Cisco :: BRI Card Does Not Show In (show Voice Port)
Jun 18, 2011I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3750 - Show Interface Vlan (ID) Doesn't Show In / Out Traffic Rate
Mar 13, 2013I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedCisco :: Understand Show Sessions And Show Connection Commands?
Jan 29, 2012How to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedCisco Switching/Routing :: 2960 Don't Display Logging Trap Informational In Show Running / Show Startup
May 27, 2012Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedD-Link / DCS-942L :: No Files Show Up On Card Management Screen
Feb 10, 2013Ive formatted the sd card, enabled video/image recording, but no files show up on the sd management screen. I tried to select a folder to save the files to from the live video screen, but nothing pops up/opens when I click on the folder button. I'm using the google chrome browser w the latest java update on an xp box.
View 4 Replies View RelatedCisco Switching/Routing :: 3845 With HWIC-2FE / Card Fails To Show Up
Jan 16, 2008I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
Windows Firewall - Can't Get Any Port To Show As Open
Apr 26, 2012I have done any and everything just to even open a specific port on my pc and try PortForward's port checker and web based checkers, and I can't get the port or any port to show as open.I am trying to make an IP webcam on my network viewable from the internet.My setup is like this"gigaset 204a" / DSL modem (Ethernet cable goes into internet port on LINKSYS WRTGS wireless router) [code] Disabled I went to LINKSYS port forwarding, the address I am forwarding to is the ip webcam server. I know if the IP changes it won't work, but before thinking of setting up a static ip for the webcam on my network, I need to get it to actually work.Nothing I do will open any ports on my pc. I've tried enabling DMZ. I've even set rules for windows firewall to allow incoming/outgoing connections on the port I want, i've disabled windows firewall. am running on windows 7 ultimate. The problem for my really is as far as I can tell, I can't even open a port to allow connections to my computer from the outside. Of course all my internet games etc work fine and have never had a problem, but I can't seem to manually open a port I want.
View 4 Replies View RelatedCisco Switching/Routing :: 4500 How To Show Last Time A Port Was Active
Jun 28, 2012is there a way to show the last time a port was active/inactive on a catalyst 4500?
View 3 Replies View RelatedCisco Switching/Routing :: 6500 - Show Platform Port-asic Stats Drop Command?
Feb 21, 2012On a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies View RelatedToshiba Laptop With Window 7 - The LAN Port On Laptop Does Not Show A Light When The Cable Is Plugged In?
Jun 30, 2011TOSHIBA LAPTOP WITH WINDOW 7 - The LAN port on my laptop does not show a light when the cable is plugged in?
View 1 Replies View RelatedCisco :: ASA 8.3 With ASDM 6.3 Show Log On ACL?
Jan 20, 2011I am trying to see what traffic goes through a certain ACL so I specify a protocol instead of allow all IP traffic. So what I did is enabled logging with debugging on that ACL. When I right click on the ACL and show log, nothing shows up. But I see hits on the ACL.
View 1 Replies View RelatedCisco :: Devices Don't Show In NCS 1.0
Sep 15, 2011I've added several switches and one WLC to my new NCS Prime box. I don't see them in the display. If I try to readd one, it says it already exists. What am I missing?
View 0 Replies View RelatedCisco :: Show Dynamic PAT Table?
Nov 6, 2012Trying to get a Cisco ASA 5505 to show me all the current dynamic PAT. (I don't want to see hard-coded port forwarding, just dynamic stuff the router is doing to allow various hosts on the network to talk to the WAN.)
View 8 Replies View RelatedCisco WAN :: Show Ip Route On 1841?
Dec 13, 2010We have a Cisco 1841 router and checked something an unnusual (never seen before) routing table having L - local routes. if this an IOS bug or same as C - connected local routes.
1841#sh verCisco IOS Software,
1841 Software (C1841-IPBASE-M),
Version 15.0(1)M3, RELEASE SOFTWARE (fc2)Technical Support: [URL] ... Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Sun 18-Jul-10 01:16 by prod_rel_team
[Code] .....
Cisco WAN :: Show All Module On ASR 1004?
Feb 14, 2012how to show all the module on the ASR 1004?
View 4 Replies View RelatedCisco :: 5508 WLC Show Configuration
Nov 19, 2011I would like to know whether there is any command that shows the configuration of the wireless controller (5508) like when you upload the configuration file from the GUI of the WLC. In other words, I don't want to show me all the verbose running configuration as the "show running-config", but a brief configuration as for example described below: [code]
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.3 Show Two Mac Addresses
Apr 16, 2012I have a solution of thre ACS.. one primary and two secondaries. My customer report me that in port of the switch where is connected the ACS show two mac address. [code]
View 1 Replies View RelatedCisco WAN :: Show Modules In ASR1006?
Feb 15, 2012In a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
View 1 Replies View RelatedIP Configuration Command Won't Show WAN IP
Apr 16, 2011i have ADSL. modem:Meganet when i connect to internet from windows xp with making PPPOE connection everything is fine and when i do ipconfig i can see my IP. but when i connect directly from router then IPconfig show this only:
[code]...
