Cisco :: 5500 - SNMP Operation To Device Failed / Sparse Table Not Supported
May 29, 2013
I am currently running WCS 7.0.230 I have controllers that are 2500 that are running 7.4.100.60?
My problem is that when I try to add my controller that is a Cisco 5500 running the same 7.4.100.60 I am getting the error SNMP operation to Device failed: Sparse table not supported. Verify that the WCS and WLC versions are compatible and try again.
I have double checked SNMP strings, IP Addressing and everything else I can think of. It just doesn't make sense that I can add a Controller with the same image but different hardware and no the other to the WCS server.
View 1 Replies
ADVERTISEMENT
Mar 4, 2012
after upgrading the firmware on the wireless lan controller 5.2.178.0 on my cisco 4402 wlc's and rebooted the devices, I am getting matches on the audit status between whats on the contoller and the wcs software. so i am trying to apply whats in the wcs templates created for the controller and i am getting this error.
SNMP operation to Device failed: Attempt to set conflicting attribute value
I am thinking that i need to rebooted the wlc's again because from the error it sounds like the values that i am trying to write to the controllers are already present
View 1 Replies
View Related
Nov 9, 2011
I am using LMS 4.0 and I keep encountering this issue "Error performing SNMP Operation"
View 5 Replies
View Related
Dec 13, 2011
I have a cat 3750 switch with the folowing snmp v3 config:
-snmp-server group admin v3 priv
-snmp-server user lmsadmin admin v3 auth md5 password1 priv aes 256 password2
The credentials on the device in LMS are as folowing:
where Auth. password = password1 and private password = password2:
When I run a credentials verification job, I get the following error message:
Error performing SNMP operation.
I have tried this on LMS version 4.0 and 4.1 with the same result.
View 2 Replies
View Related
Jun 1, 2010
i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
View 9 Replies
View Related
Nov 30, 2011
My BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies
View Related
Jan 26, 2010
trying to fetch the equivalent of the mac-address-table on a 1811 with SNMP. I want a mapping between active MACs to a port ifIndex (not a VLAN interface ifIndex).
- I've snmpwalked every MIBs on this device (including all the proprietary MIBs supported by the IOS)
- I've upgraded to latest IOS from the 12.4(24)T series and also tried latest from 12.4(15)T series
- I am aware of the community index (@ sign in read-only community to split per vlan)
- I've exhausted all my google skills
On 29xx, 35xx, we obtain that information using the BRIDGE-MIB, community indexing and the following OID:
1.3.6.1.2.1.17.4.3.1.2 (dot1dTpFdbPort)
ex:
# snmpwalk -v 2c -c public@1 192.168.1.61 1.3.6.1.2.1.17.4.3.1.2
SNMPv2-SMI::mib-2.17.4.3.1.2.0.23.89.208.164.62 = INTEGER: 24
SNMPv2-SMI::mib-2.17.4.3.1.2.0.23.101.255.67.177 = INTEGER: 12
SNMPv2-SMI::mib-2.17.4.3.1.2.0.24.25.113.78.52 = INTEGER: 11
View 4 Replies
View Related
Jan 23, 2012
I'm looking for a SNMP set command that clear the MAC Address table on a Switch Cisco 4503.
View 3 Replies
View Related
Jan 3, 2013
We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies
View Related
Jun 19, 2012
Is temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies
View Related
May 5, 2013
I am looking for a reference document for the type of devices that are supported under 5Ghz. We are using a 5500 WLC and 3600 WAPs. Lot of users cannot connect to network via mobile devices. Is there a reference doc from cisco which i can use to inform them?
View 5 Replies
View Related
Aug 31, 2012
On a 5500 series WLC I see I have an issue where peap clients get randomly disconnected with these errors
MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client 24:77:03:35:79:34
AAA-6-ARP_LOOKUP_FAIL: radius_db.c:3232 Default gateway arp lookup failed.
aaaQueueReader: Aug 31 19:12:14.938: %AAA-4-RADIUSMSG_SEND_FAILED: radius_db.c:3567 Unable to send RADIUS message to
View 7 Replies
View Related
May 22, 2012
I'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
View 1 Replies
View Related
Nov 11, 2012
I restored the HA pair back to Active/Standby.
1 remaining issue.
I have 3 IPsec Site-to_SIte tunnels.
I noticed that when the NEW UNIT becomes ACTIVE that I am unable to pass traffic over the VPN tunnels.When I failback I am able to pass traffic.
View 7 Replies
View Related
May 10, 2012
A new Cisco 3750V2 (WS-C3750V2-48PS-S) running IOS 'c3750-ipbasek9-mz.122-50.SE5.bin' waspurchased to add to a stack of 3 Cisco 3750 (WS- C3750- 48PS-S) switches. The IOS on the stacked switches is 'c3750-ipbase-mz.122-25.SEB4.bin'.I loaded this IOS on to the new Cisco 3750V2 and deleted its original IOS. Boot up failed with error 'hardware not supported by firmware'. I am now trying to follow the recovery procedure but the I can only initialise the flash (flash_init) and there is no 'boot_helper' command to load the boot helper files. There is no option to rum 'copy xmodem' so I cannot upload the original IOS image via xmodem on hyperterminal.
