Documentation discusses "1-Gigabit Operation", where all 4 1-Gig SFP's on Sup7L-E are enabled. But it does not say __how__ to select either 10-G or 1-G operational modes.
View 3 RepliesAny information on supervisor WS-X45-SUP7L-E? I saw that it has 520Gbps of backplane, but does it supports Netflow? How many uplink does it has?
View 6 Replies View RelatedWhat is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies View RelatedAre there any plans to support a "shared backplane mode" like on SUP6-E that enables the use of four 10G oversubscripted uplink ports in redundant mode? now there is support for up to two active 10G links in redundant mode.
View 2 Replies View RelatedI upgraded IOS-XE on 4500E (SUP7L-E) to cat4500e-universalk9.SPA.03.03.00.SG.151-1. I encounter the log when i try to issue write mem commad
% VRF table-id 0 not activeCompressed configuration from 8947 bytes to 2140 bytes[OK].
I will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies View RelatedWhat is the case with redundant Sup engine 10GbE interfaces. We can only get one in active state, the other interface stays inactive? Can we have all four interfaces active sharing the backplane?
Mod Ports Card Type Model
---+-----+--------------------------------------+------------------+-----------
3 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
4 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active
4 Standby Supervisor SSO Standby hot
We are planning for the first installation of 4500 switches containing these supervisor modules. I'm trying to determine the interface numbering convention for ports on the supervisors. Our existing 4500E all have SUP6 modules with twin-gig converters - so I am familiar with the numbering conventions used on those supervisors. How does this change with the software based selection command "hw-module uplink select" used in SUP7?
View 2 Replies View Relatedknow if it is supported connecting the SUP7L-E 10GE ports to a C3KX-NM-10G, using a SFP-H10GB-CU5M (or shorter).
View 3 Replies View Relatedi need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies View RelatedI just tested IP SLA with tracking on a 3750 12.2(46)SE. And the configuration was simple enough and tested fine for redundant static routing: [code] Then I tried to do the same on a 3560 switch running 12.2(55)SE3. ip sla went in fine. But when I went to put in the track I was presented with "list boolean and" (for example) after the track and the identifier.I tossed in the ip sla "10" as the object. But shopw track shows the boolean AND as down. I don't get why the track feature is different in two switches so close in IOS version. How do I get the 3560 to track the ip sla as my 3750 does?
View 3 Replies View Relatedhow we can select a network module for 2811 router?gigabit or ethernet Hwic?
View 1 Replies View RelatedOn a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
After it came back up again, the redundancy status still shows as RPR in operation mode.
I am calculating Cisco 4500X power consumption requirements to select appropriate UPS systems. I have 4500X switch with dual power supplies.which value should I take for power consumption calculation, in data sheet it has two values: AC Power Max Rating: 750W System Power Consumption: 330W nominal/400W max
Which values should I take, to calculate UPS systems capacity? And also I am interesting when 4500x has two power supplies what is power consumption?
We have a number of 3845 routers, some running IOS 12.4(22)T2 and earlier and some running 12.4(24)T4. On the ones with 12.4(22)T2 and earlier, gigabit interface g0/1 shows interface down/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. On the ones with 12.4(24)T4, gigabit interface g0/1 shows interface up/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. Interestingly in both cases, the "show controller g0/1" command shows " network link is down (NO CARRIER)" when there is no cable attached. It makes sense to us that the interface status would be down/down when there is no cable attached. It does not makes sense to us that the interace would be up/down. Did Cisco at some point change their philosophy on whether an interface should show down/down or up/down when there is no cable attached, or is this a bug?
View 1 Replies View RelatedI am trying to test the gigabit ports on a Cisco 2950 switch. 1000Base-SX. I have the internet or dhcp server connected to port 24 on the first switch and my pc hooked up to the (any) port on the second switch. Both switchs are connected with a fiberoptic cable with MTRJ connectors on either side.
Now when I use gi0/2 on both switchs all works fine. I get a dhcp address from the router on the other end of the first switch. but when ever I include gi0/1 on either end of the fiber optic cable neither of the ports will initialize (neither of the leds above the ports light up). I have deleted all the config files before booting up the switchs so they should have a default blank configuration.
When looking at the Http web page for the switch I dont see any issues with the port. what can I do to make sure these ports are working or can be configured?
