I am trying to see what traffic goes through a certain ACL so I specify a protocol instead of allow all IP traffic. So what I did is enabled logging with debugging on that ACL. When I right click on the ACL and show log, nothing shows up. But I see hits on the ACL.
View 1 RepliesI was checking out the config on my ASA and noticed a bunch of static routes configured when I did a show route. With the exception of two that I expect to be there, the remainder point traffic destined for specific internal hosts to the outside interface, i.e.
S private_ip 255.255.255.255 [1/0] via public_ip, outside
I verified that I cannot ping those hosts from the firewall. I logged in to the ASDM. When I check the Configuration>Device Setup>Routing>Static Routes it only shows two static routes, the ones I expect to see. If I look under Monitoring>Routing>Routes, I see the same output as I did on the CLI. I looked around to see if I was missing a key location for this information, and I was able to see the same static routes output in Monitoring>Routing>Routes. Since this is under monitoring though there's no way to delete these routes, and I still don't know where they were configured originally. Then I happened to check under Monitoring>VPN>VPN Statistics>Sessions, and I see several of the private IPs used in the static routes being used by VPN users, including my own! I know I didn't assign myself a static IP for VPN use or anything like that. So, what are these static IP routes? Why do I see them in the CLI and not under the Configuration tab? I mean, I know I can delete them from the CLI but I'm trying to figure out why the info is not synced. Am I seeing dynamically created content based on the VPN connections?
I created some acess-lists, and you can assign a logging level to this access-list. Now this ACL has a lot of hits, so i want to see whats happening. Only the log I then see is completely empty. I cannot figure out how to get some info in that log.
I think there is some global logging setting i probably need to enable in order to get anything logged at all, but i cannot figure out which.
Yesterday, I configured ASA via CLI for Static PAT and created some entries in an access-list. I will be testing that setup this evening.
However on a quick double check of the settings on the device via ASDM I could not see the acess-list settings. I searched every tab and found nothing so I PuTTYed into the device and checked the running config. The rules I created were right there. Is this something I should expect? If so doesn't it defeat the point of having a GUI if it does not show a complete running config?
nat global entry not showing up in ASDM but it does via CLI see blow, it's a policy NAT.
nat (inside) 5 access-list inside_nat_outbound_4
global (outside) 5 ************-OUTSIDE netmask 255.0.0.0
Global 5 doesnt show in ASDM 6.1 (5) the globals only go up to 3
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedHow to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedI have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedI have two identical ASA 5505. I can only access through https/asdm on one of the devices from same laptop. Below is the configuration of the ASA. My internal machine ip address 10.0.0.10/8. I have tried to remove and re-enter the "http" and "Crypto key" related command. Wireshark show "Alert (level: Fatal, Description: Handshake Failure)" right after I entered URL in browser-tried IE and Chrome. Java version should not be a problem as I can access the second ASA.
View 5 Replies View RelatedI can get to the untrusted certificate on https....coming from my address 192.168.133.205..but i get denied am i being denied by access list?..I dont see how since intital SSL begins..
these are the log from the ASA---10.11.24.11 is the ip of one of the contexts
interface GigabitEthernet0/1.124 vlan 124 nameif Inside security-level 100 ip address 10.11.24.11 255.255.255.0
http server enablehttp 0.0.0.0 0.0.0.0 managementhttp 0.0.0.0 0.0.0.0 Inside
Mar 22 2010 16:05:34: %ASA-6-725001: Starting SSL handshake with client Inside:192.168.133.205/24368 for TLSv1 session.Mar 22 2010 16:05:34: %ASA-6-725003: SSL client Inside:192.168.133.205/24368 request to resume previous session.Mar 22
[Code]....
I've configured a couple of ACL rules via CLI in my ASA. When i checked in the ASDM, it only shows the basic rules that was configured by default and did not show the rules that i've created.
View 6 Replies View RelatedI want to perform log in ASDM if there is some one remote to server inside ASA by vpn. Does ASA 5050 able to show the log from ASDM.
