Cisco Wireless :: 4402 - SNMP Operation To Device Failed
Mar 4, 2012
after upgrading the firmware on the wireless lan controller 5.2.178.0 on my cisco 4402 wlc's and rebooted the devices, I am getting matches on the audit status between whats on the contoller and the wcs software. so i am trying to apply whats in the wcs templates created for the controller and i am getting this error.
SNMP operation to Device failed: Attempt to set conflicting attribute value
I am thinking that i need to rebooted the wlc's again because from the error it sounds like the values that i am trying to write to the controllers are already present
View 1 Replies
ADVERTISEMENT
May 29, 2013
I am currently running WCS 7.0.230 I have controllers that are 2500 that are running 7.4.100.60?
My problem is that when I try to add my controller that is a Cisco 5500 running the same 7.4.100.60 I am getting the error SNMP operation to Device failed: Sparse table not supported. Verify that the WCS and WLC versions are compatible and try again.
I have double checked SNMP strings, IP Addressing and everything else I can think of. It just doesn't make sense that I can add a Controller with the same image but different hardware and no the other to the WCS server.
View 1 Replies
View Related
Nov 9, 2011
I am using LMS 4.0 and I keep encountering this issue "Error performing SNMP Operation"
View 5 Replies
View Related
Dec 13, 2011
I have a cat 3750 switch with the folowing snmp v3 config:
-snmp-server group admin v3 priv
-snmp-server user lmsadmin admin v3 auth md5 password1 priv aes 256 password2
The credentials on the device in LMS are as folowing:
where Auth. password = password1 and private password = password2:
When I run a credentials verification job, I get the following error message:
Error performing SNMP operation.
I have tried this on LMS version 4.0 and 4.1 with the same result.
View 2 Replies
View Related
Jun 1, 2010
i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
View 9 Replies
View Related
Jan 3, 2013
We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies
View Related
May 19, 2011
I have a guest network and lately I have been experiencing troubles with some users.The symptom, as I create a username and password and type'em in a laptop the authentication fields in the web authentication page don't keep the data as if I didn't type anything
WLC 4402-50
Version 7.0.98.210
View 7 Replies
View Related
May 10, 2012
I am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
View 9 Replies
View Related
May 16, 2011
MGMcc solved my set up problem with my KDL-32ex713 which (i've swapped for a new model - its a long story). I used exactly the same ip addresses for the set up on this KDL-373x524 and got messages "wireless device found, local access failed, internet access failed". As my router and pc are the same as last time why the set up doesn't work this time and what I should do?
View 2 Replies
View Related
Jul 10, 2012
I am trying to install Cisco Connect for my E1000 but I get the following error each attempt "An HNAP Call to the device failed for unknown reasons" I've already updated the router to 2.1 version of the Firmware.
Full Details
Error code: 82BD0305Error description: An HNAP call to the device failed for an unknown reason.Model name: unknownModel number: E1000Serial number: unknownFirmware version: unknownOperating system: Windows 7 SP 1Software version: 1.3.11069.2Connection type (WAN): unknownIP address (LAN): unknownIP address (WAN): unknownComputer IP address: 192.168.1.132
View 2 Replies
View Related
Jan 20, 2013
I have problems with setting the snmp retry / timeout parameters for our devices. I managed to import our devices with bulk import , but after it I realized that for some devices the snmp retry / timeout values were different ( created the bulk file with 3 retries and 30 sec timeout , but in the system the appear with 2 retries and 1 sec timeout). I tried to change it manually , but after a while it goes back to the wrong values.
View 1 Replies
View Related
Aug 16, 2011
i get for all devices telnet credential failed in my credential verification report. I exported the device from the Device Manager into a csv file to verify the correct passwords.The export shows the correct values in
<DEVATTRIB Name="primary_username">cwuser</DEVATTRIB>
<DEVATTRIB Name="primary_password">secretpassword</DEVATTRIB>
View 4 Replies
View Related
Nov 16, 2011
Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies
View Related
Mar 15, 2011
Does any know the meaning of this log message in a 7609 router - "SP: FAILED to write to DS1338 RTC device"?
So far as I can tell DS1338 RTC is supposed to be a (linux-related?) clock but I don't see how that's related to the.
View 7 Replies
View Related
Apr 24, 2013
I add 4510 and 4507 in zhe LMS ,but fault discovery failure.
