Cisco WAN :: 2801 - Connect Two ADSL Links On It?
Feb 2, 2012I have a cisco 2801 router and I want to connect two ADSL links on it and balance the load but not that kind of IOS that team would need
View 2 Replies
ADVERTISEMENT
Cisco WAN :: 2811 Router - ADSL Links
Jul 18, 2012can a Cisco 2811 router bundle 2 or 4 ADSL lines ? Reason am asking, we need a device that would be able to bundle 2 or 4 ADSL lines from ISP so that we can you it as backup link in-case the company Internet link does down.
View 5 Replies View RelatedCisco Switching/Routing :: 2800 Series - Dual ADSL Links?
Jan 31, 2012In a site we currently have 1 BT provided ADSL link which is currently terminated using their device which I believe is some kind of 2wire device, which is extremely slow due to distance from the Exchange (4Mbps)...We have a growing number of users here and want to install a second ADSL line from BT to give them increased performance.
We have a Cisco 2800 sat not doing much so I was wondering if I could use this to load balance the link? I know BT do not support MPPP so therefore the maximum any user can get will be the speed of a single link (4Mbps)...But basically how can this be done..
Can I leave the two BT routers in place and place the Cisco 2800 behind them, or do I need to purchase two ADSL modules for the 2800 and terminate the connection there?Also once done, what do I need to do regarding actually setting up the load balancing? I have seen this:
[URL]
But am unsure as to how relevant it is? I am not sure I understand what the ACL's are being used for? I just want all users on the LAN to load balance out...
Also I am unsure of this statement:You potentially need to add policy-based routing for specific traffic to ensure that it always uses one ISP connection. Examples of traffic that require this behavior include IPSec VPN clients, VoIP handsets, and any other traffic that use only one of the ISP-connection options to prefer the same IP address, higher speed, or lower latency on the connection.I do not understand why a established session such as a VPN client, would ever traverse the second ISP connection anyway?
Cisco WAN :: Connect Multiple Links To PIX 515?
Oct 12, 2011We have a site to site VPN from one client location to our production center in offshore. At the client side we have a PIX 515 used for the tunnel. Since the client requires a backup VPN over a different ISP we will have to add the ISP to the same PIX and then create the secondary VPN.
how we can acheive two ISP's on one PIX since only two Ethernet ports are availble.
PIX Details:
Cisco PIX IOS 7.2(2)
PIX-515E, 128 MB RAM
Cisco WAN :: 2921 - Connect 2 ISP Links Into One Gigabit-interface On Router?
Oct 6, 2012I want to connect 2 ISP links into one Gigabit-interface on my Router 2921, can any one tell me how to do that ? sub-interface creation is not possible on cisco 2921
View 1 Replies View RelatedCisco :: How To Connect 2801 Router To 1841
Dec 26, 2012I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to an offshore network.
Cisco Switching/Routing :: Connect Nexus 2000 To Two 5000 With Different Links?
Feb 12, 2013is it possible to connect one Cisco Nexus 2000 fabric extender to two Cisco Nexus 5000 and use one link on the first side and two links on the other side?
View 3 Replies View RelatedCisco Switching/Routing :: 2801 Cannot Connect With Console Cable
Jun 12, 2013I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies View RelatedCisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?
Aug 24, 2012i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedConnect Dir 615 With Adsl Modem?
Jan 27, 2011recently i got a dlink dir 615 router from a friend. i'm using adsl modem now. i want to connect the modem to the router so that i have a wireless at home for my laptop and iphone. i have follow the step in the router manual but it did not work. i just cannot conect to the router page through the 192.168.0.1 i am using windows vista home basic.
View 15 Replies View RelatedProcess To Connect Two ADSL Routers?
Feb 23, 2012Tell me the process to connect TWO ADSL Router
View 1 Replies View RelatedCisco WAN :: 1900 Router With Adsl Wic Won't Connect To Internet
Oct 17, 2011if I have made a simple mistake with my config. It has authenticated ok and been assinged an Internet IP address from the ISP but the clients can not connect ping any internet address nor can the router.
hostname
!boot-start-markerboot-end-marker!!enable secret 5 $1$WGr1$khNrjiwYANhUsIaKEBDsL0enable password 7 121A0C041104!no aaa
[Code].....
Cisco WAN :: Unable To Connect 887VA Router To ISP Via ADSL
Jul 7, 2011I have been trying to connect a new Cisco 887VA Router to the Internet using ADSL via PPPoE and have been unsuccessful. The DSL line is active and functioning correctly since the current "old" router is connected and working without any problems (the "old" DLink router is connected to an Alcatel DSL Modem). AT&T provides the ADSL service to the office. When the Cisco Router is connected it tries to negotiate a connection via PPPoE on the WAN interface but utlimately fails. The IP for the WAN interface is dynamic.
