Cisco :: Devices Don't Show In NCS 1.0
Sep 15, 2011I've added several switches and one WLC to my new NCS Prime box. I don't see them in the display. If I try to readd one, it says it already exists. What am I missing?
View 0 Replies
ADVERTISEMENT
Windows XP - No Network Devices Show Up
Mar 20, 2011I'm running Windows XP, SP3. This is a friends computer that I'm trying to fix. It had a virus which I removed, however it left behind a damaged computer. Now there are no network devices that show up in "Network Connections" or in Device Manager. I tried to reinstall the drivers, but I got this error: "The Realtek Ethernet Controller was not found. If Deep Sleep Mode is enabled Please Plug [sic] the Cable".
View 1 Replies View RelatedCisco :: LMS 4.2.1 Fault Setup Doesn't Show Any Devices
Aug 8, 2012LMS discoverd all my devices and updated the DCR. This devices are visible in DFM. For some of this devices i would like to change the threshold values. For some reason the devices are not visible in Monitor->Fault Settings->Seup->Threshold Settings (please see screenshot) Is there another approach to change the threshold values?
View 5 Replies View RelatedCisco :: 3550 - Show Power Usage For Devices
Jan 27, 2013Is there anyway I can see the power usage on either a 3550 switch and/or 7301 router? I have some far away I wish to see the usage off.
Devices with module power supplies like cat 4500s/6500s/7600 etc all have commands like "show power ...", which will show me input voltage, current and power usage in watts. Is there anything like this for devices without module power supplies?
Netgear DG2200 Devices Won't Show Up On Network
Sep 1, 2011I have two computers, one vista (Laptop) the other XP (Desktop). Now the problem is that i can't see my vista laptop on my XP, but both are connected to the same router (Netgear DG2200). The router also has a hard drive connected as a network drive WHICH i can see on the XP.
Problem is, nothing comes up on the Vista laptop except for the router and itself. Not even the network hard drive. I can view it on my PS3, though.
I noticed my lan is not enabled on my laptop, so how do i enable it? I tried diagnosing but it said to connect the lan cable.
Command Prompt To Show Devices On Network?
Jan 30, 2013I am running windows 7 HP. We have about 10 devices in one office and 5 devices connected thru a VPN..... When i hooked everything up 4 weeks ago I could see all the devices in the main office and the remote office connected thru the VPN (In the Network Folder that lists everything connected). Now I only see like 4 device and they are all in the main office.
I did some research a couple weeks ago and found a command prompt that "refreshed" all the devices that were connected, but now They are gone again and I cannot remember the command prompt!
Scanner Doesn't Show Up At All In Local Network Devices
Nov 12, 2011Im working for a client at the moment and I've had to setup a network printer for them, I've got 4 Windows 7 machines easily printing over the network to this printer that is connected wirelessly but they want one of there machines to use the scanning functionality of the printer.The scanner doesn't show up at all in the local network devices like the printer does and to be honest i don't really have any experience with scanning over a network to a windows 7 machine, but this printer does support scan to ftp so my idea is to setup a small ftp server on the windows 7 machine with a folder to stored scans on the desktop or something, then put the details of the server in to the printer making it as easy as possible for the customer to scan stuff and just get it from the folder on the desktop, i could also share this folder over the network for anyone to open and get a scan if needs be.
View 2 Replies View RelatedD-Link DAP-1522 :: Devices Local Do Not Show On Network Map
May 17, 2011This is the configuration I am running:Internet > Cable Modem > Netgear WNDR3700 Router ~~ DAP-1522 > Wired Windows 7 PC + Linux PC + Printer.The Windows 7 and Linus PC's do communicate well to the internet as do any laptops accessing the router wirelessly and any devices wired to the router. That is the good news.
The bad news is that any devices located after the DAP-1522, including the DAP-1522 do not show up on the network map of either the router or any of the wireless laptops. Neither does the Win 7 PC connected through the DAP-1522 show any networked devices, whether through the DAP-1522 or not, even though network discovery is turned on.
Right now the DAP-1522 is set up to function as a bridge and is in "Static IP" mode. I tried changing it to DHCP, but the DAP-1522 will not allow saving that setting, even though it will allow changing it. It just reverts back to "Static IP". The firmware version is 1.31, and the firmware update went well after a workable logon to the admin page was discovered. Also the one-button (WPS) set-up to the router worked as far as allowing an internet connection.
What needs to change to allow all the devices to show up on the network maps and maintain internet access? Ultimately, I would like to stabilize the IP's of the major components of the network to make troubleshooting easier. But to do that the devices need to show up on the network maps, particularly of the router, so they can be added to the IP reservation table by selection.
Linksys Wireless Router :: EA 6500 Cannot Show Online Devices?
Jan 11, 2013My EA 6500 Linksys router does not show online devices. Current firmware version is 1.1.28.146856.
View 2 Replies View RelatedLinksys Wireless Router :: E4200 - No Led To Show Connected Devices Status
Oct 31, 2011I'm thinking of upgrading from my Linksys WRT54G router to the E4200 and though I've goggled. Also, are there no LEDs on this unit to tell you the status of what's connected?
E3000WRT-54GWVC-80N
Linksys Wireless Router :: Why Doesn't E4200 Wireless Router Show All Attached Devices
May 1, 2013I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results. Other than a factory reset, get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago?
View 2 Replies View RelatedCisco Switching/Routing :: 3750 - Show Interface Vlan (ID) Doesn't Show In / Out Traffic Rate
Mar 13, 2013I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedCisco :: Understand Show Sessions And Show Connection Commands?