View 7 Replies
View Related
Apr 15, 2010
I try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
View 11 Replies
View Related
Apr 7, 2011
I am trying image distribution to a c3560 device but I always get the error message SWIM1164. In the documentation it says to copy the logs and open a TAC Case but I would like to do some troubleshooting myself before opening a case.
Some actions to be taken prior to opening a case?
[code]...
View 8 Replies
View Related
May 9, 2012
This is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.
I increased SNMP timeout to 10 seconds to no avail.
View 5 Replies
View Related
Sep 14, 2012
I just reinstalled my Inspiron 1720 and everything works fine but the Bluetooth Peripheral Device which keeps reinstalling after every reboot.
In device manager Bluetooth Radios, "Dell Truemobile 355 Bluetooth + EDR" and "Microsoft Bluetooth Enumerator" are installed properly but I have in "Other devices" a Bluetooth Peripheral Device which does not want to install.
I used Driver CD provided when I purchased my laptop but it does not find any drivers to solve the problem. I also went to dell.com drivers to fin the latest one and this neither does not work .
View 2 Replies
View Related
Jan 26, 2012
We are using Catalyst 3750 switch stacks with software 12.2(44)SE. We have two stacks, only one with IP routing enabled.When we try to run an Acquisition Action on this, from Admin> Collection Settings> User Tracking, the system replies with an error "Failed to start acquisition: Device unreachable. Please enter a valid device"device Center reports "success" on all collector status.Acquisition starts successfully when we try with the other stack.With LMS 4.1 demo, users acquisition runs successfully.
View 18 Replies
View Related
May 30, 2013
I am using ISE 1.1.1.268 and WLC 7.2.111.3 and NAC agent version 4.9.1.6 on Windows 7 Client machines.
About once a day i get the error "ISE Alarm (WARNING): Dynamic Authorization Failed for Device".
The device it is referring to is my NAD, a WLC 5508 running 7.2.111.3
I have looked at the logs and I cannot see anything in the logs which corresponds to this message so that I can troubleshoot further. Maybe I can if I am enabling the correct logging level on the correct ISE component.
What are the components and the logging level that I should set to get some more detail about this error?
At the moment, I have only set debug logging on Active Directory. I have TRACE logging set on Posture, Run time AAA & prrt-JNI.
I do not want to enable too much debug logs, so what is the specific element that I should be debugging.
I thought debugging the posture element would be enough but when I look at the logs there is nothing there that relates to this message.
View 3 Replies
View Related
Jan 15, 2012
The installation of an ACE-4710 throughput upgrade license licence (ACE-AP-02-UP1) failed with an error message :CH01AC03/Admin# license install disk0:ACE20111213081741975.lic.Installing license... failed: No space left on device. [code]
View 4 Replies
View Related
Oct 20, 2012
I have an Inspiron 1545 and I reinstalled Vista 32-bit, but I having problems with the comms driver (Conexant D400, External USB 56k Modem Rev : a05) and having the following message appear when I install the driver?
where to show MODEM?
View 1 Replies
View Related
Apr 21, 2013
I want to set up AP 1552 as outdoor access point so serve clients. This AP is connected to 3750X switch and recieving power over ethernet.Now, by default AP 1552 come with bridge mode and it cannot be changed to local mode. I read on one of the post and made it ROOTAP but still the OPER STATUS is down. This device is already registered to my WLC.
what needs to be done to bring the AP in operational status.[code]
View 3 Replies
View Related
Feb 11, 2013
just installed 6 new APs to a client remote site off a 5508 controller. 5508 is running 7.0.116 total of 78 installed APs, mostly 1142's with a dozen or so1242s. All going perfectly until I was about to leave site and noticed two of the APs had no LEDs lit. Checked in the controller, as I had renamed them so knew they were on the system, and they are both there. Connected to each of them and was successful and everything seemed ok - no blue LED though. Rebooted them and the LEDs work as expected during the boot process but as soon as they have entered normal operation the LEDs go dark. urls....but no reports of it with anything other than 3502's.Change process is galacial and heavily monitored so dont want to invoke it if it wont address the concern.
View 10 Replies
View Related
May 25, 2011
I am trying to connect to my son's wireless internet with my own laptop. I can't get it to connect - I have tried to "renew IP address" and it doesn't work. I also got a message when I went to Start Run, etc etc "no operation can be performed on Wireless network while is has its media disconnected" I am able to connect to my own wireless internet at home on same laptop.
