Cisco :: LMS 4.0 / Error Performing SNMP Operation
Nov 9, 2011I am using LMS 4.0 and I keep encountering this issue "Error performing SNMP Operation"
View 5 Replies
ADVERTISEMENT
Cisco :: 3750 Error Performing SNMP Operation
Dec 13, 2011I have a cat 3750 switch with the folowing snmp v3 config:
-snmp-server group admin v3 priv
-snmp-server user lmsadmin admin v3 auth md5 password1 priv aes 256 password2
The credentials on the device in LMS are as folowing:
where Auth. password = password1 and private password = password2:
When I run a credentials verification job, I get the following error message:
Error performing SNMP operation.
I have tried this on LMS version 4.0 and 4.1 with the same result.
Cisco :: LMS3.2 Snmpv3 Error Performing SNMP Operation
Jun 1, 2010i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
View 9 Replies View RelatedTCP Error - Communication Error Occurred Operation Timed Out
May 1, 2012I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies View RelatedCisco Wireless :: 4402 - SNMP Operation To Device Failed
Mar 4, 2012after upgrading the firmware on the wireless lan controller 5.2.178.0 on my cisco 4402 wlc's and rebooted the devices, I am getting matches on the audit status between whats on the contoller and the wcs software. so i am trying to apply whats in the wcs templates created for the controller and i am getting this error.
SNMP operation to Device failed: Attempt to set conflicting attribute value
I am thinking that i need to rebooted the wlc's again because from the error it sounds like the values that i am trying to write to the controllers are already present
Cisco :: 5500 - SNMP Operation To Device Failed / Sparse Table Not Supported
May 29, 2013I am currently running WCS 7.0.230 I have controllers that are 2500 that are running 7.4.100.60?
My problem is that when I try to add my controller that is a Cisco 5500 running the same 7.4.100.60 I am getting the error SNMP operation to Device failed: Sparse table not supported. Verify that the WCS and WLC versions are compatible and try again.
I have double checked SNMP strings, IP Addressing and everything else I can think of. It just doesn't make sense that I can add a Controller with the same image but different hardware and no the other to the WCS server.
Linksys Wireless Router :: WRT610N - Error Saying Operation Can Not Be Completed
Jul 1, 2009I've set up a USB drive to be shared via the router (tried both a fat32 and an NTFS drive). When I login from a windows machine I can use the share point without any problems. When I try to use it from a Mac (mounted via smb://192.168.1.1/sharepoint) I can access the folders and download files. I can even create folders. When I try to copy a file onto the share point (normal file name, small file size) I get an error saying "The operation cannot be completed because you do not have sufficient privileges for some of the items." The console log says: "7/3/09 1:01:06 AM kernel smbfs_composeacl: smbfs_setattr 13, ignored "
If I try to copy the file directly via a terminal window I see this:
Macintosh-3:tc user $ cp ~/test.plist ./
cp: ./test.plist: fchmod failed: Permission denied
As I see it there is a problem with leopard trying to set permissions when copying and the router refusing. How to get this to work?
Windows 7 - Error Code 0x000005b4 / Operation Returned Because Timeout Period Expired
Nov 1, 2012I got this error this operation returned because the timeout period expired error code 0x000005b4
View 1 Replies View RelatedCisco :: Error %Bad OID When Configuring SNMP On 1941
Jan 28, 2013I get the following error:
Router#config t
Router(config)#snmp-server view rttmon ciscoRttMonMIB included
%Bad OID
The same command is accepted on a Cisco 2900 router
Router#show version
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
[Code]......
Cisco Switching/Routing :: 3750 SNMP Second Stack Is Showing Error
Mar 5, 2013We have a stack setup with 2 C3750x-12s and 5 C3750x-48p switches. We have two of these stacks. One is working and responding with snmp just fine. Our second one is showing the errors in the logThe only difference i see between the two stacks right now are the sw versions.
View 1 Replies View RelatedCisco WAN :: 2900 Network Performing Slow
Feb 7, 2012I have this small network comprising of around 40 users complaining about the poor speed. And they have 2900 WAN router having 10M service. The interesting thing is that they are using proxy server for all the communication.I am very new to the server side of thing-and wanted to confirm if the proxy server is packed full to its capacity for serving to clients' requests making it slow or its something to do on the network like WAN link being overloaded or showing errors.I did "sh interface g0/1" (WAN interface) and to me it looks there is not much load as the tx and rxload values are fairly ok. (as shown below). Moreover the output drops is 7341. I am still guessing if thats not too bad??
The other thing I did was to test the "sh ip nat transalations" which is all coming from the PRoxy server and was wondering if that is the place of bottleneck. Currently there were showing around 570 entries. Below are the output from there as well. Also, I was keen to know what is the "----" indicates in some of th output? [code]
Backup To External Drive Not Performing?
