Cisco Routers :: RVS 4000 - WAN Abnormal Operation?
Feb 21, 2013
System Information Firmware Version:V2.0.2.7CPU:STAR 9202 Router is operated 2y. No problems till now.There is sometimes abnormal lost of Internet connection, detected by LAN devices. I found it 3 days ago. This dysfunction is occasional 2-5 per day in occasional time.Nothing was changed/upgraded/updated in my WAN cable router or LAN or in the Cisco router. Nothing was changed on computers site (OS,LAN cards, drivers, ...). Just the problem is discovered on the router side.LAN operatation is correct, no problems was founded. Just the devices on LAN lose the internet connection (Win7, Lnx, Mac).
This is status of my WAN - does not matter if the internet connection was lost or not. It is still same:
STATUS-WAN/Gateway
Interface: UP
IP Address is assigned (checked by provider - correct)
Default Gateway and DNSs are assigned too(checked by provider- correct)
What was checked by me:
1. A. I disconnected the cable router from Cable modem
B. I connected the Cable router directly to laptop. Internet connection was right.
2. I called to my Cable provider to check my connection:
- with direct laptop connection to Cable router - Right
- with Cisco router connected to Cable router - Right, but no Internet connection on LAN side behind the Cisco router
3. Standard procedure was tested:
- Unplugged (electricity & cabling) all devices - Cable modem, Cisco router as well.
- Restart of Cable modem, +30 sec. connection of IP cable to Cisco router, start of Cisco router Still same. No Internet connection.
- SETUP/SUMMARY/Network Settings Status - DHCP Release or DHCP Renew was tryed - Still same.After several minutes - was Internet connection Renewed. Just by itself. how?
View 1 Replies
ADVERTISEMENT
May 9, 2013
wether the Cisco RV180 router model can be configured with a public IP address on the LAN interface? I'm planning to use it in the following setup:
Internet ------------- WAN port (public IP) RV180 LAN port(public IP)-------------- WAN(public IP) RV016 LAN (private IP)
Disabling gateway operational mode and switching to router should disable NAT and allow this setup but need to confirm if it works? I'm concerned if the web management interface actually allows a public IP to be set on the LAN side.
View 1 Replies
View Related
Apr 25, 2012
I have my RVS-4000 configured using static IP addresses in the LAN configuration. The users use DHCP to get their addresses (for the most part, a couple may have static IPs set on the computer). I have the maximum number of DHCP users set to 1 to restrict the ability of people to log in to the system. That one address is locked down.
The internal address of the router is set to 182.168.2.1. It doesn't conflict with anything on my network. I have 35 static IPs. About half of them are uing IP Based ACL to limit their access time but that doesn't seem to bear any relationship to what drops off.
Almost daily one or more of the users will lose their IP address and a hard reset of the router is required. The user this happens to seems random and it may be more than one but seldom all of them. The network includes Windows7 (Home & Pro), a FreeNAS, Macs (Leopard and Snow Leopard), iPad, iPods, an iPhone and an AirPort Extreme used as a WAP (DHCP is disabled). The AirPort is plugged directly into the router and has a staic ip on the RVS-4000 but is set to DHCP. It seems to be the most common problem child.
View 3 Replies
View Related
Mar 10, 2012
I attempted to load RVS4000_WRVS4400N_IPS_Signature_v1.50.zip and received an error message "Signature file is not the correct type of version for this device". I have firmware version 1.3.3.5, and and current IPS version 1.42. why IPS v1.5 is rejected?
View 1 Replies
View Related
Nov 16, 2009
I'am using a modem/router to conncet my lan to internet. unfortunetly it is impossible to switch off the router of my modem. So i connect my RVS 4000 on the modem/router and i assign it static ip 192.168.1.10 as my modem has 192.168.1.1. i disable the DHCP function on my RVS 4000. I m still using it because of its gigabit ethernet capability.
My problem is i am unable to connect to my RVS from the outside. inside the LAN no problem I just use its STATIC IP. I have a NAS on this LAN. I write a NAT/PAT rule in my modem/router to route HTTP and FTP and the port for the interface to my NAS. It's just working smoothly. But not for my RVS. I have checked the remote management and translate the traffic incoming on this port to the same port on the 192.168.1.10.Unsuccessfull !!. ok that can't be considered as external traffic.so I disable remote management and all the protection firewall, DOS,BLOCK WAN REQUEST. I route the HTTP port 80 to port 80 192.168.1.10. I try to connect to /home.htm....unsuccessful !!
