i get for all devices telnet credential failed in my credential verification report. I exported the device from the Device Manager into a csv file to verify the correct passwords.The export shows the correct values in
<DEVATTRIB Name="primary_username">cwuser</DEVATTRIB>
<DEVATTRIB Name="primary_password">secretpassword</DEVATTRIB>
when running Credential Verification Report, I get following notification: "None of the devices have credential verification data".I have made different Default Device Credential sets that I'm using when I add devices to LMS. I could not see wether this is bug in LMS 4.1 or if I have to do this a different way?
View 1 Replies View RelatedI recently installed and configured the Prime LMS 4.1 Soft Appliance. After discovering the devices on the network I ran a credential verification check on everything. All of my devices passed accept for the Nexus 7010s and Nexus 5020s -- these show up in the failed device report with a BLANK value for SSH and "Did Not Try" under Enable by SSH. I have verified SSH is enabled and accessible outside of Prime, and that there are no access lists preventing access. All other tests pass for these devices.
I've also visited the troubleshooting workflow section for these devices, and when I test the connectivity, SSHv2 passes.
I've downloaded all of the updates available for the device packages and have tried other credentials. All other aspects seem to be working properly.
I am trying to install a digi cert on a 7921 and I get the message on import of "certificate verification failed".as there does not seem to be much documentation with the above error message.
View 2 Replies View RelatedI'm trying to troubleshoot a problem with mpls fast reroute. The primary (protected) link is between PE-PE and the backup link is PE-P-PE. The IGP I'm using is OSPF. When there is a issue with the primary link and debug mpls tra tunnels signalling there is a message "LSP-TUNNEL-SIG: TunnelX [237]: re-route path verification failed (protected) [Can't use link x.x.x.x on node x.x.x.x]". After 30 seconds (without ospf tuning) the SPF is recalcalated, but that's not the point From the show mpls tra tunnels tu1013 (the backup one)everything looks ok:
Status:Admin: up Oper: up Path: valid Signalling: connected From show mpls tra fast-reroute database everything is ok, the status is Ready I'm using 7206VXR, Version 12.4(24)T3
I have a case for an LMS 4.0 running in a Live environement (With devices already discovered and organized into seperate groups), where the Device Credential and repository DCR is showing suddenly as empty and only i can see the groups listed, but without any devices in them (Through Inventory > Device Administration > Add/Import/Manage Devices).After a restart of the whole LMS server a few weeks ago, the problem was fixed and the devices appeared again, but now the same issue re-appeared.
View 5 Replies View RelatedI have a problem when doing this report. If I do a device credentials report on a user defined group (40 devices) 11 of these devices fails to connect via SSH. I can make an SSH connection to all 11 devices from the CiscoWorks server, but 11 devices still fails on the report
Device Name Read Community Read Write Community SSH
1. 149.212.XXX.164 Ok Ok Failed to connect.
2. 149.212.XXX.153 Ok Ok Failed to connect.
3. 149.212.XXX.152 Ok Ok Failed to connect.
4. 149.212.XXX.151 Ok Ok Failed to connect.
5. 149.212.XXX.150 Ok Ok Failed to connect.
[code]....
We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedI am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
Does any know the meaning of this log message in a 7609 router - "SP: FAILED to write to DS1338 RTC device"?
So far as I can tell DS1338 RTC is supposed to be a (linux-related?) clock but I don't see how that's related to the.
I add 4510 and 4507 in zhe LMS ,but fault discovery failure.
View 7 Replies View RelatedI try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
after upgrading the firmware on the wireless lan controller 5.2.178.0 on my cisco 4402 wlc's and rebooted the devices, I am getting matches on the audit status between whats on the contoller and the wcs software. so i am trying to apply whats in the wcs templates created for the controller and i am getting this error.
SNMP operation to Device failed: Attempt to set conflicting attribute value
I am thinking that i need to rebooted the wlc's again because from the error it sounds like the values that i am trying to write to the controllers are already present
I am trying image distribution to a c3560 device but I always get the error message SWIM1164. In the documentation it says to copy the logs and open a TAC Case but I would like to do some troubleshooting myself before opening a case.
Some actions to be taken prior to opening a case?
[code]...
This is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.
I increased SNMP timeout to 10 seconds to no avail.
