I have a solution of thre ACS.. one primary and two secondaries. My customer report me that in port of the switch where is connected the ACS show two mac address. [code]
View 1 RepliesHow to identify the OID to show the “total MAC Addresses In Use” on a 6509, This is the value we can see from a show mac-address counters, and I want our Solarwinds system to poll for it.
View 1 Replies View RelatedI can see what MAC addresses have a wireless session and I've used MAC Filtering to stop some MAC addresses from using the network at certain times, but they are still getting through to the internet. I don't know if they were to clone their MAC address as to whether this would show up with the cloned address in active sessions list. How I can stop some users from getting through at certain times? Any utility I can use on my Mac (Mac OS X 10.6. to show which computers/MAC addresses are on the network?
View 5 Replies View RelatedAfter some time no using Cisco ACS5.1, I still don't know how I can see all logged in users. I can see logging and check why an log in goes wrong, but in ACS 3.2 I just clicked on Reports and Activity and I could choose to see logged in users, or failed attempts, etc.
View 2 Replies View RelatedI imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.
View 1 Replies View RelatedI would like to add user (mac-addresses) to the ACS4.2 via RDBMS with a .csv file. How can I simultaneously add supplimentary user infos, like Real Name and Description ?
View 3 Replies View RelatedI have a very unusual issue with my installation of ISE on my VMWare ESXi 5.0 environment. but whenever I issue the command "show application statuse ise" I get the following output:
ISE Database listener is running, PID: 13675
ISE Database is running, number of processes: 27
ISE Application Server is running, PID: 15163
ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory
ISE M&T Session Database is not running.
ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory
ISE M&T Log Collector is running, PID: 15379
ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory
ISE M&T Log Processor is running, PID: 15457
ls: /opt/TimesTen/tt1121/lib/*.jar: No such file or directory
ISE M&T Alert Process is running, PID: 15296
Why my asa5520 brings out:
sh curpriv
Username : enable_15
Current privilege level : 15
Current Mode/s : P_PRIV
while i am logging in with my username which is XXXX. And in my ACS accounting logs I cannot see which user did what.
I am using ACS5.2 I want user to access the device with all necessary command like show run/ver/int/log… I try to set user privilege using Shell from 1 to 10 but show run doesn't work.
View 15 Replies View RelatedI have a self signed certificate on an ACS 4.2 Windows machine. I open a browser port to https://ipaddress:2002 of the acs and get the certificate error message as expected. When I proceed to the site then check the certificate via the shield on the top of the browser it shows is issued to ACSCOSC216_7. I install the certificate via the IE certificate import wizard.I then connect to the acs via the poper fqdn at [URL] login with my account but now get;The website declined to show this webpage.
View 1 Replies View RelatedIn setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies View RelatedI have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedHow to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedI have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedI'm trying to test such 802.1x wired environment:windows xp sp3 as supplicant windows NPS as radius server 2960 as authenticator latest anyconnect (3.1.01065) + nam and standalone profile editor.I have a question: What is the difference between protected identity pattern and unprotected identity pattern (set in nam profile editor)? As I understand documentation PEAP-MSCHAPv2 is a tunneled method and it uses un- protected identity pattern to protect user's identity during phase 0. But if I use any fake identity here (anonymous, anonymous@[domain], etc) access is rejected (Access-Reject in switch debugs). I have to use exacly the same pattern in unprotected identity pattern as in protected identity pattern ([username] or [username]@[domain]) to gain access, regardless of authenticaton mode (same in machine only, user only authentication).
View 1 Replies View RelatedI have a new Cisco Secure ACS 5.2 on a VM. We want to use it to for administrative access to our Cisco equipment with TACACS+. I am trying to map user permissions to different groups of devices based on active directory group membership, however it is not working.
I am using an LDAP (configured for secure authentication) external identity store. On the directory organization tab, I have confirmed the accuracy of the subject and group search base and the test configuration button shows that it's finding > 100 users and >100 groups.
On the directory groups page I have entered the groups according to the required format. cn=groupname1,ou=groups,dc=abc,dc=com
I have a rule based result selection under group mapping. I have two rules in the format below.
