May I know how to monitor temperature status of below device by SNMP.How to find the exact oid of those devices? I can only find the mib file of Nexus 5000 at url...Cisco Nexus 5010PCisco UCS 6120XP Cisco ASR 1002F
View 1 Repliesi have 3560 switch located in warehouse environments . i need to monitor the temperate of this switch . i am looking for OID value that serves this purpose .
kindly provide me how to look for all OID that give me real time status for FAN .. CPU UTILIZATION ...TEMPERATURE ...OR ANY MAJOR EVENT THAT CAN DISRUPT MY PRODUCT IN .
WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies View Relatedwhat is the OID for See the hit status of the spefic VIP and RIP coming under the VIP .apeart from this CSS box having any module to moniter the hit status or VIP's and RIP's
View 2 Replies View Relatedtried to read the NEXUS 5000 cpu load: cseSysCPUUtilization 1.3.6.1.4.1.9.9.305.1.1.1 but there is a timeout: Timeout: No Response from 10.100.224.16 Other MIB values readout, like the system value, is ok.We use snmpv3.
View 4 Replies View RelatedIam having some issue trying to configure snmp-server context vrf XXX.From some reason even if i put my VRF name i cant see anything about this vrfthis is the command i add:
snmp-server context def vrf datacenter
What is the correct way to create an SNMP user on a Nexus 5k Switches and limit the read/write access to some OIDs?I have been searching for hours for configuration examples or guides, but i had no luck.I guess a role has to be created, containing rules for some feature, but the list of features doesn't contain anything about snmp.This is my configuration on catalyst switches and i'd like to achieve the same result on the Nexus 5k:
conf term
access-list 10 permit host x.x.x.x
access-list 10 deny any
snmp-server view myview ccCopyTable included
snmp-server group mygroup v3 priv read myview write myview access 10
snmp-server user myuser mygroup v3 auth md5 xxxxxx priv aes 256 xxxxxx
end
I'm looking for temperature monitor (HDD, CPU) that can be run with parameters, and have cmd result output.I need some software to monitor temperature in Labtech software.
View 12 Replies View RelatedI have load CISCO-ENVMON-MIB and initiate walk in it but unable to find OID of Cisco 2960 temperature monitor. I have search over net and found .1.3.6.1.4.1.9.9.13.1.3.1.3.1 for temperature but this OID is not responding in this mib.
View 2 Replies View RelatedIs temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies View RelatedI need to know how is the ambient temperature for the Nexus 7000 switches to plan a new datacenter. In the datasheet I found the following information regarding this topic:"GR-63-CORE Network Equipment Building Standards (NEBS) specification published by Telcordia Technologies in Section 4.1.2". How are the specification for temperature in this standard?
View 1 Replies View RelatedThe internet connection at our business goes down overnight, every night. We then have to turn off the router and turn it back on. It is not the fault of the ISP, but some setting somewhere, either in the router (SG 310 Snapgear) or in a particular program being accessed each night. Fact is, for the time being we are just trying to find out the precise time when this happens, so we can find out a reason. Is there a utility that can monitor the status and tell you at what exact point it stopped?
View 2 Replies View RelatedWe have a Cisco ASA 5520 in HA (Active - Standby). We monitor the CPU,Memory Utilization and Active Session via SNMP polling.And SNMP trap for linkup ,linkdown and Cold start.Our requirement is to monitor the HA status and whenever there is a change in the HA - Failover we have to get a snmp trap.What are the configuration need to be done on the cisco asa.
View 3 Replies View RelatedDoes Cisco 3750 ip sla can monitor, let's say, monitor 3750 G1/0/1 port status, once it is down, then 3750 also make G1/0/2 also down. If yes, what is the command to do it?
View 3 Replies View Relatedrequesting information via SNMP from my two stacked C3750X, running IOS 12.2(55)RE5. The stack is up and running and everything is just fine. There are three PowerSupplies installed with a PowerStack, also running like expectet.My problem ist to get the status-information about the chassis-fans. I couldn't find any information about the OID and the search results only in some non-useful information about the MIBs from Cisco which delivers only three information about installed fans (and fan-containers), so I guess these are the information about the fans included within the powersupply?! The chassis-fans are installed and the LEDs are green for all four fan-mounts, up and running.
View 4 Replies View RelatedI have some questions about monitor of status of services on Network Devices such as HSRP, Etherchannel (between Access ports and Servers), etc. How we can track those information in addition to Syslog. Is it possible that the Fault Monitor displays them?
View 1 Replies View RelatedWe have a nexus 5k, and it kind of got hung today... it is running. Version 5.1(3)N2(1b) the reset reason shows.Power down due to temperature sensor policy trigger.It doesn't look documented. What policy is it referring to? not sure if this is an IOS bug ?
View 1 Replies View RelatedWe run 6509 core routers as NTP servers to other IOS routers/switches & servers of several OS flavours.All good. Recently added some Nexus 5000s and cannot get them to lock.No firewalls or ACLs in the path
6509 (1 of 4) state:
LNPSQ01CORR01>sh ntp ***
address ref clock st when poll reach delay offset disp+ 10.0.1.2 131.188.3.220 2 223 1024 377 0.5 -6.23 0.7+~130.149.17.21 .PPS. 1 885 1024 377 33.7 -0.26 0.8*~138.96.64.10 .GPS. 1 680 1024 377 22.7 -2.15 1.0+~129.6.15.29 .ACTS. 1 720 1024 377 84.9 -3.37 0.6+~129.6.15.28 .ACTS. 1 855 1024 377 84.8 -3.30 2.3 * master (synced), # master (unsynced), + selected, - candidate, ~ configured
[code]....