View 1 Replies View RelatedWe are running ASA5520 with version 8.4(2)8 software and ASDM 6.4(5)205.We have noticed the following problems:When having more than 30 IPSec,sessions connected, the log fills up with errors "System is low on free memory blocks of size...", When filtering by "AnyConnect Client" in "Monitoring > VPN > VPN Statistics > Sessions" the values "Bytes Tx / Bytes Rx" column is presented in one line ie. "8450198968129194". Seems to be missing a <cr><lf>,When uploading a new CSD-image (via ASDM) all configuration för GPO, CP, DAP seems to dissapear, though, the config seems ok when looking at a sh run. Also, the newly updated csd-image doesn't show i ASDM.
View 2 Replies View RelatedI'm trying to access ASDM but everytime I put in the IP address I just get cannot display webpage: Here is the copy of my configuration
ASA Version 9.1(1)
!
hostname ciscoasa
[Code].....
The history about this box is that they had access through the ASDM untill they changed the management interfaces to Vlan 50.
The pix firewall is 192.168.50.10 and my interface to my PC is on Vlan 10 which is 192.168.10.115. I can ping 192.168.50.10 but I am unable to access this through ASDM. I believe the pix is denying me.
When I look in the config i see the ASDM image and I see that they have http server enabled.
I see my network 192.168.10.0 as inside but I don't see 192.168.50.0.
I have recently upgraded ASA to 8.4 and found that ASDM is not working on it. I tried the latest ASDM version 7.1 still no luck. When I try to access ASA using IE...it just shows " Page can not be displayed "
Following is the config which I have
http server enable
http 0.0.0.0 0.0.0.0 inside
http 10.52.193.218 255.255.255.255 inside
asdm image disk0:/asdm-711-52.bin
asdm location 0.0.0.0 0.0.0.0 inside
asdm history enable
Is there anything else required in ASA 8.4 for ASDM to work? When I telnet to ASA interface with 443 port it works
im working on a small project on a asa 5505 and beacuse i do most of the work from the outsidei want to open up asdm without vpn.
i have it working on another asa and the only difference is the rom version.the one not working is 8.0(5) - 6.2(3) and the one working is 8.0(4) - 6.1(5) did they do some changes?
I am having issue logging into my Cisco ASA 5505 ASDM interface. It prompts for a username and password but it will not authenticate. When I look at the http debug it tells me that authentication failed. I have tried with both username and password as well as with just a password.
View 6 Replies View RelatedASDM cannot be loaded. Click OK to exit ASDM. Server returned HTTP response code: 503 for URL...
I'm attempting to access the ASDM externally (where x.x.x.x is the external IP). I was able to access 3 days ago just fine. So far, I've found suggest a reboot.
ASA Version 8.2(1) - I think the ASDM version is 6.2
I was going through the release notes on cisco website of ASA 8.4.6 and ASDM 7.1.3 but I just can not find a definitely answer: if ASDM 7.1.3 can run with 8.4.6?
View 2 Replies View RelatedRecently powered down device (transformer overhaul) and when it booted back up, unable to access with ASDM, SSH...can access directly using HyperTerm, but have only limited commands...will not accept known user/password credentials. When I issue 'show flash' I can see that there are upgrade_startup_errors.log files, but cannot access them.
View 5 Replies View RelatedI am trying to enable a second WAN interface on our ASA.the end goal is to move all internet traffic to the new connection, but first i want to test it working.I have setup my computer as an object in the ASDM and the interface is configured correctly (same settings on a different router and that was working)I setup a route with a lower metric ( 1 lower than the default route which routes everything through current main internet interface) to route traffic from my computer out through the new interface but i am still connected on the old interface.I duplicated some of th NAT rules (but i would have thought if these werent working then i would have no internet connection anyway)
View 5 Replies View RelatedI have been browsing the forum and the support notes for a couple of hours and haven't found a definitive answer to my question. Our ASA is on the subject versions. I watched a video on YouTube stating that upgrading the ASA is easiest if you upgrade ASDM, then the ASA. Problem is, I don't think I can upgrade ASDM first because I don't see a version that is compatible with ASA 7.2.x and 8.0.x.
