Cisco WAN :: 2801 Router Not Showing Temperature In Show Environment All
Jun 19, 2012
We have a Cisco 2801 router running IOS "c2801-spservicesk9-mz.151-4.M4.bin" which we upgraded from previous “c2801-spservicesk9-mz.124-3d.bin”.
Requirement.
We want to monitor the device temperature via snmp but unable to do because temperature ratings are not available on "show environment all" output like below.
Routeri# sh environment all Fan 1 OK Fan 2 OK ILP Power Supply - Absent Fan Speed Setting: Normal
Where as on Cisco 2811/51 & Cisco 3825/45 we can get temperature ratings on "show env all" output.
As per link [URL] below commands are supported on Cisco 2800 series router.
Command options
• show environment all
• show environment fans
• show environment leds
• show environment power-supply
• show environment table
• show environment temperatures
• show environment voltages
I want to know whether this is Cisco 2801 platform limitations or something else. tried to find Cisco doc on this but no luck.
View 2 Replies
ADVERTISEMENT
Jun 19, 2012
Is temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies
View Related
Nov 4, 2011
I have a peachtree application installed on a standalone system and needs three other systems to connect to the shared folder to work but each time I click on show workgroup computers, it shows me a blank page on one and only shows the other system on the other.Hence when i try to connect to the peachtree folder, it give error that the system is not accessible?
View 1 Replies
View Related
Oct 8, 2009
i have an Issue with my cisco 2801.in the logs shown me the interface FE0/0 cames up some times but never show the down state, I receive my internet service on this interface but never lost the conection, just this logs information
Oct 7 18:39:32.412: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 7 18:39:41.448: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 7 21:57:20.775: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 8 02:29:31.350: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 8 02:55:12.362: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
[code].....
the IOS Version that is running is
flash:c2801-adventerprisek9-mz.124-24.T1.bin
View 4 Replies
View Related
Jun 11, 2012
I have Cisco 2801 router with IP Base image, i have upgraded its image into advance Ip services for using IP SLA features but after upgradation HWIC card not showing in configuration.
When i recall IP base image then configuration show presence of HWIC card but with advance IP services HWIC card not showing.
View 8 Replies
View Related
Apr 14, 2012
For an assignment in a class I am taking I created a simple network using GNS3 and set up static routing. Everything works fine, I can ping all of the hosts. One of the questions I am supposed to fill out is what happens when I use the "show ip route" and "show ip protocols" commands. When I use "show ip route" I get what seems to be the correct output. However when I use the "show ip protocols" command nothing happens. No output, no error, no nothing. It just goes right back to the prompt. This happens exactly the same on both routers in my network. incase it matters the router is c3640.
PS. would the output be non-existent because I have not set up any ip protocols. In a similar assignment I set up rip and when I used "show ip protocols" i did get what appeared to be the correct output. However I didn't write it down and when I put in the command again about an hour later after I took a break I also did not get an output until I re-entered the rip related commands.
View 2 Replies
View Related
May 1, 2012
I notice that show inventory not showing all members in a 3750-stack after we merged two stacks. Its only showing the master of the new stack, and the previous master of the old stack.
View 3 Replies
View Related
Nov 8, 2012
I am trying to find out what the 'normal' operating temperature of the CPU in a 3945 router is? We have just replaced some 2800 routers for 3945's and the NMS server initially complained about the new router CPU temperature being too high. Compared to the 2800 the CPU temperature is much hotter - 50 degrees celcius as opposed to 20-smothing degrees. I have searched but can't find what are considered 'normal'?
This is the output:
router#sho environment allSYSTEM POWER SUPPLY STATUS==========================Internal Power Supply 1 Type: DCInternal Power Supply 1 12V Output Status: Normal
[Code].....
View 3 Replies
View Related
Feb 9, 2012
how do I monitor temperature of my 1921 router? Which commands do I need to put on router and which MIBs to use. I am using PRTG network monitor as a monitoring system.
View 10 Replies
View Related
Jul 11, 2011
I cant remember where I read it but when I noticed that my HDD was running hot even when it was meant to be idle, I read that the router causes the storage device to run at full spin regardless.
I was wondering, do we know if that issue is fixed with this latest firmware update (June 14th)? I've had it on for about 10minutes but I'm not sure how long it takes to get to the temp that it was running at before.
