru, but when I put the router between our firewall & ISP I'm not able to get out to the internet (can't ping google) I can still ping the next hop.,Our old router died, so I am unable to pull up its configuration. Here is the code I'm come up with so far.
View 6 Replies View RelatedI have to configure failover on both router. if one get fail then the other router should be dial.Physical connection
•1. Two routers (Cisco 2801) are connecting with splitter through RJ 11 port.
•2.Only one ISP link is coming in splitter.
Requirement: As per as customer requirement. He wants redundancy with in both 2 routers. If one goes down then the other router come up. And same configuration on 2801_R2 router. I am planing to do HSRP on our lan network (2801R1,2801R2 ehternet interface which connected to switch). from switch i will create two default route with (next hope) virtual ip address.
I have a 2801 router with a HWIC-3G-cdma card that I have inherited from a predicessor. How to use a cellular card on a router and need to get this thing up and running. Any example config that I can see or point me in the right dorection to get this up and running? I have the cellular card set up as Cellular0/1/0 on the interface, I assume that that was done by default, and it has an IP address. The Static Route of 0.0.0.0 0.0.0.0 Cellular0/1/0, in the config with only 2 other interfaces as being direct connection. But that is as far as I recognize. Do I need to set up a router protocol? Which one? How do I use the cellular card? Do I need to have an ISP connection?
View 1 Replies View RelatedI have just received Time Warner Cable and get 16Mbps down from them directly through their modem (motorola DOCSIS 2.0 modem- SB5101) to my PC (using speedtest.net). When I then connect TWC's modem through my 2801 router on fa0/0, the download rate I get is considerably slower (on the order of 3-4Mbps via same testing method). What am I missing?
Here is how the passthrough interface is setup:
interface FastEthernet0/0
bandwidth receive inherit
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
I have attempted removing bandwidth command - nothing changed with it not there. I have also hard coded the speed and duplex to 100/full to no avail....
Other possible relevant configs:
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 dhcp
access-list 1 permit 192.168.1.0 0.0.0.255
Basically this things is wide open... for testing but the download speed differential is perplexing to me.
I want to block access of some clients from the vlan1 to acces internet blocking their MAC address. How can i do this?
I have tring this way:
access-list 700 deny mac address 0000.0000.0000
access-list 700 permit 0000.0000.0000 ffff.ffff.ffff
int fa00
bridge-group 1 {input-address-list 700 output-address-list 700}
but it's not working .
I have 5 routers. Four routers are: c2801-IPBASEK9-m v 12.4(24)T2. One router is a C2800-IPBASEK9-M v 12.4(24)T3. so, it appears that the IOS on all 5 routers is very similar, the only difference is the T3 at the end of the version and that 4 are 2801s and one is a 2800. What is very wierd is the 4 2801 have the embedded scripting language "tclsh". The 2800 does not have tclsh. If I issue the command: tclsh on the 2800, I get:
Center-GW#tclshTranslating "tclsh"
% Bad IP address or host name% Unknown command or computer name, or unable to find computer addressCenter-GW#
I have problems with the Router 2801.When i give the command show processes cpu, the command show me that the router is working in 98%.
I have vlans like voice vlan and others, I have one 20 Mb Wan Link and I redirect all traffic from my lan to this link and when i browse in internet or i do downloads the router goes to 98%, when i don't make it the router processes goes down.
I thought be problem with hardware, but i exchange to another router and the same problem happened.Before this situation, I had one link with 12 Mb and nothing happened, when i exchange this to the 20 mb link the problems starting.
I have one problem doing a ping to a router lan interface, I have 3 routers (2801) connected between each other (separated 1 mile each), the link is established trough microwave signals (connected to the 2801 fast ethernet interfaces), every router has a connection to a LAN. One of them is located at headquarters.Last thursday I replace one of the router with a cisco 2901, i configure the router with the same configuration that was on the 2801, i power up the router and the 2 link were up without problems.One day after the noc called me to tell me that after i replace the router they can't ping the router IP lan interface on the new 2901 (before the replacement the ping was sucessful). I called one user the lan connected to that 2901, and they can do a ping to the router's LAN IP address.
I can ping the 2901 IP wan interfaces, I can ping the LAN users ip address, but i cannot ping the router LAN IP address, from my desktop, and neither the 2 routers 2801 connected to the 2901.I show the configuration on the 2901, I couldn't change it because i didn't have time to do that, but i'll change the configuration to use ipsec tunnels.The configuration as you can see, has a crypto map, but the acl used by the crypto map, only permits the interfaces ip address, so i think that doesn't work, so the traffic doesn't get encrypted, but i don't know if that is the problem why i can't do a ping to the lan interface. [code]
I'm using for a company network a 2801 Cisco Router. This router has 2 FastEthernet Interfaces connected on 2 ISP's and one VLAN for internal users. What acl should i use if for example one client from the lan is using a torrent client to download from the internet. I want just to specify a maximum download speed or to block that client to access the internet when it's trying to download something that can affect other clients from the LAN.
View 2 Replies View RelatedI have problems with router 2801, the version is
Cisco IOS Software, 2801 Software (C2801-ADVENTERPRISEK9-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)
When i start a download the processes of the router cpu stay in 99%/97%. When i'm not doing a download the processes stay in 3%/0%. I have one 20 mb link to Wan.