View 7 Replies
View Related
Jan 10, 2011
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Jan 20, 2013
I have problems with setting the snmp retry / timeout parameters for our devices. I managed to import our devices with bulk import , but after it I realized that for some devices the snmp retry / timeout values were different ( created the bulk file with 3 retries and 30 sec timeout , but in the system the appear with 2 retries and 1 sec timeout). I tried to change it manually , but after a while it goes back to the wrong values.
View 1 Replies
View Related
Nov 15, 2011
Okay so currently in my possession is a SR 5500 wireless channel receiver with a problem.. We need to find its current ip address it also is not a standard ip address such as 192.168.xxx.xxx it has a standard ethernet port and of course GPIB ports
I'm looking to know if there is a way I can find its ip address by maybe with a crossover cable, or by bridging its connection to my computer and somehow seeing what ip it's requesting.
View 1 Replies
View Related
Dec 16, 2011
I'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router. I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware. I get the message "A non-supported device is connected to your router's USB port. Disconnect that device and follow the steps below to connect a USB printer to your router." Cisco support was not beneficial.
View 1 Replies
View Related
Aug 16, 2011
i get for all devices telnet credential failed in my credential verification report. I exported the device from the Device Manager into a csv file to verify the correct passwords.The export shows the correct values in
<DEVATTRIB Name="primary_username">cwuser</DEVATTRIB>
<DEVATTRIB Name="primary_password">secretpassword</DEVATTRIB>
View 4 Replies
View Related
Nov 16, 2011
Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies
View Related
May 10, 2012
I am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
View 9 Replies
View Related
Mar 15, 2011
Does any know the meaning of this log message in a 7609 router - "SP: FAILED to write to DS1338 RTC device"?
So far as I can tell DS1338 RTC is supposed to be a (linux-related?) clock but I don't see how that's related to the.
View 7 Replies
View Related
Apr 24, 2013
I add 4510 and 4507 in zhe LMS ,but fault discovery failure.
View 7 Replies
View Related
Apr 15, 2010
I try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
View 11 Replies
View Related
Apr 7, 2011
I am trying image distribution to a c3560 device but I always get the error message SWIM1164. In the documentation it says to copy the logs and open a TAC Case but I would like to do some troubleshooting myself before opening a case.
Some actions to be taken prior to opening a case?
[code]...
View 8 Replies
View Related
May 9, 2012
This is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.
I increased SNMP timeout to 10 seconds to no avail.
View 5 Replies
View Related
Sep 14, 2012
I just reinstalled my Inspiron 1720 and everything works fine but the Bluetooth Peripheral Device which keeps reinstalling after every reboot.
In device manager Bluetooth Radios, "Dell Truemobile 355 Bluetooth + EDR" and "Microsoft Bluetooth Enumerator" are installed properly but I have in "Other devices" a Bluetooth Peripheral Device which does not want to install.
I used Driver CD provided when I purchased my laptop but it does not find any drivers to solve the problem. I also went to dell.com drivers to fin the latest one and this neither does not work .
View 2 Replies
View Related
Jan 26, 2012
We are using Catalyst 3750 switch stacks with software 12.2(44)SE. We have two stacks, only one with IP routing enabled.When we try to run an Acquisition Action on this, from Admin> Collection Settings> User Tracking, the system replies with an error "Failed to start acquisition: Device unreachable. Please enter a valid device"device Center reports "success" on all collector status.Acquisition starts successfully when we try with the other stack.With LMS 4.1 demo, users acquisition runs successfully.
View 18 Replies
View Related
May 30, 2013
I am using ISE 1.1.1.268 and WLC 7.2.111.3 and NAC agent version 4.9.1.6 on Windows 7 Client machines.
About once a day i get the error "ISE Alarm (WARNING): Dynamic Authorization Failed for Device".
The device it is referring to is my NAD, a WLC 5508 running 7.2.111.3
I have looked at the logs and I cannot see anything in the logs which corresponds to this message so that I can troubleshoot further. Maybe I can if I am enabling the correct logging level on the correct ISE component.
What are the components and the logging level that I should set to get some more detail about this error?
At the moment, I have only set debug logging on Active Directory. I have TRACE logging set on Posture, Run time AAA & prrt-JNI.
I do not want to enable too much debug logs, so what is the specific element that I should be debugging.
I thought debugging the posture element would be enough but when I look at the logs there is nothing there that relates to this message.
View 3 Replies
View Related
Jan 16, 2013
In datasheet of WS-SUP720-3B - link- was said that are only supported around 256K routes (fib?rib?).With this value I can't get 2 full bgp - that is around 850K ..
The supervisor is that control this or just memory ? I said this because I have a 7204-npe-g1 whith 2 fullrouting and 1G of and he are ok..
View 3 Replies
View Related
Jan 15, 2012
The installation of an ACE-4710 throughput upgrade license licence (ACE-AP-02-UP1) failed with an error message :CH01AC03/Admin# license install disk0:ACE20111213081741975.lic.Installing license... failed: No space left on device. [code]
View 4 Replies
View Related