Conditon
LDAP:Externalgroups groupname1
Result
Identitygroup1
I have the default group set to a identity group named other. My problem is, no matter what user attempts to authenticate, the Default rule is applied, and the user is put into the other identity group.This occurs when I log on as a groupname1 user, groupname2 user, or as user that is not a member of either of those groups. LDAP authentication works and the user is able to logon to the device.
We are using ACS 5.2 and we are trying to create a Microsoft Active Directory (AD) Identity Store. We have a user to be used in the Active Directory creation General page and we would like to know how the test communication / ACS to AD communication takes place.
Our user is a predefined user in AD and has admin rights, but the password expires every 60 days. Will this affect the communication between AD and ACS 5.2 at everytime the entered user's password expires?
I'm currently looking for a solution in order to restrict the modification of the host internal identity store (add or delete MAC host) per group. The default administrator roles does not include "per group restriction". Under the ACS I defined one group per department? My objective it to allow each department to access their ACS MAC database to add or delete MAC addresses as required.
How to restrict internal identity store per group?Do I need to create new roles? and how?I was not able to get an answer from the ACS ADMIN manual.
I have a new ACS 5.3 configure and a ASA5550 to authenticate VPN users using a remote LDAP server. Once I try to authenticate the users with the ACS it gives me the error message "22056 Subject not found in the applicable identity store(s)."
I checked out the documentation and have already configure the Identity store sequences to redirect everything to the LDAP server, I also did the Bind test and it says that is ok, but I still have the same problem.
I validated the Access Policies Menu, and tried to create a new Service Selection Rules, but whet I get to the option of modifying the Identity option I get the error: "This System Failure occurred: {0}. Your changes have not been saved.Click OK to return to the list page. " and I'm not able to modify the identity, not in this new option I created, nor in the ones already created in the ACS.
I have two ACS v 5.2 (primary and secundary) and some users are in the internal stor and the others are in the AD.The local site topology is like this:
PC - AP - WLC - ACS - AD
Authentication method is PEAP(EAP-MSCHAPv2) and all user have the certificate company installed. The OS in the client users is Windows 7.Users was working fine but some users reports intranet disconnections. I see in the ACS log many "22056 Subject not found in the applicable identity store(s)." and "24415 User authentication against Active Directory failed since user's account is locked out" alarms.I believed it was because user wasn´t in the AD data base, but some times the same user is authenticated successfull and other i see the "22056...." or "24415...." alarms.
I switched the role for ACS primary to works as secundary and we see the same alarms.
I have ACS 5.2 running as a VM. I'm AD, then local authentication successfully for device access, but I want to define ACS user groups to restrict login. I don;t see any way to do this. If I use AD groups, they don;t show up as selection options on the policy screens, just the ACS locallyy defined groups.
View 1 Replies View RelatedWe have a ACS 4.3.2 installed with users authenticating against an Active Directory database. The AD database not only authenticate the users but also assigns the group that is used to select IP address pool.Now the requirements require to use token authentication with SafeNet. This authentication uses the same username but the password is composed of the original password + OTP.The problem is that the SafeNet server doesn't return the group membership.I've read about the Identity Store Sequence in ACS 5.x and I think I could use it in the following sequence:! configure an Authentication Sequence using the SafeNet token server (this works with ACS 4.x)I configure an Attribute Retrieval Sequence against the AD database. This would use the username only, no password and would retrieve the group membership.
View 1 Replies View RelatedI'm looking for Cisco ISE v1.1 to use the following licensing feature. url...Endpoint is dynamically profiled by Cisco ISE and assigned dynamically or statically to an endpoint identity group. Cisco ISE authorization rules do not use this endpoint identity group.
View 2 Replies View RelatedI am currently running cisco ACS 5.1.0.44 and use active directory as the main authentication identity store to allow network administrators to have access to network devices in my organization .As per the established security policies in my organization , the ACS has to disable any account after 3 failed login attempts to any network devices .i have gone through all the settings oN the acs but couldn't find where or how it is done .
