Are there any plans to support a "shared backplane mode" like on SUP6-E that enables the use of four 10G oversubscripted uplink ports in redundant mode? now there is support for up to two active 10G links in redundant mode.
View 2 RepliesI received the following info from Cisco's TAC and wanted to inquire further before I start reconfiguring the switch:
In a redundant Sup-6E setup, the following configuration is supported :
- 1 TenGig uplink on Active Sup and 1 TenGig uplink on Standby Sup
- 1 TenGig uplink on Active Sup and 2 Gig uplinks on Standby Sup
- 2 Gig uplinks on Active Sup and 1 TenGig uplink on Standby Sup
- 2 Gig uplink on Active Sup and 2 Gig uplinks on Standby Sup
If you invoke shared backplane mode, the following configuration can also be supported:
- 2 TenGig uplinks(blocking) on Active Sup and 2 TenGig uplinks on Standby Sup
- 2 TenGig uplink(blocking) on Active Sup and 4 Gig uplinks on Standby Sup
- 4 Gig uplinks on Active Sup and 2 TenGig uplinks(blocking) on Standby Sup
- 4 Gig uplink on Active Sup and 4 Gig uplinks on Standby Sup
Here's the command and information about the "shared-backplane" mode :- [URL]
Currently, we have 2 SUP 6-Es(Module 5 - Active and Module 6 - Stand-by) setup in a redundent mode. I am planning on changing the redundent mode to the shared backplane mode so I can use 2 TenGig converters to uplink 2 access-switches. We purchased 2 TenGig converters and here is how I am planning on using them:
1- One will be used to uplink to two 3750 switches(stacked)
2- One will be used to uplink to a 2960 using a Gig SFP
My questions are:
1- Do I have to install the 2 TenGig converters(4-Gig Uplinks) in the same Module? Or can I use one one in module 5 and the second one in module 6?
2- Will changing the redundant mode to the shared backplane mode require rebooting the switch or disrupt the funtionality of the other linecards?
What is the case with redundant Sup engine 10GbE interfaces. We can only get one in active state, the other interface stays inactive? Can we have all four interfaces active sharing the backplane?
Mod Ports Card Type Model
---+-----+--------------------------------------+------------------+-----------
3 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
4 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active
4 Standby Supervisor SSO Standby hot
I have a new building to add to our campus and I have been encouraged to run single mode fiber. All of my other buildings are connected with multi-mode fiber. I just want to make sure i will not have an issue if I run single mode to the new building with SM SFP's.
View 2 Replies View RelatedAny information on supervisor WS-X45-SUP7L-E? I saw that it has 520Gbps of backplane, but does it supports Netflow? How many uplink does it has?
View 6 Replies View RelatedI'm looking for switches that support single mode fiber connections and would like to know if "WS-C3750-FS-S Catalyst 3750 24 100BaseFX + 2 SFP" and "WS-C3750G-12S-S Catalyst 3750 12 SFP" can serve the purpose?
View 6 Replies View RelatedWhat is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies View RelatedHow i can view the capacity throughput (backplane) of core switches (6509)? How i know much is in use?
View 2 Replies View RelatedDocumentation discusses "1-Gigabit Operation", where all 4 1-Gig SFP's on Sup7L-E are enabled. But it does not say __how__ to select either 10-G or 1-G operational modes.
View 3 Replies View RelatedI upgraded IOS-XE on 4500E (SUP7L-E) to cat4500e-universalk9.SPA.03.03.00.SG.151-1. I encounter the log when i try to issue write mem commad
% VRF table-id 0 not activeCompressed configuration from 8947 bytes to 2140 bytes[OK].
I will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies View RelatedWe are planning for the first installation of 4500 switches containing these supervisor modules. I'm trying to determine the interface numbering convention for ports on the supervisors. Our existing 4500E all have SUP6 modules with twin-gig converters - so I am familiar with the numbering conventions used on those supervisors. How does this change with the software based selection command "hw-module uplink select" used in SUP7?
View 2 Replies View Relatedknow if it is supported connecting the SUP7L-E 10GE ports to a C3KX-NM-10G, using a SFP-H10GB-CU5M (or shorter).
View 3 Replies View Relatedi need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies View RelatedWhat s the fabric speed (backplane speed) of a Nexus 2232 10G EX?What is the forwarding rate (Mpps) of the same 2232 FEX?