Are we missing some NTP or managment vrf setup in the Nexus 5Ks?
I need to implement a "Spanning Tree Status" view on my NMS and I would like to use SNMP. I'm running Rapid Per-VLAN Spanning Tree Protocol on 3560-E (WS-C3560E-24TD) with IOS 12.2(55)SE.Using the ciscoStpExtensionsMIB MIB (CISCO-STP-EXTENSIONS-MIB) I see the stpxRSTPPortRoleTable table, which contains the stpxRSTPPortRoleValue value, and I think it could be fine for my job.The problem is that this table uses an index based on the standard dot1dBridge.1.4 table (dot1dBasePortTable) that does not report some interfaces: [code]I think the dot1dBasePortTable does not include those interfaces (5, 7, 8) where I do not run standard STP, but I need the dot1dBasePortEntry entries because I have to use them in order to get the interface ID (values like 10109, 10110, 10111).
View 0 Replies View RelatedI think I may have a bad port on a 5548, does the NX-OS has any sort of self-diagnostic test on its port?
View 6 Replies View RelatedI am looking how to see the mac table on a Nexus 5000 switch running NX-OS and confirm the mac address on a certain port. Similar to the Sh mac-address-table in IOS and sh cam in Cat-os.
I am sure this is simple I just cannot find the command.
Is it possible to disable mac learning on a specific vlan in the nexus 5000?
View 4 Replies View Relatedi have a use-case in which we need to firewall some of the security-sensitive-vlans to the ASA. In other words, there are few vlans that have their SVIs on the N5k (Layer-3 enabled) which talk to each other and there are some which have the layer-3 on the ASA. The ASA has sub-interfaces for those vlans. The N5k-sw and the ASA are interconnected on the same 1 physical link with a sub-interface on both ( /30) and the ASA is injecting default route to it in OSPF. They are advertising all of their networks in OSPF. I see all the routes in them. (Attached pic),My issue is: I am unable to ping the other sub-interface on the ASA from the N5k. (If you check the attached diagram, i cannot ping 20.1.1.1 from the N5k, although i can reach my next-hop 10.1.1.2) I have made the security-level to 100 for the subinterfaces and the physical interface on the ASA, also have allowed ip,icmps in the ACLs on the sub-interfaces of vlan 10 and 20 in both directions.
View 5 Replies View RelatedWe are using almost 10 Nexus 5k in our DC currently we are getting same error logs in all Nexus 5k." ntpd[4746]: ntp:time reset +0.279670 s " ,Is it major error or just for reset time?
View 1 Replies View RelatedIs is possible to monitor bandwidth utilization of a PAT on an ASA? We're running version 8.2.
View 1 Replies View RelatedAm new to Nexus switching, i have a Nexus box that i need to link with IBM servers with 10GB Network Cards.
how to set up fiber channel on this machine
I have a little problem. My customer is using TACP-PLUS ALPHA (F4.0.3.alpha.v9). Well, the same user than have access to another Cisco equipment, with user test1 by sample, can configure anything in the equipment. But in the nexus 5000, el command "show user-account" indicate just the "network-operator" role. Well, I patch this situation with the next commands:
aaa authorization config-commands default group TACSERVER local
aaa authorization commands default group TACSERVER local
Well, when I do a telnet into the nexus, I can shut the interfaces, config and anything. But, when I ingress by console, I can not to configure the interfaces.I understand that the Nexus 5000 the Tacacs configuration is global for VTY and Console (different in the Cisco equipment Routers by sample).
I have the following configured on my Nexus switches and works with success.
The problem I have is Once I switch of the ACS server I can log on to the Nexus as I have a admin user configured locally on the Nexus and the ACS server unfortunately can not run commands as it tries to point to the ACS server for auhtorization and the ACS server is turned off is it possible for the Nexus to ignore the authorization command if it can not see the ACS server ?
Feature tacacs+
ip tacacs source-interface vlan 705
tacacs-server host x.x.x.x key 7 "xxxxxx"
aaa group server tacacs+ Test-switch (Test-switch is a group configured on ACS 5.2)
[Code]...
Monitoring H.323? I've got a 3925 running15.1(3)T with 9 PRI's. Because of our volume, syslogging is not the desired solution. We want something that we can potentially graph over an 8 hour period, so while the RTMT is accurate, either it won't store the data for 8 hours, or we aren't using it correctly (plus, mgmt may want access to the stats/graphs, and we're not keen on granting them access). So far, we've used: [code] None of these seem to accurately portray utilization. cdsp Active Channels seems to get the closest, so perhaps I have to tweak it a little bit, but so far, nothing accurate.
View 3 Replies View RelatedAny opinion on what could cause loops on nexus 5000 ports that are connected to esx hosts ?
View 3 Replies View RelatedI'm planning to upgrade N5K from 5.1(3)N2(1b) to 5.2(1)N1(4)."sh install all impact kickstart bootflash:n5000-uk9-kickstart.5.2.1.N1.4.bin system bootflash:n5000-uk9.5.2.1.N1.4.bin"reports:
...
Compatibility check is done:
Module bootable Impact Install-type Reason
------ -------- -------------- ------------ ------
1 yes non-disruptive reset
...
Is the upgrade really non-disruptive?
I ma trying to query "CISCO-PORT-CHANNEL" mib on Nexus 7000 for portChannel table and I am not getting any info.
Nexus OS versions : Nexus 7000 - System version: 5.1(5)
Nuxus 5000 - System version: 5.0(3)N1(1a)
Any pointers or other alternatives to query through MIB ?