I'm running 12.2(33)SXJ1 on a 6500 with several IPv6 BGP peers. Is there any way to monitor the BGP status of IPv6 peers? I've been through the BGP4 mib and cant seem find a way to check the status of IPv6 peers.
View 4 RepliesWhat is the reason of following NTP error. I am unable to configure further ntp peers on the router. Could not able to understand the reason of 100 peers. I am adding only 2nd peer on the router but getting this error. There is no problem adding peers in other 6500s .
View 2 Replies View RelatedWe currently have a few 5505s installed at client sites which are connected via s2s ipsec VPN to our datacenter's 5510. We are using Nagios to monitor the local data center and remote client infrastructure (over the VPNs) which has been working well.
We would like to also monitor the remote 5505s using SNMP over the s2s tunnels but it doesn't seem to be working, the connection is timing out. We've configured the remote 5505s with the same snmp statement we used on the 5510 (snmp-server host inside <remote datacenter IP> poll community ***** version 2c) yet the Nagios SNMP check cannot connect to the remote 5505s. We've also tried the command using 'outside' without any luck, not sure how to get SNMP to route over the VPN.
I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies View RelatedI am trying to add ACS 1121 (ver 5.3) to monitoring and seems that MIB are missing. Need MIB for this device which I can use in monitoring tool.
View 1 Replies View Related how snmp monitoring works when we have WLC in the networking.Before the WLC 5508 instalation, we had the Nagios monitoring each Access Point in the networking. Today, the Nagios still monitoring the networking, but the Nagios cannot get the same information of the APs (CPU, status interface, memory, etc).Now, the WLC controls each AP, the IP address, netmask, community (of all AP) are the same before the WLC instalation. I have tried to configure the SNMP information in Management>>SNMP>>Communities, but these configuration are from WLC and not from each AP.
How can I configure the SNMP setting in my AP to still use the Nagios to monitoring the networking?
I have 5 installations of ACS appliances (ACS 1121 running ACS 5.3). Is there a way to monitor them via SNMP? The AD client keeps dying on one of them, and even with the newest patch it's not up. Also, i want to monitor them up/down, CPU, memory... basic network monitoring to make sure my devices are healthy.
Any one know if that can be configured? I figured i'd ask here before opening a TAC.
I am building a few 3750 stacks, I want to be able to poll/monitor each individual switch in the stack but as it only has 1 ip associated with the stack how can I do this. I am polling the uplink interfaces but as I only have uplinks on the top and bottom switch I am blind to a switch going down in the middle of the stack.
View 4 Replies View RelatedI'm a C# programmer and as part of my software I need to monitor some Cisco Catalyst 3560V2 24 switches using SNMP (By reading MIB/S data).Apparently this switch supports more than 50 different MIBs.My question is which MIB/MIBS contains general health data (parameters) that may determine if the switch is OK, Degraded or Malfunctioned.
View 0 Replies View RelatedI am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
View 2 Replies View RelatedI was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
I have two 6509E's configured with VSS. In this configuration, is it possible to monitor the CPU and memory of each switch independently using SNMP?
View 1 Replies View RelatedWe have C7206VXR NPE-G2 platform with transceiver which support DOM.Could we monitor DOM tx/rx level statistic through snmp for 7206 platform?In CLI result of command "sh interf GigabitEthernet0/1 transceiver" give some information.We tried search for some MIB In "MIB locator" on cisco.com.
View 2 Replies View RelatedIs temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies View RelatedI am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies View RelatedI recently picked up a Catalyst 2960G and am trying to get SNMP management working over IPv6. I have the IP Address set to the local link, and can successfully ping and telnet to the switch (so the network can get traffic to and from the switch). However, SNMP packets just seem to disappear. I am running WireShark on my machine, and I see the packets go out to the proper IP, but nothing comes back. When I check "sho ipv6 traffic", I can see where there are UDP packets that are received, but, again, none going out. Also, when I run "sho snmp", all of the packet counts are 0.
Here are some relavant snipets from my "sho run":
interface Vlan1
no ip address
no ip route-cache
ipv6 enable
[code]....
I'm currently implementing Microsoft System Center 2012 Operations Manager, the curent stage of the project is to add the network devices to SCOM via SNMP in order to monitor them, I am able to add them all and monitor; however, my ASA 5510, although SCOM discovers the ASA via SNMP and adds it to the network monitoring list, it loses SNMP connectivy every 30 minutes, and 15 later it reconnect with SCOM, then after another 15 minutes it loses the connection again, and so on and so for.
View 1 Replies View RelatedIm looking for MIB for monitoring 6500 line card from availability prespective;
View 1 Replies View RelatedI want to learn that,on cisco switch (2950,3600,6500 series) IpV6 default open? İf It comes open on default,how to disable?
View 19 Replies View RelatedA customer observes SNMP timeout problems on a Cat6500 with IOS 12.2(33)SXI. As a result every 2 days (more or less) all interfaces are marked DOWN and a couple of minutes later all interface are up again - but in fact there is no interruption, it is just the snmp request getting a time out. the customer does not have problems with IOS 12.2(18)SXF14.
In the Bug Details the "Known affected versions" lists the following beside others:
12.2(33)SXI
12.2(33)SXI1
12.2(33)SXI2
[code]...
Now I am confused; both IOS versions are listed as affected (12.2(33)SXI and 12.2(18)SXF14) but the customer does have problems only with one version. Is the customer hitting this bug or is it another one ?