View 4 Replies
View Related
Jan 12, 2011
Yesterday I installed my new E3000 router. After an hour I noticed that de temperature of the bottom was very high and it stil is . Is that normal?
View 7 Replies
View Related
May 3, 2012
My company has a single 2811 WAN router with dual uplilnks to different ISPs right now. Recently we have had a major hardware failure issue that resulted in network outage. My manager reconsidered my recommendation of dual WAN routers but told me we had limited budget so could only afford one new router.
So now we are looking at solution of 2811 + 2911 with same license level. We don't have any special feature, just basic routing, basic BGP and static routes. I need to know what the implication of having different WAN router model is.
View 6 Replies
View Related
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
Jan 29, 2012
How to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Jun 18, 2011
I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies
View Related
Jul 23, 2007
I looked but could not find any information on what's the use of the USB interface on my 2801 router. I saw something about Cisco USB memory module and eToken by Aladdin. Is this interface restricted to Cisco and Aladdin only?
View 17 Replies
View Related
Aug 4, 2011
I have a Cisco RV110W small business router setup at my home. It has one of those HTML GUI interfaces, check the boxes, etc.., to get things working. Basically, your typical home router with VPN. I have enabled the VPN, it's PPTP, added the password, and now it's automagically configured! I can successfully VPN to my home with a Windows7 client. Here's my problem, I now need to VPN into my home router with a 2801. Is this possible? Everything I found on the subject has only been to setup a Cisco IOS router as a VPN server or tunneling to another IOS router. No examples using an IOS based router as the client.
View 3 Replies
View Related
May 29, 2012
We have one Router Cisco 2801 at the customer site and facing issue of having very High CPU coming to 99%.CPU utilization for five seconds: 99%/28%; one minute: 99%; five minutes: 98%
View 2 Replies
View Related
May 31, 2011
I'm having trouble setting up a Cisco 2801 as an internet router between our firewall & our ISP.I've setup FastEthernet0/0 as the WAN port & FastEthernet0/1 as the LAN port. I've setup a default gateway pointing the next hop (the ISP),when I plug in a pair of laptops configured to mimic our IP scheme, I'm able to ping thru, but when I put the router between our firewall & ISP I'm not able to get out to the internet (can't ping google) I can still ping the next hop.,Our old router died, so I am unable to pull up its configuration. Here is the code I'm come up with so far.
View 6 Replies
View Related
Dec 26, 2012
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to an offshore network.
View 2 Replies
View Related
Jan 27, 2013
I have to configure failover on both router. if one get fail then the other router should be dial.Physical connection
•1. Two routers (Cisco 2801) are connecting with splitter through RJ 11 port.
•2.Only one ISP link is coming in splitter.
Requirement: As per as customer requirement. He wants redundancy with in both 2 routers. If one goes down then the other router come up. And same configuration on 2801_R2 router. I am planing to do HSRP on our lan network (2801R1,2801R2 ehternet interface which connected to switch). from switch i will create two default route with (next hope) virtual ip address.
View 6 Replies
View Related
Mar 7, 2011
I have a 2801 router with a HWIC-3G-cdma card that I have inherited from a predicessor. How to use a cellular card on a router and need to get this thing up and running. Any example config that I can see or point me in the right dorection to get this up and running? I have the cellular card set up as Cellular0/1/0 on the interface, I assume that that was done by default, and it has an IP address. The Static Route of 0.0.0.0 0.0.0.0 Cellular0/1/0, in the config with only 2 other interfaces as being direct connection. But that is as far as I recognize. Do I need to set up a router protocol? Which one? How do I use the cellular card? Do I need to have an ISP connection?
View 1 Replies
View Related
Mar 20, 2012
I have just received Time Warner Cable and get 16Mbps down from them directly through their modem (motorola DOCSIS 2.0 modem- SB5101) to my PC (using speedtest.net). When I then connect TWC's modem through my 2801 router on fa0/0, the download rate I get is considerably slower (on the order of 3-4Mbps via same testing method). What am I missing?
Here is how the passthrough interface is setup:
interface FastEthernet0/0
bandwidth receive inherit
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
I have attempted removing bandwidth command - nothing changed with it not there. I have also hard coded the speed and duplex to 100/full to no avail....
Other possible relevant configs:
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 dhcp
access-list 1 permit 192.168.1.0 0.0.0.255
Basically this things is wide open... for testing but the download speed differential is perplexing to me.