View 3 Replies View RelatedI have installed ACS 5.4 and we are looking to authenticate our Anyconnect users with ACS via Active Directory. I think I have the correct commands in our ASA ( we had ACS 4 and authenticated our anyconnect users ).
I also have configured ACS to use Active Directory and installed the server side cert in ACS. I'm just uncertain how to program ACS to use the security group that I have setup in Active Directory.
I have an ACS 5.3 cluster, that is configured to use AD. There are a few wireless devices, and monitoring tools that do not have AD accounts. I would like to configure ACS to first check AD for the user authentication, and if that fails to roll over to the local (Internal Users) identity source where I can define these user accounts.
It seems that when the authentication hits the initial Identity Policy rule, it never moves onto the next one if the first fails.
Attached are screen shots that show how i'm configured for the test, i have a local user defined and I'm trying to log into the firewalls.
- Identity Definition : Screen shot of the main ACS definition for the rule i'm testing that's not working
- Identity Rule 1 : The configuration of rule 1 that if it fails i need it to move onto rule 2.
- Log Output : Screen shot for one of the failed attempts from the ACS View Log server.
Reason I need to configure it this way is:
- Wireless users authenticate to wireless using AD user accounts. Some hand held scanners do not support that and will need to authenticate using the MAC address.
- Authentication to Network devices for managment uses AD accounts. We have some monitoring tools that do not have AD accounts, and will need to be able to log into Network devices to issue some commands (Examples: Cisco Prime LMS and NCS, Infoblox NetMRI).
how profiling works exactly ?How intelligent is the profiling engine, meaning: Will it discover that one device has more than one different MACs and will merge the entries in the database ??
Example:This is in fact the same device, there is only one WLC-2500 in the network ....If it can discover that, what needs to be configured on the ISE to do that ?
I have setup an Identity Firewall on a ASA version 5.6 on a DMZ interface.I have installed the ADAgent on a domain member Win2008 and configured as follows: [code]
where ashdew is a domain user and ACL 122(only one line) is applied on the dmz interface and NAT is properly configured.The ADagent has been properly tested and ASA can register to it.The ASA can connect to AD DC controller and query user database.I have placed a laptop ip 172.17.h.x on the DMZ and can ping the DMZ interface.
The laptop cannot authenticate on the domain and the asa does not seem to retrieve the user identity.Do I need to add extra rules in the access-list 122 to permit trafic to DC?Can I check on the AD Agent if it can retrieve the user to ip mapping ?
I understand that Cisco Secure ACS 5.3 supports the integration with existing external identity repositories such as Windows Active Directory and LDAP servers. In fact, in my environment, my ACS 5.3 is now integrated with AD and RSA.My question here is can Cisco Secure ACS 5.3 integrate with "multiple" WIndows AD, LDAP, RSA Server etc.? if yes, is there a Cisco document stating this? The keyword here is multipple.
View 4 Replies View RelatedI am trying to setup PEAP authentication for wireless users but I got stuck at place where I have single ssid and users are store in different identity stores like some will be using their active directory and some are locally created users on ACS. I created separate service for wireless authentication and under that I am unable to create rule to differentiate them with identity stores. any idea how to achieve this.
I tried creating identity selection based on role but it does not work as for protocol like radius.peap,ms-chap ACS does not look for another identity store once user not find in an identity stores.
After clicking on below path we are not getting option as should be reflected. Below is the snapshots for the issues.
Access Policies > Access Services > Default Device Admin > Identity
We got a bunch of port-sec violations on port fa1/0/42. after checking logs, we noticed that the MAC address responsible for generating the alert was not one, but many.We asked the user, he said he only restarted his computer.The MAC addresses happen to be existing MAC on the network.How is it possible that a port-sec violation is made by many MAC addresses on the same port, successively?
Syslog message generated from device SW_Etage1: May 25 15:17:08 10.100.254.11 1454802: May 25 15:19:11.693 CET: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 6416.8dbb.930e on port FastEthernet1/0/42.
Syslog message generated from device SW_Etage1: May 25 15:17:29 10.100.254.11 1454805: May 25 15:19:32.874 CET: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 78e3.b58f.1011 on port FastEthernet1/0/42.
[code]....