Cisco :: Is Temperature Monitoring Via Snmp Supported On 2801 Routers
Jun 19, 2012Is temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies
ADVERTISEMENT
Cisco :: Monitor Routers 2610 / 2801 And 1760 With Monitoring Software Called Zenoss?
Sep 4, 2011I am trying to monitor routers Cisco 2610, 2801 and 1760 with a monitoring software called zenoss. and I cant see on this devices the powersupply state, temperature sensor, fan state, i dont know if this models of routers cant support the monitoring of this component on the devices.what can i do to monitoring this component? what kind of Oid I can use to get this components state?
View 4 Replies View RelatedCisco :: MIB For Monitoring Temperature On 800
Sep 17, 2012if there is a MIB for monitoring temperature on a Cisco 800?
View 2 Replies View RelatedCisco WAN :: Monitoring Temperature On 1921 Router?
Feb 9, 2012how do I monitor temperature of my 1921 router? Which commands do I need to put on router and which MIBs to use. I am using PRTG network monitor as a monitoring system.
View 10 Replies View RelatedCisco WAN :: 2801 Router Not Showing Temperature In Show Environment All
Jun 19, 2012We have a Cisco 2801 router running IOS "c2801-spservicesk9-mz.151-4.M4.bin" which we upgraded from previous “c2801-spservicesk9-mz.124-3d.bin”.
Requirement.
We want to monitor the device temperature via snmp but unable to do because temperature ratings are not available on "show environment all" output like below.
Routeri# sh environment all Fan 1 OK Fan 2 OK ILP Power Supply - Absent Fan Speed Setting: Normal
Where as on Cisco 2811/51 & Cisco 3825/45 we can get temperature ratings on "show env all" output.
As per link [URL] below commands are supported on Cisco 2800 series router.
Command options
• show environment all
• show environment fans
• show environment leds
• show environment power-supply
• show environment table
• show environment temperatures
• show environment voltages
I want to know whether this is Cisco 2801 platform limitations or something else. tried to find Cisco doc on this but no luck.
Server Room - Remote Monitoring Temperature?
Jun 8, 2012Any temperature monitoring unit we can install in our server room that we can use to moniter the room temperature? We had a near catastrophe recently when the air conditioning unit failed to restart following a power outage.
View 3 Replies View RelatedCisco :: 3560 - Need SNMP OID Or Object Name To Monitor Temperature
Jul 28, 2011i have 3560 switch located in warehouse environments . i need to monitor the temperate of this switch . i am looking for OID value that serves this purpose .
kindly provide me how to look for all OID that give me real time status for FAN .. CPU UTILIZATION ...TEMPERATURE ...OR ANY MAJOR EVENT THAT CAN DISRUPT MY PRODUCT IN .
Cisco :: Nexus 5000 SNMP Monitor For Temperature Status
Aug 15, 2012May I know how to monitor temperature status of below device by SNMP.How to find the exact oid of those devices? I can only find the mib file of Nexus 5000 at url...Cisco Nexus 5010PCisco UCS 6120XP Cisco ASR 1002F
View 1 Replies View RelatedCisco Infrastructure :: Temperature Status From 2960 Switch Using SNMP Not Working
Sep 18, 2012WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
Cisco WAN :: HWIC-2CE1T1-PRI Not Supported On 2801 Router?
Jun 18, 2012The HWIC-2CE1T1-PRI card isn't supported on a CISCO2801 router
View 7 Replies View RelatedCisco VPN :: ASA5505 Remote SNMP Monitoring Over VPN
Apr 3, 2012We currently have a few 5505s installed at client sites which are connected via s2s ipsec VPN to our datacenter's 5510. We are using Nagios to monitor the local data center and remote client infrastructure (over the VPNs) which has been working well.
We would like to also monitor the remote 5505s using SNMP over the s2s tunnels but it doesn't seem to be working, the connection is timing out. We've configured the remote 5505s with the same snmp statement we used on the 5510 (snmp-server host inside <remote datacenter IP> poll community ***** version 2c) yet the Nagios SNMP check cannot connect to the remote 5505s. We've also tried the command using 'outside' without any luck, not sure how to get SNMP to route over the VPN.
