I created some acess-lists, and you can assign a logging level to this access-list. Now this ACL has a lot of hits, so i want to see whats happening. Only the log I then see is completely empty. I cannot figure out how to get some info in that log.
I think there is some global logging setting i probably need to enable in order to get anything logged at all, but i cannot figure out which.
Yesterday, I configured ASA via CLI for Static PAT and created some entries in an access-list. I will be testing that setup this evening.
However on a quick double check of the settings on the device via ASDM I could not see the acess-list settings. I searched every tab and found nothing so I PuTTYed into the device and checked the running config. The rules I created were right there. Is this something I should expect? If so doesn't it defeat the point of having a GUI if it does not show a complete running config?
Recently powered down device (transformer overhaul) and when it booted back up, unable to access with ASDM, SSH...can access directly using HyperTerm, but have only limited commands...will not accept known user/password credentials. When I issue 'show flash' I can see that there are upgrade_startup_errors.log files, but cannot access them.
View 5 Replies View RelatedI do have one other question first. What's the effect of the crypto key zeroize rsa command, and then crypto key generate rsa modulus 1024 while I'm SSH'd to the ASA? Can I do it? Or do i need to be consoled in or connected a different way?
ASA 5510:
ASA Version 8.4(1)
asdm image disk0:/asdm-641.bin
asdm history enable
http server enable
http 10.1.1.83 255.255.255.255 inside
http 10.1.1.82 255.255.255.255 inside
Shouldn't that right there be enough to access ASDM from either host .82 or .83? Because I cannot. But if I add http 0.0.0.0 0.0.0.0 inside, then I of course can.
I have a cisco ASA 5510 that I have set up currently to access via ASDM through the Inside interface. When I VPN in using our older VPN server I can connect to it fine. I recently set up the ASA to also be a VPN server which will eventually replace the older server for our HQ. I noticed that when I'm VPN using the ASA as the VPN server, I can only ASDM to the public which I prefer not to allow. Access to the inside doesn't seem to work this way. What configurations if any would be causing this. I'm assuming it's some thing I need to adjust in the VPN configuration.
View 3 Replies View RelatedSo I've run into a problem on my ASA5510, post-upgrade I can no longer connect to the inside interface from across our L2L VPN. I've tried both ASDM and SSH and the connections fail. I see in the logs that the attempt is being made, but it will eventually time out. There have been no problems with this type of connection with any previous upgrades, just this particular upgrade, I went from 8.4(1) to 8.4(2). I don't see much in the release notes or anything in a pre/post config diff that jumps out as a cause to this behavior. The only thing I did see in the release notes "CSCtg50770 Mngt-access (ASDM,SSH) to inside intf of 5580 fails over RA VPN session" which sounds like it could be my problem, but that was in the "Fixed in 8.4(2)" section and says it's for a 5580, maybe the fix for the 5580 broke it on a 5510??? I hope not and that I'm simply missing some new setting that I need to enable for this type of connection as this device is in a remote office.
View 2 Replies View Relatedi am unable to launch ASDM, and access https:// to run Asdm..everything worked find yesterday but now for some reason it wont work?When i am trying to log in with the asdm it just hangs on the connecting to device... please wait...When i am tryng access the https://... i get the ssl do you want to trust.. and i press proceed anyway and i get an error
Asa 5510
Device manager version 6.1
System image file is "disk0:/asa804-k8.bin
Also i am accessing the asa with ssh without any issues
How to designate access-list for the remote access vpn users in order to let them access specific subnet or host,asa 5510 and acs is in the picture
View 9 Replies View RelatedI have just upgraded a ASA5510 from 8.2 to 8.3 using migration tool.All seemed to go well, still double checking the config as this is a bench test of upgrade prior to filed upgrades.
Anyway one thing that is slightly frustrating is that the migration has expanded all of my access-lists, so we maybe had 10 lines of config relating to access-lists based on access-groups, now we have hundreds of lines.On ASDM this is bad enough but on CLI with show run its a bit of a bind.
Is there any way to un-expand the access list or do I simply delete and start again using my access groups.
how to totaly disable Admin/ASDM access on our public interface of our 5510. I don't want to change IPSec or SSL access to the outside interface. Just totaly disable access to Admin/ASDM from the outside without halting all other access.
View 3 Replies View RelatedI was checking out the config on my ASA and noticed a bunch of static routes configured when I did a show route. With the exception of two that I expect to be there, the remainder point traffic destined for specific internal hosts to the outside interface, i.e.