Mar 11, 2011I am not sure whether this is the right category to which I should submit my question, but I couldn't find a section for "other software support" or anything like that.I am running Windows SBS 2003 at one of my clients and we are using Syncback as the backup software to backup important files and folders that gets written to the server on a daily basis.Now we are using two external drives for this purpose, alternating the two every second day, for improved security.However...I have set up the backup profiles exaclty with the same configurations and everything...everything is identical. But the backup to one of my drives does not want to perform giving the error : "the folder on the destination drive does not exist and can't be created"The folder does exist though, and what puzzles me is that running the backup manually or even copying files manually from the same server backup folders to the drive works perfectly, but when running the scheduled backup, it fails...and yes, the logon and authentication is set to "run as administrator" and the username and password is entered correctly.Like I said, the configs of the two drives are exactly the same, and the backup to the other drive works perfectly.I am using the Syncback free version, and support for the free version on the 2Brightsparks website is unavailable
View 2 Replies View RelatedCisco WAN :: 3750 Performing QOS Against Number Of SVI VLans On Per Customer Basis
Apr 29, 2012I have a Cisco 3750 switch stack and am performing QOS against a number of SVI vlans on per customer basis. I have 8 customers, each with a /29 public subnet and each with an SVI as a gateway within that /29 range. I then have a "routable" SVI vlan for routing upstream to the internet. [code]
The service policy attached to the interfaces above is supposed to perform policing on download and upload traffic. The service policy is attached to the Routable VLAN for download policing and the Customer VLAN for upload policing. For example, traffic entering the routable VLAN will be policed based on traffic matching an access list to the customers IP range (download). Traffic entering the customer VLAN will be policed based on traffic matching an access list from the customers IP range (upload).The command I am using to police is as follows - police 10485500 966080 exceed-action drop.The problem I am experiencing is traffic into the routable VLAN is being successfully policed down to the 10Mbps i have specified on a per customer basis (download).Traffic entering the customer VLAN is NOT being policed at all (upload).I am limited as to the use of the parent policy map I have specified on the interface, as I can only assign it in one direction (input).
SW For Performing Scheduled Speed Tests On Internet Connection?
Jul 12, 2011We're since long having a problem with a DSL internet connection. The connection goes down periodically, for short times, and when performing speed tests, the connection speed varies and is usually lower (0.7 Mbit/s) than what the ISP promises (1.5-2 Mbit/s). Moreover, what modem is being used seems to have an effect.Now, I want to trouble-shoot this and get some hard facts on the behaviour of the connection. I would like to do repeated speed tests over say 24 h or so. They should be done every 3 min or so (to catch short glitches).
My question is: what software tool can I use for this? I have been searching the internet for hours, downloading a handful of applications, without finding anything that I could use. There are loads of applications that log and graph the current upload and download speeds, but that's something else - I need a tool that downloads/uploads files from/to a server, in intervals specified by me (3 min), logging the result and presenting it graphically.
Netgear WNDR3700 - Well Performing Card To Make Up No Hardwired Connection
Jul 2, 2011I'm going to be moving into a place in the next couple months where I'll have to go wireless on my desktop (until now I've just done Ethernet so I don't even have a wifi card on my desktop). The router/modem aren't anywhere near my bedroom so my gear will be going wireless from now on All my devices are built-in wifi ready but not my desktop.
I would like recommendations as to a rock-solid, reliable, fast and well performing card as I can to make up for no hardwired connection. Especially with BF3 coming out I'm not all that thrilled with being forced into this situation but you gotta do what you gotta do. Anyhow, I'll be bringing my router (Netgear WNDR3700) so I'll have the range and speed from there about as good as I can get, so I'd like a card of equal merit.
One side note...probably not really feasible considering I want speed and performance as a priority, but I would love a card (if possible) without bullshit antennas sticking out of the case, or with external antennas you have to set up on your desk. I will go that route if I have to but man that is an aesthetic nightmare, IMO. The ones that stick out of the back of the case are the worst looking for me just as a caveat.
Cisco :: List All The Protocols Participating In This Operation?
Jan 18, 2013A PC from VLAN10 pings another PC in VLAN 20, and another PC between the switch “sales” and the central router is running a protocol analyzer. List all the protocols participating in this operation. You should determine the L2 source/destination addresses and L3 source/destination addresses.
View 10 Replies View RelatedCisco Routers :: RVS 4000 - WAN Abnormal Operation?
Feb 21, 2013System Information Firmware Version:V2.0.2.7CPU:STAR 9202 Router is operated 2y. No problems till now.There is sometimes abnormal lost of Internet connection, detected by LAN devices. I found it 3 days ago. This dysfunction is occasional 2-5 per day in occasional time.Nothing was changed/upgraded/updated in my WAN cable router or LAN or in the Cisco router. Nothing was changed on computers site (OS,LAN cards, drivers, ...). Just the problem is discovered on the router side.LAN operatation is correct, no problems was founded. Just the devices on LAN lose the internet connection (Win7, Lnx, Mac).