I will not be able to post back any more information about the switch until next tuesday. Im off till then.
im currenly configuring a 4500X with 16 port. All sfp are 1Gig, but when I input show ip int brief, it shows that the interfaces are on 10 Gig. Does Catalyst 4500X already support the 1Gig SFP without inputting a command or do I have to configure it to activate the 1Gig interface?
View 6 Replies View RelatedAre all ports on Catalyst 4500X Gigabit/10-Gigabit or just the ports on 8-port module. We are looking at 4500X for campus distribution layer but need Gig ports to access switches for now and may year from now will be using 10G.
View 7 Replies View RelatedI have a 3550 switch right now, and need to upgrade to a gigabit switch, so I'm looking at a 3560G-48. For some reason I purchased an EMI version of my 3550, but run the ipbase image...what I need to look for - is a 3560G-48-s good for what I need?
View 4 Replies View RelatedBrand new 2960. When I plug a cable into the port, nothing happens. The port light doesn't begin negotiation or anything, it just stays dark. The cable works fine--I have it on another switchport with a crossover connector connecting to a little Cisco SOHO switch without problems.
I've done the following:
switchport
switchport mode trunk
switchport trunk allowed vlan 1
no shutdown
In other words, I've fiddled with it. But I don't know why it doesn't light up..
I have two switches, WS-3750-24PS-S connected in two cabs via fiber. Patch panels at both ends with patch leads. Used tester to confirm end to end fiber connectivity. When plugged in, one switch lights up the other does nothing.
Ports are as follows:
interface GigabitEthernet1/0/2
switchport trunk encapsulation dot1q
switchport mode trunk
same at both ends. Tried both GI ports same result. swapped transceivers over and the same result, (one switch lit one not - the same switch in both cases). put both transceiver in each switch, (gi0/1-0/2 in a single switch). on the one that lights up in the original scenario we get link on both ports and they come up, on the other nothing happens. shut down both ports on the malfunctioning switch and no shut them, no change.
Show transceivers doesn't show transceivers on the malfunctioning switch, and no attempt is made to bring the ports up if the fiber is removed and replaced.
it is almost as though the two gb ports are kaput. Anything else I can try?
I realize this is just a small business switch, basically a rebranded Linksys, but why I'm only getting 200Mbits/s
- 48 port - 10/100/1000 , set to standalone mode
- 3 separate PCs on this switch , all are fast machines with Core 2 duo / plenty of RAM etc...
- all 3 auto-sense 1Gbps connection
I use iperf tool for bandwidth testing and no matter which PC I pick as server, which as client I get about 150 to 250Mbits/s
I am not looking for full 1000 here, but 200 seems rather sad....
- jumbo frames seem to make no difference
- I am using TCP test in iperf , standard no extra flags , 10 seconds, 20 seconds or even 30 seconds all come out the same.
- wiring is shady as some of it is just Cat5 , but when going from one laptop on the switch to another with brand new Cat6 cables I STILL only got 200.
I have the possibility of upgrading a DS3 to Metro Ethernet, Gigabit connection. My dilemma is I have two VTP domains in my network. How can I get two VTP domains over one trunk to a remote site ?
View 0 Replies View RelatedI have a Cisco 2851 router and need an additional gigabit Ethernet port. How to get the part number I need to order?
View 3 Replies View RelatedIs it possible to reset this switch oif yo uare unable to get into the console or web interfaces?
View 2 Replies View RelatedI can assign IP addresses to any of the 24 FastEthernet ports (it is a 24 port switch!). However, I have fitted the WS-G5482 Gigabit adaptor to give me Gig ethernet capability. It does not seem to be possible to assign an IP address to the adaptor.I realise that as it is an 'add on module' (well, a plug in module) this is different to the 24 port in the 'body' of the switch. I also have read that these Gig adaptors will only connect to other Gig adaptors (I found that out by trial and error, and then confirmed it by searching here).it's not possible to assign an IP addy to one of the plug in modules; it is not a big deal but I am planning to assign some IP addresses for remote management etc. I was going to use the Gig port for this but it may not be possible.
AH PS I am using the switch and connecting to the internet via the Gig adaptor, then out from one of the fastethernet ports to another little switch and then on to a router and out to the internet, so the switch and the plug in module are working fine.