View 10 Replies
View Related
Dec 26, 2012
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to our overseas office.
Our side uses the 1841 router and our provider has set-up our E1 connection to be via Serial interface while on our overseas office uses the 2801 and will connect via the T1 card, which by the way does not have any serial interface ports just ethernets.
So far checking on how to configure this, I am unsure on how the connection will happen since the info that I got is that T1 does not have the option to hold an IP address (also unsure on this though). With this in mind and that the 2801 does not have serial interfaces, does that mean that IPL connection would be via the available Ethernet ports?
View 11 Replies
View Related
Apr 9, 2013
I want to block access of some clients from the vlan1 to acces internet blocking their MAC address. How can i do this?
I have tring this way:
access-list 700 deny mac address 0000.0000.0000
access-list 700 permit 0000.0000.0000 ffff.ffff.ffff
int fa00
bridge-group 1 {input-address-list 700 output-address-list 700}
but it's not working .
View 1 Replies
View Related
May 10, 2011
I have 5 routers. Four routers are: c2801-IPBASEK9-m v 12.4(24)T2. One router is a C2800-IPBASEK9-M v 12.4(24)T3. so, it appears that the IOS on all 5 routers is very similar, the only difference is the T3 at the end of the version and that 4 are 2801s and one is a 2800. What is very wierd is the 4 2801 have the embedded scripting language "tclsh". The 2800 does not have tclsh. If I issue the command: tclsh on the 2800, I get:
Center-GW#tclshTranslating "tclsh"
% Bad IP address or host name% Unknown command or computer name, or unable to find computer addressCenter-GW#
View 1 Replies
View Related
Apr 12, 2011
I have problems with the Router 2801.When i give the command show processes cpu, the command show me that the router is working in 98%.
I have vlans like voice vlan and others, I have one 20 Mb Wan Link and I redirect all traffic from my lan to this link and when i browse in internet or i do downloads the router goes to 98%, when i don't make it the router processes goes down.
I thought be problem with hardware, but i exchange to another router and the same problem happened.Before this situation, I had one link with 12 Mb and nothing happened, when i exchange this to the 20 mb link the problems starting.
View 3 Replies
View Related
Feb 7, 2012
I have one problem doing a ping to a router lan interface, I have 3 routers (2801) connected between each other (separated 1 mile each), the link is established trough microwave signals (connected to the 2801 fast ethernet interfaces), every router has a connection to a LAN. One of them is located at headquarters.Last thursday I replace one of the router with a cisco 2901, i configure the router with the same configuration that was on the 2801, i power up the router and the 2 link were up without problems.One day after the noc called me to tell me that after i replace the router they can't ping the router IP lan interface on the new 2901 (before the replacement the ping was sucessful). I called one user the lan connected to that 2901, and they can do a ping to the router's LAN IP address.
I can ping the 2901 IP wan interfaces, I can ping the LAN users ip address, but i cannot ping the router LAN IP address, from my desktop, and neither the 2 routers 2801 connected to the 2901.I show the configuration on the 2901, I couldn't change it because i didn't have time to do that, but i'll change the configuration to use ipsec tunnels.The configuration as you can see, has a crypto map, but the acl used by the crypto map, only permits the interfaces ip address, so i think that doesn't work, so the traffic doesn't get encrypted, but i don't know if that is the problem why i can't do a ping to the lan interface. [code]
View 5 Replies
View Related
Sep 17, 2012
if there is a MIB for monitoring temperature on a Cisco 800?
View 2 Replies
View Related
Feb 5, 2011
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies
View Related
Feb 28, 2012
I'm using for a company network a 2801 Cisco Router. This router has 2 FastEthernet Interfaces connected on 2 ISP's and one VLAN for internal users. What acl should i use if for example one client from the lan is using a torrent client to download from the internet. I want just to specify a maximum download speed or to block that client to access the internet when it's trying to download something that can affect other clients from the LAN.
View 2 Replies
View Related
May 3, 2011
I have problems with router 2801, the version is
Cisco IOS Software, 2801 Software (C2801-ADVENTERPRISEK9-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)
When i start a download the processes of the router cpu stay in 99%/97%. When i'm not doing a download the processes stay in 3%/0%. I have one 20 mb link to Wan.
I did the troubleshooting seeing the this document :
[URL]
View 8 Replies
View Related