Below is the current configuration of the router.
!
! Last configuration change at 00:43:54 UTC Sun Jun 26 2011
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
Broadband :: Connect 2 ADSL Routers On 1 BT Line?
Feb 19, 2011Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
View 2 Replies View RelatedRouters / Switches :: Connect 2 Adsl Devices Together?
Mar 1, 2011A Telindus 1421 SHDSL Router and a Sagem F@st 1500WG wireless adsl router.The question is: Can i connect this two devices directly over the adsl port and share networks on each side of each of the devices?
View 3 Replies View RelatedConnect A Wireless Modem To Adsl For Wifi?
Jan 15, 2013I wanna Know That I hab a nokia siemens SL2_141 modem which is not in use...beacause I dont have anymore BSNL connection. Now I am using A Wireless Modem of MTS. Recently I have Buyed New Phone I wanna Use wifi...
HOw Can I connect Internet of my Wireless Modem to The Wifi of nokia siemens SL2_141 Modem.I have Attached A photo So that U ppl Understand properly.
Linksys Cable / DSL :: X3000 Cannot Connect To ADSL
Dec 12, 2011I just bought a Linksys X3000 to work with my ADSL connection (provider is Singtel from Singapore). I managed to use Cisco connection application to logon and setup the router OK, yesterday. I even connected my PC to the router by LAN, and also a few devices wirelessly.At the end of the day, I switched off everything... but next morning, when I booted up the router, I found that all my devices cannot access internet. Upon checking the server (192.168.1.1), I found that it does not have a IP from Singtel, although on the router the internet symbol (globe sign) is lighted up.I rebooted the router twice, getting the same results (note: I waited for a long time each time, until the globe was lighted up).I disconnected the X3000, and reconnected my Netgear DGN2000. It worked (and retrieved an IP address from Singtel). I then disconnected the Netgear and reconnected X3000. To my surprise, this time X3000 got the IP address and then internet is working again.
View 9 Replies View RelatedCisco WAN :: SR520-ADSL-K9 - Can't Even Connect To Router After Power Failures
Aug 6, 2012I'am a bit newbie at using Cisco products and here is my problem : I have set up a VPN tunnel between 2 Sites (A and B) a few month ago using 2 cisco SR520-ADSL-K9. All was working fine until power failures occured on the sites B (secondary site).
What happened was that none of the ethernet ports were working, excepting during booting, I was then able to ping computers linked to ports Fastethernet0, FastEthernet1, FastEthernet2 and FastEthernet3 but after a few seconds all ports were disabled but my DSL seemed to be working.
So I took back the router home to check it. I managed (I think) to make a factory reset using a serial terminal and following the procedure described here [URL]
Since I did the reset, I thought I would be able to re-use Cisco Configuration Assistant (3.1) to re-configure the router (I am very bad at using the command lines) but I am unable to connect to the router using the supposed default IP : 92.168.75.1 (I set my computer to use 192.168.75.50 IP adress with mask 255.255.255.0). But I can't connect to the router ... even if the Ethernet ports seem to work because green light is on when plugging my cable. connect to my router using CCA ?
For more information, here is what I get when I run "show startup-config" and "show running-config" in terminal console. I guess the objective is to make the startup-config beeing the running-config, but I have no idea on how to do that ..
show startup-config
show running-config
Router#show startup-config
[Code]......
Cisco Routers :: Total Failure To Get SR520-ADSL-K9 To Connect To ISP
Dec 15, 2011We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.
Servers :: How To Connect A Adsl Modem To A Computer Network
Jun 19, 2011how to connect a adsl modem to a computer network using a switch with a server.I have a network with a server and about ten clients computers all connected through a switch, the server has an IP 192.168.1.1 as its gateway. I want to connect adsl modem to the switch so that all the computers can have access to the net, but the adsl too has 192.168.1.1 as its IP.
View 1 Replies View RelatedRouters / Switches :: To Connect ADSL Direct To Computer
Dec 2, 2012I have CentOS and the application I am running does not listen on 192.168.1.5 (Private IP address). Right now I have connected using bridge mode and I can see in my network configuration-> ppp and eth0. PPP has public IP and eth0 has private IP. Is there any way that I can get public ip assigned to eth0? I do not have Static IP, I want to use the public dynamic IP assigned by my ISP to use in eth0 interface.