I have a question about speed negotiation process between interfaces. I have 3650X Sw and 2960S-48port. All ports of two are GigabitEthernet, however the link between them is only 100Mb/s, Full duplex. I try to set the speed 1000 Mb/s manually in the interface then the interface never up. Its status is down/down. I must set back to speed auto. I show interface Gigabit0/24 in Sw 3650-X and figure out that there are many output drop (over 600000). I clear counter then after two days the output drop is over 70000. This link is trunk link between two switches, all ports of access SW are Gigabit and connect to PC. First, I thinks the 3650X is throttled somewhere in output direction of trunk link. But there is another trunk link (Gi0/23) to another 2960S-48port and no output drop number in this interface. This Giga 0/23 speed is 1000 Mb/s (auto speed, auto duplex)
Does any outside things impact the speed negotiation process between 2 interfaces? And output drop number may caused by abnormal speed between two Gigabit interface?
Trying to configure the Cisco 4948e switch gigabit ethernet port with "switch port trunk encapsulation dot1q", but didn't get the option. Please find below the options got after "swith port trunk"............
SW(config-if)#switch port trunk ?
allowed Set allowed V LAN characteristics when interface is in trunking mode
native Set trunking native characteristics when interface is in trunking mode
pruning Set pruning V LAN characteristics when interface is in trunking mode
SW(config-if)#switch port trunk. Please find below the version of the SW............
SW#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-LANBASE-M), Versi
on 12.2(54)SG1, RELEASE SOFTWARE (fc1)
Technical Support: {URL}
ROM: 12.2(44r)SG11
Hobgoblin Revision 21, Fortooine Revision 1.22
[code]...
So, whether the command is not supporting on this Cisco switch ? But we have Cisco 4948 Cisco sw where that command is working fine.
We have recently purchased a Cisco 4506 that has several Gigabit Ethernet modules installed.One of the Ethernet Gigabit modules - a WS-X4424-GB-RJ45 - is being picky with who it talks to at Gigabit Ethernet.
If I plug a laptop into one of it's RJ45 ports using a Cat 6 cable, nothing happens. No link light, no notification of link up or down on port statistics, absolutely nothing.If I plug a server into the same port it works fine at Gigabit Ethernet (even using the same Cat 6 cable).I can get the module to recognize a laptop if I fix the speed/duplex on the laptop to 100Mb/Full. I have tried this with other staff laptops from different vendors (HP / Dell / etc.) all with the same result.
The module directly underneath this module - a WS-X4448-GB-RJ45 - works fine for both laptops and servers. We have tried swapping the module positions but to no avail.
According to the following Cisco webpage, cross-stack 10-Gigabit EtherChannel is possible on the 3750 with up to two 10-Gigabit modules, using LACP: url...However, the webpage doesn't confirm if this functionality is restricted to a particular 3750 model, such as 3750E, or if it applies to all models. It also doesn't specify any particular IOS feature set. I've tried Cisco Software Advisor but it doesn't list this feature on either the 3750E or 3750-X. This is possible on the 2960-S switches (i.e. cross-stack 10gig EtherChannel)?
View 23 Replies View RelatedWe have Cisco 3524XL switch, Motorola AXS1800 chassis. I am configuring this cisco switch so I can connect AXS1800 traffic thru cisco 3524XL, on switch port gigabit 0/1, I am using cisco Part no. WS-G5486 (1000Base-LX) connector to connect to AXS1800, both port are member of vlan 200 allowed, and configured dhcp-server 192.168.0.1, but still I can't ping any host or host can't get DHCP server.
View 2 Replies View RelatedWe recently upgraded the switch to which an old security device was connected. It worked fine on the old switch's FastEthernet port, which was configured for speed 10 and duplex half, as that is what the device required. The new switch is a 3560X with all Gigabit ports, but the security device's port, also configured with speed 10 and duplex half, does not connect properly.As a temporary test, we daisychained another switch that has FastEthernet ports, and the security device works again.Is there anything else that needs to be added to the configuration, when using Gigabit ports at 10/half?
View 4 Replies View RelatedI need to connect one sw3750E with two 3750X , with Uplinks at 10 GBps. My doubt is the next:
Switch 3750E has two TwinGig Adapter Converting 10 Gigabit Ethernet X2, phisically each twinGig adapter has 2 slots for SFP modules. Can I install sfp+ If I want to use copper for Uplink at 10 Gbps, I just need to install one SFP-H10GB-CU5M transceiver ???? the other SFP slot is disabled automatically?
in the other side 3750X in order to support copper at 10 Gbps a C3KX-NM-10G network module is considered, this will be connected to SW3750E by means of SFP-H10GB-CU5M.
The second 3750X will be connected to second twinGig Adapter of 3750E using another SFP-H10GB-CU5M transceiver.