This is status of my WAN - does not matter if the internet connection was lost or not. It is still same:
STATUS-WAN/Gateway
Interface: UP
IP Address is assigned (checked by provider - correct)
Default Gateway and DNSs are assigned too(checked by provider- correct)
What was checked by me:
1. A. I disconnected the cable router from Cable modem
B. I connected the Cable router directly to laptop. Internet connection was right.
2. I called to my Cable provider to check my connection:
- with direct laptop connection to Cable router - Right
- with Cisco router connected to Cable router - Right, but no Internet connection on LAN side behind the Cisco router
3. Standard procedure was tested:
- Unplugged (electricity & cabling) all devices - Cable modem, Cisco router as well.
- Restart of Cable modem, +30 sec. connection of IP cable to Cisco router, start of Cisco router Still same. No Internet connection.
- SETUP/SUMMARY/Network Settings Status - DHCP Release or DHCP Renew was tryed - Still same.After several minutes - was Internet connection Renewed. Just by itself. how?
Cisco :: Unified Operation Manager 2.3 With CUCM 8.5?
Sep 15, 2011I have a CUOM 2.3 and CUCM 7.0 installed, we are planned to have a major upgrade to CUCM to 8.5 soon, do i need to upgrade my CUOM ,since CUOM is a Network management system? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license? Is OM 2.3 to 8.X is a direct upgrade?
View 3 Replies View RelatedCisco :: Unified Operation Manager 2.3 With CUCM 8.6?
May 16, 2012My Customer today have CUOM 2.3 and CUCM 7.1.3. He is planning to do upgrade CUOM 8.6 and CUCM 8.6. My question is: Is it possible to do upgrade CUOM directly to 8.6? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license?
View 4 Replies View RelatedCisco LAN :: 3502i AP Operation Status In Downloading?
Jun 24, 2012I have an issue with two APs (3502i) which is associated to controller wism2. Total number of APs are connected to this controller is 422 and once I added two new APs (3502i) to this controller I am unable to see these APs coming up. Getting error messages like wrong primary controller nad secondary controller. When I loggedin to the controller through CLI following are the details I am getting for the APs which is not registering to the controller:, Also for comparison I am attaching the statistics for the AP which is working good and is able to register.
Note: I thought the problem with these two APs and will try replacing them but when i connected the other two APs to different switch and different subnet the same errors we are seeing.
ISSUE with the AP:show ap config general AB2-4N-AP11
Cisco AP Identifier.............................. 440
Cisco AP Name.................................... AB2-4N-AP11
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. -
AP Regulatory Domain............................. Unconfigured
[code]....
Wifi Repeater Setup And Operation?
Aug 16, 2012I have a wireless access point/modem at one end of my property (which I cannot relocate). To improve wireless connectivity on the other end of the property I am thinking of placing a wifi repeater (probably a cheap one like http:[URL]... mid-point in the property. However I don't quite understand how these things work. I assume repeaters, extenders, boosters are all the same thing?
Does the repeater actually create a new seperate wifi network, so I will effectively have two wifi networks/SSIDs? or will my wireless devices still see only one wifi network? If it creates two wifi networks what happens when I move through the property with say a laptop, will the laptop need to disconnect from one and reconnect to the other hence interrupting the connection? (which is not ideal).
Also does the repeater take up an IP from my main wireless access point/modem? My setup uses a block of static IPs and hence I would prefer not to waste an IP on the repeater if possible.Homeplugs is something else I'm looking into but that seems to be a more expensive option. With Homeplugs I would disable the wireless on the main access point/modem. Then use the Homeplug to put a wireless access point in the centre of my property hence giving fuller coverage.I've also tried higher DBi antennas (& directional ones) but they have not been effective.
Cisco Wireless :: AP 1552 Operation Status Is Down On WLC 5508
Apr 21, 2013I want to set up AP 1552 as outdoor access point so serve clients. This AP is connected to 3750X switch and recieving power over ethernet.Now, by default AP 1552 come with bridge mode and it cannot be changed to local mode. I read on one of the post and made it ROOTAP but still the OPER STATUS is down. This device is already registered to my WLC.
what needs to be done to bring the AP in operational status.[code]
Cisco Routers :: RV180 Router Mode Operation
May 9, 2013 wether the Cisco RV180 router model can be configured with a public IP address on the LAN interface? I'm planning to use it in the following setup:
Internet ------------- WAN port (public IP) RV180 LAN port(public IP)-------------- WAN(public IP) RV016 LAN (private IP)
Disabling gateway operational mode and switching to router should disable NAT and allow this setup but need to confirm if it works? I'm concerned if the web management interface actually allows a public IP to be set on the LAN side.