View 3 Replies View RelatedI recently upgraded an ASA 5505 that has the Advanced Endpoint Assessment License to 8.4(3) and ASDM 6.4(7). Now there are no options in ASDM for adding AV, Firewall or AntiSpyware versions and definition levels etc? I have checked Host Scan Extensions and enabled 'Advanced Endpoint Assessment ver 3.5.3.1' however when I click configure and attempt to add any AV etc there are none to select - the 'Add Products' box is just blank.I have AnyConnect 3.0.5075, CSD 3.6.4021 and have tried with the integrated AnyConnect Host Scan image and with the standalone Host Scan image (3.0.5077) and the behaviour is the same ?
View 4 Replies View RelatedI got a PIX 501 off ebay and im trying to upgrade it to have an ASDM image on it.Ive downloaded every copy of the ASDM image i can get my hands on, and when i transfer it to the PIX when its up and running i get out of memory, If i do it through monitor mode, i get the error "bad magic number" no matter what i transfer to itI can transfer a new image to the PIX (a non asdm one through monitor mode.
View 3 Replies View RelatedI've been struggling to get ASDM (PDM) installed and running on my PIX 515e. The PIX IOS version is 7.2.4(30) The ASDM version I've copied to flash is 524.
I've followed the Cisco documentation verbatim, however I still cannot connect via the Java ASDM client or via http. When I try to connect via http, my PIX shows the following error: "tcp access denied by acl from..." I do not this this is a security (ACL) issue as I've tested after opening everything up and still no luck.
Here's my running config (w/ the relevant statements prepended with ">>>"):
show run
: Saved
:
[Code]....
I Have Cisco 5540 with AIP-SSM-40, recently i config AIP-SSM-40 to capture all traffic from all interface any to any with promiscous mode and if card fail traffic still flow throuh asa, but after that i can't login to cisco ASDM, the error is "Un Able To Launch Device Manager From xx.xx.xx.xx"
View 2 Replies View RelatedI want to kown if is posible install IOS 8.3(2) and asdm 6.3(1) in firewall 5505 wich has 512MB of RAM and 128MB of flash. I installed it but according to the cisco page it can´t. maybe could work bad ?
View 1 Replies View RelatedI have a firewall Cisco ASA 5505, and currently it is a command line firewall. I want to configure ASDM so that i can use it as a GUI Web Base interface.I really don't know what to do. How can I configure ASDM on my firewall.
View 7 Replies View RelatedI need connecting ASDM to ASA 5525x management port its a brand new ASA i just updated ios and ASDM port configuration is following
Management por 0/0 ip 192.168.1.1
secure-level 100
http server enable
http 192.168.1.10 255.255.255.255 inside
port is up
When I am launching Internet explorer it just said cant connect Chrome shows connection with 192.168.1.1 is was interrupted but i can ping asa and backward .
I bought a pix 515 to play with and i upgraded it to the farthest release 8.0(4) it was at 7.22 and the web interface and ASDM is not working. do i need to upgrade the ASDM? when i run the launcher i get a fatal error :
handshake_failure.
I just updated the IOS, did i need to save certain things? activation key's maybe???
i have test to access the firewall of ASA5510 with ASA845-K8/asa902-k8bin + asdm-712.bin +JAVA6 / 7, is completely no problem
When i try to install a new ASA5505 existing IOS is asdm825-k8 and also asdm-712 with JAVA7 is not allow to access the firewall with ASDM
After i type in username password, it stuck on the page loading , sometimes it will come up with cannnot to the device something like that.
telnet and SSH is no problem, i still can download the IOS with TFTP.
I think may be the java problem, because i just to connect with wrong ip and password, it also stuck in this page.