Wireless :: Why Does Neighbor's Name Show Up On Net
Feb 13, 2011Sometimes my wireless connection goes away.It just started doing this the last 2 months. I have to get next to my router in order for it to come back. My name will be in the list and so is my neighbors.
View 2 Replies View RelatedCisco :: Show Ip Bgp Command Output S / D And H Values?
Aug 1, 2012I have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies View RelatedCisco :: When See Etherchannel Summary They Do Not Show Up As Layer 3?
Apr 15, 2012I have two MLS conected by 2 fast ethernet links f0/11 and f0/12 on both sides.I am trying to set up a layer 3 etherchannel using these two links . But when i see etherchannel summary, they dont show up as layer 3. Instead they show as layer 2.
View 19 Replies View RelatedCisco :: Show Command To View Ram Modules
Nov 30, 2011Looking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
View 3 Replies View RelatedCisco :: Command To Show Entire Configuration?
May 16, 2011Is there a command that can show EVERYTHING that is configured on a router or switchSeems if you're looking to save enough information to completely swap out a device the run/start config isn't enough.Settings like VTP and MTU settings aren't shown in the config file ... there may be other configuration settings like thisAm I forced to just know to check those settings are is there a command that will show the running-config AND all these other settings that aren't in the config?
View 8 Replies View RelatedCisco WAN :: 5505 - Show DNS For DHCP VLAN?
Apr 14, 2013I've got a 5505 and I'm getting a DHCP address from a cable modem. How can I show the DNS that the ASA is getting? show int vlan 2 is only givving me the IP and net mask.
View 2 Replies View RelatedCisco VPN :: 121 Output Of Show Crypto IPSec SA
Aug 18, 2011In a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies View RelatedCisco :: ASA 5585 Interfaces Show Unresponsive
Jul 11, 2012I'm monitoring 2 ASA 5585-x firewalls (in HA mode) using Cisco Prime LMS 4.2.1. The LMS server is connected to the firewalls on the inside interface.
My issue is that I keep on receiving Alert messages on Fault Monitor for both ASA firewalls listing all interfaces (except inside interface) as unresponsive.
My thought is that since the LMS server is not able to ping other active interfaces, it generates these alert messages.
My query is whether I'm thinking right? If yes, how can I prevent these unwanted messages from showing in Fault Monitor?
Cisco WAN :: 887 Doesn't Support Show DSL Command?
Jun 26, 2011The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies View RelatedCisco Switching/Routing :: 877 / Show DSL Interface ATM?
Aug 30, 2010i've got a Cisco 877 router connected to an ADSL link. i'm using the show dsl interface atm just to have a look on its performance. i've tried to search on Cisco website on how to interpret the output but a blog gave me more info [URL]. My question now is, what readings do i consider? is it on the left (ATU-R) or on the right (ATU-C)?
877ROUTER#sh dsl int atm0 ATU-R (DS) ATU-C (US)Modem Status: Showtime (DMTDSL_SHOWTIME)DSL Mode: ITU G.992.1 (G.DMT)ITU STD NUM: 0x01 0x01Vendor ID: 'ALCB' 'ALCB'Vendor Specific: 0x0000 0x0000Vendor Country: 0x00 0x0FCapacity Used: 31% 85%Noise Margin: 34.0 dB 10.0 dBOutput Power: 16.0 dBm 12.0 dBmAttenuation: 10.0 dB 6.0 dBDefect Status: None None Last Fail Code: NoneSelftest Result: 0x00Subfunction: 0x15Interrupts: 1453 (2
[code]....
Cisco AAA/Identity/Nac :: How To Show Logged In Users In ACS 5.1
Sep 5, 2011After some time no using Cisco ACS5.1, I still don't know how I can see all logged in users. I can see logging and check why an log in goes wrong, but in ACS 3.2 I just clicked on Reports and Activity and I could choose to see logged in users, or failed attempts, etc.
View 2 Replies View RelatedCisco :: OID To Show Total MAC Addresses In Use On 6509
Jul 28, 2011How to identify the OID to show the “total MAC Addresses In Use” on a 6509, This is the value we can see from a show mac-address counters, and I want our Solarwinds system to poll for it.
View 1 Replies View RelatedCisco :: 2800 - Show IP Flow Top-talkers
Aug 8, 2011I wish see the top talkers 10 at the my router 2800 IOS 12.4 (13a)
but when I run the command "show ip flow top-talkers" appear following:
% Top talkers not configured
I've set
Router(config)#ip flow-top-talkers
Router(config-flow-top-talkers)#top 10
I'm using the netflow version 9
maybe my router not support this issue ?? or it's missing some configuration.
Cisco WAN :: Interface FE0/0 On 2801 Show (changes State To Up)
Oct 8, 2009i have an Issue with my cisco 2801.in the logs shown me the interface FE0/0 cames up some times but never show the down state, I receive my internet service on this interface but never lost the conection, just this logs information
Oct 7 18:39:32.412: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 7 18:39:41.448: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 7 21:57:20.775: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 8 02:29:31.350: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
Oct 8 02:55:12.362: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
[code].....
the IOS Version that is running is
flash:c2801-adventerprisek9-mz.124-24.T1.bin