Cisco Wireless :: 1142 APs LEDs Not Working In Normal Operation
Feb 11, 2013just installed 6 new APs to a client remote site off a 5508 controller. 5508 is running 7.0.116 total of 78 installed APs, mostly 1142's with a dozen or so1242s. All going perfectly until I was about to leave site and noticed two of the APs had no LEDs lit. Checked in the controller, as I had renamed them so knew they were on the system, and they are both there. Connected to each of them and was successful and everything seemed ok - no blue LED though. Rebooted them and the LEDs work as expected during the boot process but as soon as they have entered normal operation the LEDs go dark. urls....but no reports of it with anything other than 3502's.Change process is galacial and heavily monitored so dont want to invoke it if it wont address the concern.
View 10 Replies View RelatedCisco Switching/Routing :: 3750 Ever Changing IP SLA / RTR Tracking Operation
Nov 7, 2011I just tested IP SLA with tracking on a 3750 12.2(46)SE. And the configuration was simple enough and tested fine for redundant static routing: [code] Then I tried to do the same on a 3560 switch running 12.2(55)SE3. ip sla went in fine. But when I went to put in the track I was presented with "list boolean and" (for example) after the track and the identifier.I tossed in the ip sla "10" as the object. But shopw track shows the boolean AND as down. I don't get why the track feature is different in two switches so close in IOS version. How do I get the 3560 to track the ip sla as my 3750 does?
View 3 Replies View RelatedCisco Switching/Routing :: Sup7L-E - How To Select 1-Gigabit Operation
Aug 23, 2012Documentation discusses "1-Gigabit Operation", where all 4 1-Gig SFP's on Sup7L-E are enabled. But it does not say __how__ to select either 10-G or 1-G operational modes.
View 3 Replies View RelatedCisco Infrastructure :: Installation Of Nexus 1000v 4.2.1.SV2.1.1 - Operation Timed Out
Nov 6, 2012We are trying to install the latest version of Nexus 1000v to ESXi5.1 and the installer application is much better than the previos one, but we are having problems with implemetation, because deploying of OVA file times out.
First attempt: Nexus-1 was successfully deployed on ESXi-1, but Nexus-2 which should be deployed on ESXi-2 returned an error: "Deploy OVF template":"Operation timed out." Second attempt: Deploying of Nexus-1 returned the same error Third attempt: The same as the first attempt.
It looks like that there is a time limit which is used for deploying OVA file and since file needs to be uploaded to ESXi it takes too long, so the installation fails. Is it possible to extend this time?
Operation Returned Because Timeout Period Expired Windows 7
Apr 18, 2011I have a new Win 7 Dell Precision Workstation that will not log in to my domain. I get an error that there is no login server available if I attempt to log in using a domain account. I log in as the local admin and then try to join a domain using the Join a Domain or Workgroup wizard. I then get an error stating "this operation returned because the timeout period expired". I have had to reset my core switch to get a couple of the new boxes (including this one) to even join the domain. I also show no internet in the Network and Sharing Center most of the time.
View 2 Replies View RelatedNo Operation Can Be Performed On Wireless Network While Media Disconnected
May 25, 2011I am trying to connect to my son's wireless internet with my own laptop. I can't get it to connect - I have tried to "renew IP address" and it doesn't work. I also got a message when I went to Start Run, etc etc "no operation can be performed on Wireless network while is has its media disconnected" I am able to connect to my own wireless internet at home on same laptop.
View 1 Replies View RelatedCisco WAN :: Configuring HWIC-2SHDSL Card In A 2911 For CO Mode Operation?
Dec 12, 2011I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
Linksys Wireless Router :: Changing Operation Speed Of WRT160N V3
Mar 29, 2012I'm using the Linksys WRT160N V3 for testing a few ambedded applications.I need to set the speed of operation of the router to 100Mbps. (or at least find out what speed it currently supports) I looked up the router home page and couldn't find anything concrete.
View 3 Replies View RelatedCisco Switching/Routing :: 4500 Redundancy Status Still Shows As RPR In Operation Mode
Feb 27, 2012On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
After it came back up again, the redundancy status still shows as RPR in operation mode.
Linksys Wireless Router :: E1000 Crashes Fairly Predictably After Particular Type Of Operation
Oct 27, 2011I have an E1000 that is connected to my main computer via Ethernet and have found that it crashes almost every time I run a particular type of operation.I'm testing software and running PHP scripts that invoke cUrl to fetch data from a few different web services via SSL. I would say that at least every other time one of these operations begins, the router crashes -- I am unable to ping its internal IP and I have to power-cycle it to get back up and running.
I don't experience the crashes in any other context and I use the router all day long. I'm one release behind on firmware but the release notes on the most recent version don't suggest that upgrading would make any difference -- no mention of any bugs fixed, for example.