View 2 Replies View RelatedUse ADSL Wireless Router (one With RJ11 WAN In) To Connect To Cable Net?
Aug 26, 2012Is it possible to use ADSL Wireless router (one with RJ11 WAN in) to connect to cable net? If not is there any which can allow me to connect to cable net in future if in case I change to cable net ISP.
View 2 Replies View RelatedRouters / Switches :: How To Connect ADSL And 3G Router On Network
Aug 7, 2012I have one ADSL router that I have configured Port Forwarding on it, but the internet is very slow. I also have another 3G router and I want to use it for internet because it is much faster, but it cannot do Port Forwarding. How can I connect this two routers in one network such that ADSL router is for Port Forwarding only and 3G router is for internet only?
View 1 Replies View RelatedHow To Connect TPLink Adsl With Belkin Wireless Router
Jan 13, 2013I hav bsnl broadband connection in my home.... I connected a tplink wired for browsing...I also have a belkin wireless router..... I connected those routers.... And only wired communication is possible
View 7 Replies View RelatedLinksys Cable / DSL :: WAG120 - Connect Two ADSL Routers?
Feb 14, 2012I was using Linksys ADSL router ( WAG120) as modem router. Recently I bought new Linksys x3000 and installed a modem router in place of WAG120. Now i would like to connect the both routers to get the signals in first floor of my house.
View 9 Replies View RelatedCisco :: How To Connect A Catalyst 2960 Switch To A Zyxel ADSL Modem
Jul 19, 2012I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
Cisco Firewall :: How To Connect ASA5505 Behind ISP Netgear DG834 ADSL Router
Jan 30, 2010I am a beginner to ASA. I am trying to connect the ASA 5505 behind the netgear ADSL router which is getting dynamic IP address from the ISP. How to configure the ASA5505 outside interface for SSL VPN connectivity?
View 8 Replies View RelatedCisco WAN :: How To Connect Catalyst 2960 Switch To Zyxel ADSL Modem
Jul 18, 2012I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
Why Can't Embarq 660R ADSL Router Connect To Belkin N300
Oct 16, 2012I have a Embarq 660 Series modem, but i wanted wifi. so i bought a belkin N300 wireless router this morning. And it won't connect to internet. I'm sure i've plug the cable in the right spot. And the EQ 660R ADSL router/modem is working. The belkin package came with a CD, and it's the setup program for the wireless router. but as it tried to form a connection, it said failed to connect to the modem. so does this means embarq 660 series isn't compatible with Belkin N300?
View 3 Replies View RelatedDlink Adsl-2640t Doesn't Connect Wirelessly To Cable Net
Jan 10, 2011dlink adsl-2460t which is really torturing. I ahve connnected my cable net modem to my router but unfortunately its of no use cos i cant connect my laptop to it. Although it shows the availablity of the connection but it doesn't get through to net..it keeps on giving a caution sign on the bottom right corner, above the signal strength...
View 1 Replies View RelatedConnect Cat6 Cable From Ext Nte To ADSL Nexuslink 5631 Router?
Feb 28, 2013I am trying to connect a cat 6 cable from the Ext Nte to the adsl nexuslink 5631 router but i couldn't make the router works for the 2 line i only get one line led on i tried to change the wires colors on the rj11 (4 pins) and even so i cloud not get both led light goes on for tho line and this only for the cat 6 if i hook the old wire i dont know whats kind of wire i think its for inercom or mebe cat3 its works in the ext Bt only 2 wires connected and on the modem side 4 wires is o nthe rj11 plug i tried to do it the same way with cat6 i only get single line and i do it now with (white-orange=pin 1) (blue-white=pin 2) (white-blue=pin 3) (orange-white=pin 4 ) on the plug , on the bt side i tried to but white -blue with blue-white not working even the opposite.i just want to know how to wire from ext-Bt to router using rj11-4pin cua thats what my router use on bonding to lines, btw i have only 2 wire on the bt side because i got 2 line phones on a phone line in the bt?
View 5 Replies View RelatedCisco WAN :: Connect Four ADSL Lines To 1841 (Backup) And Work In Load Balancing Way
Dec 17, 2011We have a cisco 1941 with line t1 Symmetric, (Also have Cisco 1841 unused, but works) I would like to connect the Cisco 1841 to four Adsl Backup lines in case the T1 or the Main cisco 1941 go down I know a BGP is needed on our ISP site,
How can i connect four Adsl lines to The cisco 1841 (Backup) and make them work in a Load Balancing way.
Routers / Switches :: Connect Win98 To ADSl Modem Over The Network Switch?
Apr 19, 2012Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
View 2 Replies View Related