I just reinstalled my Inspiron 1720 and everything works fine but the Bluetooth Peripheral Device which keeps reinstalling after every reboot.
In device manager Bluetooth Radios, "Dell Truemobile 355 Bluetooth + EDR" and "Microsoft Bluetooth Enumerator" are installed properly but I have in "Other devices" a Bluetooth Peripheral Device which does not want to install.
I used Driver CD provided when I purchased my laptop but it does not find any drivers to solve the problem. I also went to dell.com drivers to fin the latest one and this neither does not work .
We are using Catalyst 3750 switch stacks with software 12.2(44)SE. We have two stacks, only one with IP routing enabled.When we try to run an Acquisition Action on this, from Admin> Collection Settings> User Tracking, the system replies with an error "Failed to start acquisition: Device unreachable. Please enter a valid device"device Center reports "success" on all collector status.Acquisition starts successfully when we try with the other stack.With LMS 4.1 demo, users acquisition runs successfully.
View 18 Replies View RelatedI am using ISE 1.1.1.268 and WLC 7.2.111.3 and NAC agent version 4.9.1.6 on Windows 7 Client machines.
About once a day i get the error "ISE Alarm (WARNING): Dynamic Authorization Failed for Device".
The device it is referring to is my NAD, a WLC 5508 running 7.2.111.3
I have looked at the logs and I cannot see anything in the logs which corresponds to this message so that I can troubleshoot further. Maybe I can if I am enabling the correct logging level on the correct ISE component.
What are the components and the logging level that I should set to get some more detail about this error?
At the moment, I have only set debug logging on Active Directory. I have TRACE logging set on Posture, Run time AAA & prrt-JNI.
I do not want to enable too much debug logs, so what is the specific element that I should be debugging.
I thought debugging the posture element would be enough but when I look at the logs there is nothing there that relates to this message.
The installation of an ACE-4710 throughput upgrade license licence (ACE-AP-02-UP1) failed with an error message :CH01AC03/Admin# license install disk0:ACE20111213081741975.lic.Installing license... failed: No space left on device. [code]
View 4 Replies View RelatedI am currently running WCS 7.0.230 I have controllers that are 2500 that are running 7.4.100.60?
My problem is that when I try to add my controller that is a Cisco 5500 running the same 7.4.100.60 I am getting the error SNMP operation to Device failed: Sparse table not supported. Verify that the WCS and WLC versions are compatible and try again.
I have double checked SNMP strings, IP Addressing and everything else I can think of. It just doesn't make sense that I can add a Controller with the same image but different hardware and no the other to the WCS server.
MGMcc solved my set up problem with my KDL-32ex713 which (i've swapped for a new model - its a long story). I used exactly the same ip addresses for the set up on this KDL-373x524 and got messages "wireless device found, local access failed, internet access failed". As my router and pc are the same as last time why the set up doesn't work this time and what I should do?
View 2 Replies View RelatedI have an Inspiron 1545 and I reinstalled Vista 32-bit, but I having problems with the comms driver (Conexant D400, External USB 56k Modem Rev : a05) and having the following message appear when I install the driver?
where to show MODEM?
I am trying to install Cisco Connect for my E1000 but I get the following error each attempt "An HNAP Call to the device failed for unknown reasons" I've already updated the router to 2.1 version of the Firmware.
Full Details
Error code: 82BD0305Error description: An HNAP call to the device failed for an unknown reason.Model name: unknownModel number: E1000Serial number: unknownFirmware version: unknownOperating system: Windows 7 SP 1Software version: 1.3.11069.2Connection type (WAN): unknownIP address (LAN): unknownIP address (WAN): unknownComputer IP address: 192.168.1.132
I inherited a Ciscoworks installation, and would like to create a credential set for a certain class of device. However, after searching around the interface and documentation, I cannot find instructions on how to add a credential set with certain snmp, ssh, credentials. We use ACS authentication and authorization?
View 1 Replies View RelatedWe migrated to LMS4.2 and i created new credential set and set it as the default. However, the new cdredential set applies only to newly added devices no to the migrated devices. for example when i run device credential verfication for a migrated device, the username used my LMS is "cwuser" as opposed to the one i created with the new credential sets. how can i make this new credentila set be applicable to all devices?