Jan 29, 2012How to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedCisco Switching/Routing :: 2960 Don't Display Logging Trap Informational In Show Running / Show Startup
May 27, 2012Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedCisco :: BRI Card Does Not Show In (show Voice Port)
Jun 18, 2011I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedTEGs80G - Swap Unmanaged Devices With More Expensive Cisco Devices?
Jun 1, 2012Currently my home network is being switched via TrendNet TEGs80G unmanaged gig switches. I have been using them for about a year now with no issues. As my home network becomes more advanced, I recently just added a Cisco ASA5505, I am thinking about swapping those unmanaged devices, 4 of them, to managed. I was looking at the Cisco SG300-10 for upstairs, and a 16 port variant for my main core. These devices do not support full Cisco IOS cli, but they are manageable with a rich feature set nonetheless. My question is, should I swap the unmanaged devices with the more expensive Cisco devices, or just keep what works and save the money until I really need to spend it. As previously stated, my home LAN works just fine as it is, however my WiFi, NTV550s, server and workstations are all on the same network. Probably not the most secure but it is what it is without VLAN support.
View 11 Replies View RelatedLinksys Wireless Router :: E4200 Can See None Of Devices Attached To Power-line Devices
Aug 15, 2011I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies View RelatedWireless Devices Can't Connect To Wired Devices?
Oct 11, 2012All of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
View 1 Replies View RelatedCisco :: ASA 8.3 With ASDM 6.3 Show Log On ACL?
Jan 20, 2011I am trying to see what traffic goes through a certain ACL so I specify a protocol instead of allow all IP traffic. So what I did is enabled logging with debugging on that ACL. When I right click on the ACL and show log, nothing shows up. But I see hits on the ACL.
View 1 Replies View RelatedCisco :: Show Dynamic PAT Table?
Nov 6, 2012Trying to get a Cisco ASA 5505 to show me all the current dynamic PAT. (I don't want to see hard-coded port forwarding, just dynamic stuff the router is doing to allow various hosts on the network to talk to the WAN.)
View 8 Replies View RelatedCisco WAN :: Show Ip Route On 1841?
Dec 13, 2010We have a Cisco 1841 router and checked something an unnusual (never seen before) routing table having L - local routes. if this an IOS bug or same as C - connected local routes.
1841#sh verCisco IOS Software,
1841 Software (C1841-IPBASE-M),
Version 15.0(1)M3, RELEASE SOFTWARE (fc2)Technical Support: [URL] ... Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Sun 18-Jul-10 01:16 by prod_rel_team
[Code] .....
Cisco WAN :: Show All Module On ASR 1004?
Feb 14, 2012how to show all the module on the ASR 1004?
View 4 Replies View RelatedCisco :: 5508 WLC Show Configuration
Nov 19, 2011I would like to know whether there is any command that shows the configuration of the wireless controller (5508) like when you upload the configuration file from the GUI of the WLC. In other words, I don't want to show me all the verbose running configuration as the "show running-config", but a brief configuration as for example described below: [code]
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.3 Show Two Mac Addresses
Apr 16, 2012I have a solution of thre ACS.. one primary and two secondaries. My customer report me that in port of the switch where is connected the ACS show two mac address. [code]
View 1 Replies View RelatedCisco WAN :: Show Modules In ASR1006?
Feb 15, 2012In a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
View 1 Replies View RelatedCisco :: Show Ip Bgp Command Output S / D And H Values?
Aug 1, 2012I have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies View RelatedCisco :: When See Etherchannel Summary They Do Not Show Up As Layer 3?
Apr 15, 2012I have two MLS conected by 2 fast ethernet links f0/11 and f0/12 on both sides.I am trying to set up a layer 3 etherchannel using these two links . But when i see etherchannel summary, they dont show up as layer 3. Instead they show as layer 2.
View 19 Replies View RelatedCisco :: Show Command To View Ram Modules
Nov 30, 2011Looking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
View 3 Replies View RelatedCisco :: Command To Show Entire Configuration?
May 16, 2011Is there a command that can show EVERYTHING that is configured on a router or switchSeems if you're looking to save enough information to completely swap out a device the run/start config isn't enough.Settings like VTP and MTU settings aren't shown in the config file ... there may be other configuration settings like thisAm I forced to just know to check those settings are is there a command that will show the running-config AND all these other settings that aren't in the config?
View 8 Replies View RelatedCisco WAN :: 5505 - Show DNS For DHCP VLAN?
Apr 14, 2013I've got a 5505 and I'm getting a DHCP address from a cable modem. How can I show the DNS that the ASA is getting? show int vlan 2 is only givving me the IP and net mask.
View 2 Replies View RelatedCisco VPN :: 121 Output Of Show Crypto IPSec SA
Aug 18, 2011In a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies View RelatedCisco :: ASA 5585 Interfaces Show Unresponsive
Jul 11, 2012I'm monitoring 2 ASA 5585-x firewalls (in HA mode) using Cisco Prime LMS 4.2.1. The LMS server is connected to the firewalls on the inside interface.
My issue is that I keep on receiving Alert messages on Fault Monitor for both ASA firewalls listing all interfaces (except inside interface) as unresponsive.
My thought is that since the LMS server is not able to ping other active interfaces, it generates these alert messages.
My query is whether I'm thinking right? If yes, how can I prevent these unwanted messages from showing in Fault Monitor?
Cisco WAN :: 887 Doesn't Support Show DSL Command?
Jun 26, 2011The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies View Related