He upgraded 2 Cat65xx on which he observed the problem to IOS 12.2(33)SXI6 and the problem is gone; is this just a coincidence or is CSCed52841 really fixed in 12.2(33)SXI6. This version is not listed as affected but on the other hand, "Fixed-In" lists only these 3:
12.1(22.3)E1
12.2(17d)SXB5
12.2(18)SXD
Before going to upgrade around 50 Core / Distribution switches the customer wants to be sure with the IOS version. Tracing the issue is not that easy because the failure occurs only from time to time.
I want run IPV6 multicast routing on Cisco 6506 device, I know i can activate IPv6 multicast routing globally but , Is it possible to run ipv6 multicast routing on interface vlan XXXX ?
View 1 Replies View RelatedHow I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
I would like to monitor the status of ether channel and trunk configurations in 6500 Catalyst switches running both CATOS and IOS. I would like to understand the specific mibs /OIDS that should be monitored for ether channels and trunks. I am trying to get a better handle on tracking the ether channels and trunk dynamically and then understanding when the ports are having issues (up/down and errors). I need to understand how to differentiate these type of ports from regular access ports.
View 4 Replies View RelatedIs it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View RelatedI have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies View RelatedI have a location where I have 2 WAN links, but without a dynamic routing protocol in between. I want to implement a kind of hub to 2 spokes VPN. But the spokes will actualy be on one single ASA firewall, each spoke on a different interface. One hub-spoke will be primary, the other one the secondary. When the WAN link for the primary VPN fails the secondary should be started on the hub to the other spoke.
View 1 Replies View RelatedHad a question regarding creating dial peers through sip trunks. It will be through verizon fios so it'll be terminated through the fa0/0 port. I know to the provider i'll implement something along the lines of this:dial-peer voice 1 voipsession target ipv4:1.2.4.4sipv2port fa0/0Many of the documentation I came across really only shows pots dial-peers will a voip dial-peer work the same? Something a long of the lines of this:dial-peer voice 2 voipdesination-pattern 91[2-9]..[2-]...... no digit-stripport fa0/0
View 9 Replies View RelatedI have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.
The Cisco ASA has the 50 internal user license with 10 VPN peers.
We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails.
Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences?
This seems to be the issue from what I can see, just need confirmation.
I am trying to get a 2811 to accept two IPSec peers however can only get one working at a time. I have setup fa0/0 and fa0/1 with their own public facing IP addresses with crypto maps associated to each interface however can only establish connectivity to one interface at any one time.
Relevent configuration below:
crypto isakmp policy 2
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
[code]....
I have one ASA with two tunnels. Each going to a different 3rd party Checkpoint firewall (site A, site B) Each site has two servers (A1, A2, B1, B2)I can only connect to A1 and B1. any connection to A2 and B2 fails. I have defined B2 and A2 in the crypto map to be protected.If I only have B2 or A2 in the crypto map ACL then the tunnel fails. Phase 1 does not come up. Its as if the ASA is ignoring the entries for B2 and A2.ASA running 8.4(2).I have also trashed the VPN and built via the wizard, same result.
View 12 Replies View RelatedAt our organisation our routers all have at least 3 BGP peers, each from a different connectivity provider. The different providers that we use all have different internet transit CDRs. Is there a way that I can configure a priority for the 3 BGP peers on our routers so that outbound traffic to the internet is sent to the BGP peer from the provider with the highest CDR?
Routers are C2821
I am imagining a smallish networking (AS1234) with say three full BGP table peers that provide transit to the network (just to keep the maths simple here); Lets say AS100 and AS200 are preferred transit providers with AS300 as a backup/least prefered (AS prepends or similar stop us from using this network by default). So in this scenario our little network gets two different paths across the Internet, as not to rely solely on one provided, with a backup provider to hand also.
How do you mange issues like packet loss somewhere in AS100's or AS200's network? So lets say a host on our AS1234 network is talking to host in AS888 and the preferred route is through AS100 but somewhere deep in AS100 a link is flapping (for example) and I can't get to AS888 reliably through there anymore, but I can through to other peers of AS100 OK. We can postulate that AS100 is the best path for 50% of the Internet and AS200 for the other 50% (this is a best case fictional scenario). I can't ping 50% of the internet via AS100 and then in the event a ping fails (or some other more reliable test) tear down the BGP session to use AS100 until it's fixed again, nor vice versa with AS200.
First of all, I asume you don't know about the issue between AS100 and AS888 until someome moans about it to you? Secondly, do you then some how modify the route(s) to AS888 that come from AS100 (route map for example to change the weight or preference) so AS200 is now preferred for AS888? Do you infact shut down the AS100 peering and now use AS200 & AS300? How do you rectify these situations that are beyond you control using what is in your control?
We have an ASA5520 configured with a IPSec VPN, from any ADSL home/office our VPN clients can connect without any problem, but when we use our cellular phones in tetering mode (as an accesspoint) our VPN clients are impossible to connect. Same machines,same software, same operating system, same remote IP (ASA5520 external IP) only change Wifi connection (ADSL to cellular phone). The signal of cellular phones is not the problem we was doing the tests with different phones (IPHONE & ANDROID), different locations (all in spain) and differents providers (vodafone, orange and movistar) of internet by cellular phone.We think that perhaps the problem is the licenses that our ASA5520 has..
Our ASA5520 comes with this licenses:
------------------------------------------------------------------------------------------
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 150 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
[code]....