S private_ip 255.255.255.255 [1/0] via public_ip, outside
I verified that I cannot ping those hosts from the firewall. I logged in to the ASDM. When I check the Configuration>Device Setup>Routing>Static Routes it only shows two static routes, the ones I expect to see. If I look under Monitoring>Routing>Routes, I see the same output as I did on the CLI. I looked around to see if I was missing a key location for this information, and I was able to see the same static routes output in Monitoring>Routing>Routes. Since this is under monitoring though there's no way to delete these routes, and I still don't know where they were configured originally. Then I happened to check under Monitoring>VPN>VPN Statistics>Sessions, and I see several of the private IPs used in the static routes being used by VPN users, including my own! I know I didn't assign myself a static IP for VPN use or anything like that. So, what are these static IP routes? Why do I see them in the CLI and not under the Configuration tab? I mean, I know I can delete them from the CLI but I'm trying to figure out why the info is not synced. Am I seeing dynamically created content based on the VPN connections?
I want to do something with IP SLA and started by estabilishing a baseline.
I'm trying to check history on an ASR. I tested same config on a 3845 and was forgetting the "history filter all". After this I could see history table on 3845 but still history is empty on the ASR1006. The operation started because I can see information with "show ip sla statistics".
know if i missed something or maybe this is not supported in ASR1006?
re-ld-tcc-02_ASR1006#show vers
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(1)S2, RELEASE SOFTWARE (fc1)
[Code]......
i repalced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key key address Y.Y.Y.Y no-xauth
[code]...
keys match , crypto isakmp policy is same , IOSs supoort VPN .interess traffic alse been initiated from both side and all worker in old cisco router with same configuration?
I would just like to to open UDP port 123 in the ASA 5510 Firewall so that our Primary Domain Controller could use this port to sync time with an external time source. We have already added an access rule for this port under the firewall configuration in ASDM 6.4 and this port was also allowed in the inbound and outbound rule of the PDC's Firewall but it seems that it was still blocked.
View 23 Replies View RelatedI have an ASA 5510 in a live environment. Up til a short while ago I could access this via the ASDM and ssh. However I can no longer connect to it via eithier. When I access It via SSH I get a disclaimer saying the following
*** You have entered a restricted zone! Authorized access only!!! Disconnect immediately if you are not authorized user! ***
It then cuts me off.
When I try to access the ASDM I get the following
The firewall is running all its services without a problem and I can ping the device without any issues. Also none of the config (to my knpowledge has been changed). I set up a console session and http server enable is still there with
http 192.168.200.0 255.255.255.0 inside
Customers ASA 5510 and they are using the default "pix" login. I can log into the command line with pix just fine. I created a user account, call it:username jsmith password Passw0rd priv 15,I'm unable to log into the command line with jsmith. I can get into ASDM with it.
View 6 Replies View RelatedI have just erased an ASA and upgraded the firmware and then added an IP. How can I enable the ASDM as I can't get on it, here is the config:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
dns-guard
[code]....
We are running a Cisco ASA 5510 in our district. We have been using it for about a year and a half after an upgrade from our PIX. I have been using the CLI to manage it but I wanted to start using the ASDM. I installed the ASDM Launcher last Friday but could not access it. I have enable the http server on the ASA, assigned an IP to the interface, and granted my machine's IP inside access. On Friday I was unable to launch the ASDM. I then downgraded Java. I came in this morning and was able to connect through the launcher. However I could not make any changes as it would give me an error message and often popped up with "lost connection" type messages. I then closed the ASDM but could not reconnect after that. When I try to connect through the launcher I receive the message "Unable to launch ASDM from 172.16.5.1: Connection reset". When I try https://172.16.5.1/admin/ from a browser I simply receive "page cannot be displayed". I'm not sure why I can't connect.
[Code] ........
Running Asa5510, 8.2.5, with asdm 6.4.5 and I am looking for a graph in asdm that will show me what protocols and internal ip addresses uses the most traffic. Maybe a bit like "Top 10 protected servers under SYN attach". My reason for this is of cause I see a very high traffic pattern from one of my interface during the day and need to identify what is using bandwidth, protocol and source address.
I could use Net Flow feature in the Asa, but it´s not "real time" and forces me to setup a net flow collector. Can 8.2.5 not give me this information with built-in graph/tools?
I copied a Cisco 5510 startup-config to an identical Cisco 5510.After copying through tftp, I executed a reload. Everything looks good. Line by line compare results are the same.The problem is I can no longer use ASDM or ssh to interface with Cisco 5510.
View 25 Replies View RelatedI was able to connect to my ASA 5510 with a browser, install ASDM, and configure my ASA 5510 with my Windows 7 laptop. Since I needed the laptop for another task, I am now trying to connect using a Linux laptop to do the same, but without success.
I can ssh into the firewall using the management port (192.168.1.1) from the Linux command line. However, I cannot connect using a browswer (192.168.1.1) to install ASDM.
When i tried to login through ASDM at Cisco ASA 5510, it ask for the username and password and after that nothing comes up. I am able to login through ssh. [code]
As per my knowledge show bootvar and show version, should shows the same IOS version. But here it's showing different. Is asdm-523 is compatible with IOS asa708.