I did the troubleshooting seeing the this document :
[URL]
Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
The HWIC-2CE1T1-PRI card isn't supported on a CISCO2801 router
View 7 Replies View RelatedThe goal is to add a 2801 router between a DSL modem and a switch and obviously still access the internet. I connected and configured as explained below and the results are:
- I am able to ping internet addresses from the 2801 router
- I am not able to ping internet addresses from userlaptop but I am able to ping LAN gateway (192.168.254.254)
I cannot understand why the internet requests from the user laptopuser are not routed to the internet but the router itself can access the internet.
INTERNET====DSLmodem=====CISCO2801=====unmanagedSwitch=====userlaptop
DSLmodem:
non-bridged mode and does the PPPOe authentication.
WAN interface: Dynamic IP address assigned by ISP
[Code].....
simple configuration of a 2801 Router. I have 2 internet providers with static ip's connected to F0/0 and F0/1 and one Vlan for LAN area. I would like to configure the router to use one primary line and just in case to use the back-up line. [code]
Now if detects that it hasn't cable link on the FastEthernet interfaces it's working. I'm using 2 wireless gateways to acces the internet each one connected on the 2 FaEth for simulating the providers. If i simulate an issue on the provider ( i've removed the sim from the wireless gateway) it doesn't pass on the second isp.I haved trying to configure with "IP Service Level Agreements " for failover / load balancing but the command "ip sla" is incomplete. I can't make an update of the IOS because the customer do not have an Service Contract with Cisco.
I have setup an eBGP session to a Cisco 2801 CE router. The BGP session establish, however, the session keeps resetting after 90 sec which is the BGP keepalive holdtime value.
On the PE router I found that the OutQ doesn't clear = 22 when doing a "sh ip bgp x.x.x.x summary" - Session reset at 1:30.When I filter the amount of routes advertized to the CE neighbor with the "neighbor x.x.x.x prefix-list out" - I see the OutQ clear = 0 and the BGP session remains up.
-Number of NRLI advertized without prefix filter = 172
-Number of NLRI after filter = 52
why the OutQ doesn't clear.
We have a cisco 2801 router in class which has a disabled password recovery. We tried almost everything, we cannot get into ROMmon and the break sequence doesn't work in any program (hyper terminal, putty, teraterm pro).
Here is the log from hyperterminal:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL].Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 131072 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabledReadonly ROMMON initializedPASSWORD RECOVERY FUNCTIONALITY IS DISABLEDprogram load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xd49718Self decompressing the image :
[code].....
I have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies View RelatedI was just recently hired in my company, we have an sf300-24p switch but I cant find the console cable for it, I think it needs a female to female db9 serial cable, all I have is a DB9 serial to rj45 console cable for the 2801 router, also I cant find the IP address of the sf300 switch, it is directly connected to the 2801 router, I issued a show arp to the router but didnt find the switch's IP add for web access, to sum it up I have no way of configuring the switch, is there any way to find the IP address of the switch? It also dosnt show on show cdp neighbors?
View 13 Replies View RelatedWe have recently implemented some QoS on our routers and i have noticed that the CPU usage has risen enormously as a result.
I checked the CPU Processes and found that the avg values are 50% usage. This seems rather high considering that only 75% of our edge routers have this feature enabled.
Our main router is a Cisco CISCO2911/K9 (revision 1.0) with 487424K/36864K bytes of memory. Our edge routers are either 2801 models or 881 models.
This is our first implementation of QoS and would like to ensure that it is working properly before implementing other QoS rules. Here is a copy of the config on the 2911 router:
class-map match-all Citrix
match protocol citrix
class-map match-all Print
match protocol printer
class-map match-all C-Coolingata
[ code]......
Here is the config on our edge routers:
class-map match-any Citrix
match access-group name Citrix-ACL
[code]....
As you can see we have different link speeds at different sites based on their size, location etc. How to be able to confirm that this config is correct?
Currently we have a cisco router 2801 for Wireless Internet connection. And we are going to have another ISP that can provide us Fibre Optic internet connection rather than wireless.My question is that can we use this router for fibre optic internet connection? how do we go about this? what is the maximum bandwidth that the router can support?
View 8 Replies View RelatedI am trying to install Radius server for a cisco 2801 router. I am not able to configure it properly.
View 2 Replies View RelatedWe have a Cisco 2801 router running IOS "c2801-spservicesk9-mz.151-4.M4.bin" which we upgraded from previous “c2801-spservicesk9-mz.124-3d.bin”.
Requirement.
We want to monitor the device temperature via snmp but unable to do because temperature ratings are not available on "show environment all" output like below.
Routeri# sh environment all Fan 1 OK Fan 2 OK ILP Power Supply - Absent Fan Speed Setting: Normal
Where as on Cisco 2811/51 & Cisco 3825/45 we can get temperature ratings on "show env all" output.
As per link [URL] below commands are supported on Cisco 2800 series router.
Command options
• show environment all
• show environment fans
• show environment leds
• show environment power-supply
• show environment table
• show environment temperatures
• show environment voltages
I want to know whether this is Cisco 2801 platform limitations or something else. tried to find Cisco doc on this but no luck.
I have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801