Cisco :: SNMP OID For Monitoring CPU On Aironet 1252
Jan 27, 2013I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: ACS 1121 With 5.3 MIB For SNMP Monitoring
Mar 26, 2012I am trying to add ACS 1121 (ver 5.3) to monitoring and seems that MIB are missing. Need MIB for this device which I can use in monitoring tool.
View 1 Replies View RelatedCisco :: WLC 5508 / Individual AP SNMP Monitoring?
Jun 15, 2011 how snmp monitoring works when we have WLC in the networking.Before the WLC 5508 instalation, we had the Nagios monitoring each Access Point in the networking. Today, the Nagios still monitoring the networking, but the Nagios cannot get the same information of the APs (CPU, status interface, memory, etc).Now, the WLC controls each AP, the IP address, netmask, community (of all AP) are the same before the WLC instalation. I have tried to configure the SNMP information in Management>>SNMP>>Communities, but these configuration are from WLC and not from each AP.
How can I configure the SNMP setting in my AP to still use the Nagios to monitoring the networking?
Cisco AAA/Identity/Nac :: Monitoring ACS 1121 Via SNMP?
Aug 13, 2012I have 5 installations of ACS appliances (ACS 1121 running ACS 5.3). Is there a way to monitor them via SNMP? The AD client keeps dying on one of them, and even with the newest patch it's not up. Also, i want to monitor them up/down, CPU, memory... basic network monitoring to make sure my devices are healthy.
Any one know if that can be configured? I figured i'd ask here before opening a TAC.
Cisco :: 3750 SNMP Stack Monitoring?
Oct 3, 2006I am building a few 3750 stacks, I want to be able to poll/monitor each individual switch in the stack but as it only has 1 ip associated with the stack how can I do this. I am polling the uplink interfaces but as I only have uplinks on the top and bottom switch I am blind to a switch going down in the middle of the stack.
View 4 Replies View RelatedCisco :: Monitoring Catalyst 3560 Health Using MIB / SNMP
May 23, 2011I'm a C# programmer and as part of my software I need to monitor some Cisco Catalyst 3560V2 24 switches using SNMP (By reading MIB/S data).Apparently this switch supports more than 50 different MIBs.My question is which MIB/MIBS contains general health data (parameters) that may determine if the switch is OK, Degraded or Malfunctioned.
View 0 Replies View RelatedCisco Firewall :: ASA 5505 / SNMP Monitoring Over VPN Tunnel?
Mar 27, 2008I am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
View 2 Replies View RelatedCisco Switches :: SG300 Optical Monitoring Snmp-mib?
Apr 10, 2012I was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
Cisco Switching/Routing :: 6509 - VSS SNMP Monitoring
Oct 21, 2012I have two 6509E's configured with VSS. In this configuration, is it possible to monitor the CPU and memory of each switch independently using SNMP?
View 1 Replies View RelatedCisco :: 6500 - Monitoring IPv6 BGP Peers Via SNMP
Nov 5, 2011I'm running 12.2(33)SXJ1 on a 6500 with several IPv6 BGP peers. Is there any way to monitor the BGP status of IPv6 peers? I've been through the BGP4 mib and cant seem find a way to check the status of IPv6 peers.
View 4 Replies View RelatedCisco :: Digital Optical Monitoring Transceiver SNMP C7206VXR
Feb 5, 2012We have C7206VXR NPE-G2 platform with transceiver which support DOM.Could we monitor DOM tx/rx level statistic through snmp for 7206 platform?In CLI result of command "sh interf GigabitEthernet0/1 transceiver" give some information.We tried search for some MIB In "MIB locator" on cisco.com.
View 2 Replies View RelatedCisco Firewall :: ASA 5510 - Enable SNMP For Bandwidth Monitoring Using PRTG?
May 1, 2012I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies View RelatedCisco Firewall :: ASA 5510 Monitoring Loses SNMP Connectivity With SCOM 2012
Apr 4, 2013I'm currently implementing Microsoft System Center 2012 Operations Manager, the curent stage of the project is to add the network devices to SCOM via SNMP in order to monitor them, I am able to add them all and monitor; however, my ASA 5510, although SCOM discovers the ASA via SNMP and adds it to the network monitoring list, it loses SNMP connectivy every 30 minutes, and 15 later it reconnect with SCOM, then after another 15 minutes it loses the connection again, and so on and so for.