View 1 Replies
View Related
Mar 29, 2012
I'm using the Linksys WRT160N V3 for testing a few ambedded applications.I need to set the speed of operation of the router to 100Mbps. (or at least find out what speed it currently supports) I looked up the router home page and couldn't find anything concrete.
View 3 Replies
View Related
Jul 1, 2009
I've set up a USB drive to be shared via the router (tried both a fat32 and an NTFS drive). When I login from a windows machine I can use the share point without any problems. When I try to use it from a Mac (mounted via smb://192.168.1.1/sharepoint) I can access the folders and download files. I can even create folders. When I try to copy a file onto the share point (normal file name, small file size) I get an error saying "The operation cannot be completed because you do not have sufficient privileges for some of the items." The console log says: "7/3/09 1:01:06 AM kernel smbfs_composeacl: smbfs_setattr 13, ignored "
If I try to copy the file directly via a terminal window I see this:
Macintosh-3:tc user $ cp ~/test.plist ./
cp: ./test.plist: fchmod failed: Permission denied
As I see it there is a problem with leopard trying to set permissions when copying and the router refusing. How to get this to work?
View 8 Replies
View Related
Oct 27, 2011
I have an E1000 that is connected to my main computer via Ethernet and have found that it crashes almost every time I run a particular type of operation.I'm testing software and running PHP scripts that invoke cUrl to fetch data from a few different web services via SSL. I would say that at least every other time one of these operations begins, the router crashes -- I am unable to ping its internal IP and I have to power-cycle it to get back up and running.
I don't experience the crashes in any other context and I use the router all day long. I'm one release behind on firmware but the release notes on the most recent version don't suggest that upgrading would make any difference -- no mention of any bugs fixed, for example.
View 3 Replies
View Related
Oct 21, 2012
After a storm in my neighborhood my wireless router was reset. It is a wrt54g purchased in 2007. I had to reinstall the Easy Link Advisor from the net because the disk I had did not work with Windows 7. Everything went OK, however, I am not able to add a password. I keep getting the following error message: Error Updating Devise The Method or Operation is not Implemented. How do I get around this issue and install some sort of security for my home network?My wireless network was named genesis50 now it went back to linksys. How do I change the name back? The hard wired system still shows as genesis50.
View 2 Replies
View Related
Jan 19, 2012
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies
View Related
Jan 18, 2013
A PC from VLAN10 pings another PC in VLAN 20, and another PC between the switch “sales” and the central router is running a protocol analyzer. List all the protocols participating in this operation. You should determine the L2 source/destination addresses and L3 source/destination addresses.
View 10 Replies
View Related
Feb 21, 2013
System Information Firmware Version:V2.0.2.7CPU:STAR 9202 Router is operated 2y. No problems till now.There is sometimes abnormal lost of Internet connection, detected by LAN devices. I found it 3 days ago. This dysfunction is occasional 2-5 per day in occasional time.Nothing was changed/upgraded/updated in my WAN cable router or LAN or in the Cisco router. Nothing was changed on computers site (OS,LAN cards, drivers, ...). Just the problem is discovered on the router side.LAN operatation is correct, no problems was founded. Just the devices on LAN lose the internet connection (Win7, Lnx, Mac).
This is status of my WAN - does not matter if the internet connection was lost or not. It is still same:
STATUS-WAN/Gateway
Interface: UP
IP Address is assigned (checked by provider - correct)
Default Gateway and DNSs are assigned too(checked by provider- correct)
What was checked by me:
1. A. I disconnected the cable router from Cable modem
B. I connected the Cable router directly to laptop. Internet connection was right.
2. I called to my Cable provider to check my connection:
- with direct laptop connection to Cable router - Right
- with Cisco router connected to Cable router - Right, but no Internet connection on LAN side behind the Cisco router
3. Standard procedure was tested:
- Unplugged (electricity & cabling) all devices - Cable modem, Cisco router as well.
- Restart of Cable modem, +30 sec. connection of IP cable to Cisco router, start of Cisco router Still same. No Internet connection.
- SETUP/SUMMARY/Network Settings Status - DHCP Release or DHCP Renew was tryed - Still same.After several minutes - was Internet connection Renewed. Just by itself. how?
View 1 Replies
View Related