View 3 Replies View RelatedI have a problem with my AnyConnect clients connecting to an AD network via a 5510. Anyconnect VPN clients provide AD plus a one time passcode to authenticate to the 5510. This works fine apart from 3 things:
1. Once the VPN session has been established the user is further prompted for AD credentials when accessing an AD share for the first time. Once they provide the credentials the share can be accessed. Should the AD credentials not be passed through when the VPN connection is established? Or is this by design? What makes me think it's not be design is the fact that this could be related to problem 2.
2. Group Policy Update (windows gpupdate) fails. This again suggests to me that the full client/server relationship is not fully in tact.
3. In order to get Outlook to connect to exchange I've had to change Outlooks security settings from Negotiate (which would naturally choose Keberors), to NTLM. Not sure if this is related or not.
Note: DNS is functioning with out any problems
Maybe the first 2 issues are by design, but I thought the whole idea behind the AnyConnect VPN was that the remote machine would function as if connected to the LAN?
I'm having issue with 881W router. this router doesnt let me logon to it after I restart the router and enter correct credentials. after being at the router - it doesn't let me logon to its AP module even after adding correct credentials. I've changed 2 routers so far but see same issue.
try to setup up credentials using: username <username> privilege 15 secret 0 <password> or username <username> priviledge 15 password 0 <password>
My Dell Laptop is connected to Wildbue via LAN connection to Broadband. January or February I connected Belkin Router to obtain Wi-Fi access for other laptops, Cell and PS3, Everything seemed to be working fine. I tried to disconnect the Dell in order to use it via Wi-Fi. This caused problems when my sons laptop lost connection. My guess was that it was actually routed through the Dell via network. Anyway, as I was working to network all correctly. My sons friend decided that he couldn't wait for internet and forced another laptop to login to internet. In the process, it appeared that he changed by router password so that I could not access it. Being a beginner when it comes to network connections, etc., I spent alot of time trying to correct the Belkin Router. I finally disconnected the router and attempted to remove all detail on my Dell. I am sure that my adapter information is not completely accurate. Or so it appears. Note that I do have LAN internet connection and I can search for wireless access. If necessary, I will reinstall the Belkin Router since it is my understanding that it is needed for Wi-Fi access to my internet provider connected via Broadband modem.
I am sure that there will be corrections. I am sure that there is more that will need to be done in order to provide access to other laptops and cells. At this time, I am getting internet on my main laptop that is connected via LAN connection. However, I am having problems understanding adapters for wireless connects.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsPenis>IPCONFIG/ALL
Windows IP Configuration
[code]...
Recieved this unit from an individual who has very little knowledge (like myself) with the 800 series.
I'm having issues just getting into this device, when I power it on and console into the unit i am presented with an "Access Verification" prompt that requires credentials that I do not have/know.
At some point (not sure how) I managed to get to a "yourname#" prompt at which point I configured using this document here and created a username and password and some other basic settings, I saved the config and did a reload and it takes me right back to that "Access Verification" prompt.
Sould I be using the CCPE to gain access to this device instead? Is there a way to recover that "Access Verification" username and pass? How did I ever get to that "yourname#" prompt?
I have a 6509E switch with dual 6Kw power supply that is logging "Power supply 1 input has changed. Power capacity adjusted to 2671.20W" then will bounce back to normal at random times from 1sec to 10sec. Is there a command to check what each input level of the power supply to try to identify possibly which source is causing the problem? The power supply input lights remains green while this is occuring.
View 3 Replies View RelatedWe plan to use machine certificates on our notebooks with Windows Vista. Our authenticating server is Cisco ACS 5.1. To access the wireless network we want to use the machine certificate of the notebook and a verification of the corresponding computer account in the Active Directory. What authentication method is the best to check the machine certificate and if in the Active Directory exist the enabled corresponding computer account ? How to configure the ACS and the notebook to use it like described ?
View 1 Replies View RelatedI'm trying to test port-security in my c3550 but when I show port-security int f0/23 shows it only "Disabled" as below:
run
interface FastEthernet0/23switchport access vlan 200switchport mode dynamic desirableswitchport port-security mac-address stickyspanning-tree portfast
Network newbie need to verify all necessary services and protocols on a new WS-C6509-E are turned on. This layer 3 switch will be used to connect to servers.
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)
[Code]....