View 1 Replies View RelatedCisco :: 5500 - SNMP Operation To Device Failed / Sparse Table Not Supported
May 29, 2013I am currently running WCS 7.0.230 I have controllers that are 2500 that are running 7.4.100.60?
My problem is that when I try to add my controller that is a Cisco 5500 running the same 7.4.100.60 I am getting the error SNMP operation to Device failed: Sparse table not supported. Verify that the WCS and WLC versions are compatible and try again.
I have double checked SNMP strings, IP Addressing and everything else I can think of. It just doesn't make sense that I can add a Controller with the same image but different hardware and no the other to the WCS server.
Cisco Firewall :: Monitoring ASA 5505 Firewall Active / Standby Pair Using SNMP?
Sep 7, 2011How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
Utilizing A Monitoring Software For Our Routers And Switches?
Mar 8, 2011I had an interesting issue utilizing a monitoring software for our routers and switches. The monitoring tool indicated a few switches were down, however was unable to ping or telnet into them from the computer I had the software installed on.
View 2 Replies View RelatedCisco Routers :: SRP541W Max Supported SIP Sessions?
May 9, 2013I am curious of the max supported SIP sessionf of the SRP500 series.
View 1 Replies View RelatedCisco VPN :: How Many SSL VPN Users Are Supported In 1921-SEC/K9 Routers
Oct 18, 2011how many SSL VPN Users are supported in Cisco1921-SEC/K9 routers? Or do i need to separately purchase SSL-VPN User license- FL-SSLVPN25-K9 (Cisco SSLVPN Feature License-25 Users) separately?
My client requires 25 Users SSL VPN.
Cisco :: How Many SDR (Secure Domain Routers) Supported On ASR900
Mar 11, 2013How many SDR (Secure Domain Routers) supported on ASR9001?
View 1 Replies View RelatedCisco WAN :: How Many Ipsec Tunnels Are Supported In 3900 Routers
Jul 30, 2011How many ipsec tunnels are supported in Cisco 3900 routers(with & without the hardware processors)?How much is the throughput of the 3900 routers?
View 1 Replies View RelatedCisco Routers :: Is L2TP Over IPSEC VPN Supported In SRP 521w
Mar 26, 2013i am now trying to configure a Cisco Small Business Pro SRP 521w router for a branch office, i am trying to get the router to connect to a L2TP VPN server inside my datacenter, but seems to me like L2TP VPN client function is not supported inside the SRP 521w router.
Can Cisco implement L2TP VPN client into the firmware for the SRP 521w router in the future ?
Cisco Routers :: 527W-U Routed Subnet / Is One-to-one NAT Supported
Jan 15, 2013we are trying to configure one to one NAT translations on a Cisco 527W-U, but are having some problems. We are running firmware version 1.2.4 (003) on the 527.
The DSL line is assigned with a /29 address range x.x.x.64 /29?
The DSL WAN interface picks up x.x.x.65 /32 from the Radius server. We are using the default private IP address range 192.168.15.0 /24 on the LAN (VLAN1), and can get to the internet ok with a PC connected to the LAN.
However when we try to set up a public IP address in the same range (eg x.x.x.66 /29) on VLAN1 (with x.x.x.67 on the PC) it will not connect. (won't allow us to configure an address from the same range as the WAN on a new VLAN interface).
we would want to be able to do one to one NAT translations eg x.x.x.66 on the outside to 192.168.15.2 inside, x.x.x.67 outside to 192.168.15.3 inside etc, but this will not either. We have tried this on a normal IOS router (887) and it worked ok. We have also tried the same on a small DSL router / modem product similar to the 527 from another manufacturer and it worked ok on that, but we wanted it to be able to work on the 527.
We have tried the NAT bypass feature without any success, reading several other discussion forums on this website leads me to believe that one to one NAT is not supported on this equipment at the moment, or at least not at the current firmware release.
One work around would be to just assign a /32 to the WAN interface on the DSL and route statically to a different routed subnet configured on the LAN, however we were wanting to avoid having to do that if possible.