View 6 Replies View RelatedTrying to configure 1811w for wi fi . Need to use authentication shared keys but current IOS seems does not support ir
Router(config)#int dot11Radio 0
Router(config-if)#ssid manvee1
Router(config-if-ssid)#a?
% Unrecognized command
Router(config-if-ssid)#
(C181X-ADVIPSERVICESK9-M), Version 12.4(24)T8.
Need to know which IOS will support wi fi and authentication command under dot11 radio 0?
Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedDoes Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedCan nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies View RelatedDoes the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedWhat is a backplane throughput of C3925-SPE100, I tried searching in datasheet but could not find
View 3 Replies View RelatedCoincidentally when i tried to configure router 877 as an adsl router i found that a vlan configuration is included. my question is what is the benefit of using vlans in router ??? i studied that we use it in switches for the purpose of network enhancment from broadcasts and netwrok segmentation. why we use vlans in routers ?
View 9 Replies View RelatedDoes the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies View RelatedDoes this Router Support SIP Forwarding?
View 1 Replies View Relatedwhen the VSS will be supported on Catalyst Supervisor Engine 7-E or 7-LE and on Catalyst 4500-X?And does VSS will require Enterprise license ? or the IP base will be enaugh?
View 7 Replies View Related I have a 3560G switch with c3560-advipservicesk9-mz.122-46.SE and 2 routers. The switch has vlans defined. I want to route all traffic on vlan 25 out of one of the routers exclusively. Here is what I have attempted:
-Set the SDM template to routing & reload
-Define an access-list for the v lan traffic
-Define the route-map
-Apply the route-map to the vlan interface
When I attempt the last step I receive the following syslog error:
%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map RM_IMDGuest not supported for Policy-Based Routing
Also, the route-map is removed from the vlan interface after this error is thrown. Im 99% confident that PBR is supported on this switch (am I wrong?). Here is the relevant show output:...
access-list 125 permit ip 192.168.25.0 0.0.0.255 any
route-map RM_IMDGuest permit 10
match ip address 125
set ip next-hop 192.168.5.3
[code]....
We purchased ME 3400 switch and trying to implement it. But its quite surprising in the ME3400 configuration guide that the switch does not support VTP. When I checked in Feature navigator under feature "VTP" i could see ME3400 supports VTP. But when i get into CLI of ME3400, i am not getting any option of configuring VTP. I could see in some sites VMPS is supported in ME3400.
I would like to confirm the following:
1. Does VTP support present in ME3400 or not? If not, what would be the reason that it is not included in ME3400.
2. If not what is the alternative.
Network is already running VTP of around 30 switches.
I'm trying to get confirmation on whether you can have workgroup bridge mode on the 1040 series model.
The 1041N has the same IOS as the 1141/1241 and it has the settings are there, but I read somewhere on the cisco site that workgroup bridge is only supported on 1100 and 1200 series, is this correct or old information?
Scenario is: I have an existing stand alone 1041N AP, on the other side of the building I have a network LAN switch with a couple of PCs, instead of running cables I would like to add an AP as a bridge to link that switch and PCs to the network that the AP is plugged in to. I believe this is called Workgroup Bridge Mode. In fact there already is a cheap non-cisco wireless device doing this but it is unreliable.
I just placed an order for Two 1041N APs, do I need to change the order to Two 1141N instead?
Also even if the 1041N does not support workgroup bridge mode, can it still act as the ROOT Bridge and have 2 1141N APs configured in bridge mode connected to the 1041N?
We currently have ACE20's, which only support multicast in bridge mode.Was wondering if it's the same on ACE30's, or if Cisco finally implemented support for mcast in routed mode.
View 3 Replies View Relatedis there a support of 1+1 mode (HA mode) at 5508 Controller? If yes Is there a HA bundle or do we have to order two identical 5508 controller ?
View 6 Replies View RelatedThere was this router Cisco 815 that i consoled. I cannot go into its privilege mode. even typing enable still cant go to its # mode. whats the problem with this router? how am i able to fix it? its initial problem was it cannot carry more pc client anymore.. 815 series has a 4 switch port at its back and a wan port.the 4 switch port cannot access the internet if connected to 4 pc clients.
View 5 Replies View RelatedIts required that all ports on nexus 7k should be user configurable as either 1G/10G/FcoE. Which module do i need in this case ?
View 0 Replies View RelatedDoes the Catalyst 3560 support GRE ?
I know that Catalyst 3750X support GRE ,but Catalyst 3750X cannot work in hardware it.
Does the Catalyst 3560 cannot work in hardware too?