Is there a way to create an account for the ASA using ASDM that is only read only and cannot make firewall changes?
View 1 Replies View Relatedi have an issue with ASA 5510.
I connect to the device - https:/interface
I see the options such as download launcher etc.
But.. whenever I click on this I get stuck
Internet Explorer gives "page not found"
Or at the foot of the page it says "unable to download statup_lr"
Firefox says cannot connect
It is running 6.2.5.53
I can connect if I go to a PC where I have already downloaded the ASDM launcher (from many years ago)
Tried Win 2003, 2008 and Vista, and Windows 7
Tried downgrading to Java 6 r 7. Can I download the launcher from the Cisco website rather than the device? If so where?
On our ASA 5510 we have two security contexts. After opening ASDM I can see and manage admin context, but cannot see second context. I can do changes to second context via CLI but as probably you know it's easier and quicker doing it via ASDM.
View 7 Replies View RelatedI've recently switched to an ASA 5510 on 8.4(3) coming from a Checkpoint NGX platform (let's say fairly quickly and without much warning ). I have a couple questions and they're kind of similar so I'll post them up. I've read docs about regex and creating them both via command line and ASDM, but the examples always seem to include info I don't need or honestly something I don't understand yet (mainly related to defining classinspect maps). If someone could provide a simple example of how to do these in ASDM that would be useful in understanding how regular expressions are properly configured. So here we go.
I know this is basic but I need to make sure I understand this properly - I have a single web server (so this won't be a global policy) where I need to allow access to a specific URL pathfile and that's it. So we'll call it est estfile.doc. Any other access to any other path should be dropped. What's the best way to do this in ASDM (6.4)? I think if I saw a basic example for this I could figure out next few questions but I'll post them as well just in case.
I have another single public web server (again this won't be a global policy) where I'd like to specify blocking file types, like .php, .exe., etc... again a basic example would be great.
Lastly, and this is kind of related, but we have a single office/domain and sometimes we get spam from forged addresses appearing to be from our domain. On Checkpoint I used to use its built-in SMTP security server and could define if it received mail from *@mydomain.com to drop it because we would never receive mail externally from our own domain name. I saw something similar with ESMTP in ASDM and it looks kind of like how you set up the URL access mentioned above. Can I configure this in ASDM as well, and if so how?
I have purchased a Cisco ASA 5510 & want to block all social networking websites (https) either using CLI or ASDM.
View 1 Replies View Relatedi configurated Ipsec vpn at asa 5510.
my inside ip 192.168.10.156
my public ip: 85.x.x.x
my peer ip : 62.x.x.x
the project is that:the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
my inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.i do that way but i can not test it.
interface Ethernet0/0
nameif outside
security-level 0
ip address 85.x.x.x.106 255.255.255.248 standby 85.132.71.107
!
[code]....
The ASA 5510 is working with asa8.3.1 and asdm 6.3.1. ( with factory default config )i ve upgraded to asa8.4.1 and asdm 6.4.1.Now the asdm launcher is frozen after username/password. The asdm upload the software and write that "software update completed".After it the hour glass or sand-glass is visible over the asdm window.
View 2 Replies View RelatedI am attempting to block outbound traffic for a specific PC on my LAN using the ASDM.
View 2 Replies View RelatedI have a new ASA 5510 running 8.3(1) and ASDM 6.4(5)
I am trying to use the real time log viewer to troubleshoot some access issues, but I am getting delays of up to 30 seconds or more between my client connecting to the ASA and the corresponding events showing in the RT Log viewer. I am using a simple filter for source IP as it's quite a busy device.
I've seen an article that says to turn off certain logging IDs (such as 304001 from memory) which I have done, but no different.
In my Cisco ASA 5510 in release 8.2, I have an extrage behavior in the output of "show service-police" command. The issue is that I create a class-map to limit trafic in one of ASA interfaces and I applied in a service policy. This is the configuration:
access-list ACL-Limitada extended permit ip host srv-proxy any
access-list ACL-Limitada extended permit ip any host srv-proxy
access-list ACL-Limitada extended permit tcp 192.168.10.0 255.255.255.0 any eq ftp-data
access-list ACL-Limitada extended permit tcp 192.168.10.0 255.255.255.0 any eq ftp
access-list ACL-Limitada extended permit tcp any 192.168.10.0 255.255.255.0 eq ftp-data
access-list ACL-Limitada extended permit tcp any 192.168.10.0 255.255.255.0 eq ftp
[code]...
I am trying to see what traffic goes through a certain ACL so I specify a protocol instead of allow all IP traffic. So what I did is enabled logging with debugging on that ACL. When I right click on the ACL and show log, nothing shows up. But I see hits on the ACL.
View 1 Replies View Related