View 17 Replies
View Related
May 13, 2011
I recently updated my network with the following:
RVS 4000 v1.3.2.0 - Linksys by Cisco version
SG200-26
AP541N [WAP]
All devices have the latest version of firmware.Users only connect laptops via wireless, they are a mix of MAC and Windows users, devices such as printers and network storage are all wired connections.The RVS 4000 would drop the internal Lan after several hours or sometimes days, there would be no reason to the periodicity it would retain and then drop the LAN. By dropping the Lan I mean:
Internet Access would cease, devices such as laptops would lose their wireless connection, a laptop requesting an IP address would be ignored. Effectively we were down.Connecting a laptop to the network via a cable connection would eventually get an IP address but all other wired devices such as the NAS Storage and printers would be unreachable and require powering off and on to get an IP.
A reboot of the RVS 4000 by powering off the router would have to happen to restore the LAN quickly. I followed advice on the Internet and this forum by upgrading the firmware and resetting to factory defaults and then reloading the configuration.The only change that seemed to make any sort of differnece was connecting the AP541N directly to the RVS 4000 rather than the SG200-26. Throughput increased and the period between LAN drops extended but the RVS 4000 would ciontinue dropping the LAN eventually.
When it dropped the LAN during a work day, that was it!I read a lot of negative feedback on the version of RVS 4000 firmware and as the version 2.0 will not install I purchased the Cisco version of the RVS 4000 v 2.0.0.3.
The new RVS 4000 also drops the LAN! The period between drops is much longer, but it still drops the Lan.Ventilation is good and it is sitting on its edge using the platsic feet that come in the package.The AP541N is still directly connected to the RVS 4000 rather than the SG200-26.how to fix the RVS 4000 or an alternative... I would like to stay with Cisco, an alternative, if the RVS 4000 is unfixable should have a browser based admin facility!
View 4 Replies
View Related
Nov 26, 2011
I would like to block IP numbers. When I tried with one the router festively walked straight through it!
View 6 Replies
View Related
Oct 26, 2011
I have an RVS 4000. I have several PC's to which I have assigned static IP addresses. I have recently upgraded most of the PC's to Win 7 (64) machines. I updated the firmware on the RVS4000 to 1.3.3.5 in conjunction with this. After such update (and actually before as well) I could not assign a static IP address to a PC and have access to the internet. It connects fine to my LAN, just no internet access. This is also affected on several other machines running Win XP and Win 2003 Server, so it's not just this computer.
I have:
1. Shut down (powered off/unplugged) everything, router, DSL modem, switches, server, etc.
2. As I said firmware is current.
3. Yes, DNS servers and gateway, subnet, etc. are all correctly specified on the PC.
4. Router is set for gateway mode.
5. Set to only IPV4.
The only way it allows internet access is to use DHCP. I've even tried taking the IP address via DHCP and manually assigning the DNS servers and that works fine, but as soon as I assign a static IP internet access is immediately gone.
There must be something I'm missing, but I can't seem to find it.
Everything worked fine prior to the conversion of the Win 7 machines, i.e. I had several PC's with static IP's and no problems.
View 1 Replies
View Related
Nov 29, 2011
After configuring the router and enabling a load of functions to secure our LAN, the download speed halved! Even disabling AcitveX "eats" 10Mbs! I understand that enabling IPsec will drag the speed down to 25Mbps, but I have disabled this.
Even setting the QoS to speeds equal or higher then the ISP's promissises drags the speed down!
View 2 Replies
View Related
Dec 16, 2011
how to establish tunnel between rvs 4000 and rv042 ?
View 2 Replies
View Related
Jan 4, 2012
RSV 4000 bundle with IPSECVPN. Any additional license for IPSECVPN ?
View 2 Replies
View Related
Jan 17, 2012
This type of issue has been posted time and time again by others. In this particular instance the ability to deny and allow access based on a time and day for one or more MAC id or IP address or range of addresses does not work. Because the code is so "weak" that it cannot handle a policy which passes the midnight threshold into the morning (the test is actually commented out in the code), one is forced to write one, perhaps two inverse permit rule(s). In this case, it cannot be done because the "allow" radio button is stippled out.
Some simple digging reveals that the file AccessRes.htm gets to the browser with the "allow" radio button stippled out because the token "disabled" appears in the generated html.
<input type="radio" value="allow" name="f_status2" onclick="setBLOCK()" disabled="">
I have several of these devices. They are all new V2 units. They all have the latest version of the firmware and they are all broken the same way. This behavior is the same on various flavors of browser. As an experiment, based on SOP responses I've read, I downloaded and flashed with the latest firmware (same version as delivered), and then performed the factory reset. No change. It's broken.
View 1 Replies
View Related
Mar 10, 2012
My RVS 4000 v1 router firmware version 1.3.0.5 has been intermittently going off-line ... a reset of the power resolves the issue temporarly. My plan was to update the firmware but I haven't been able to download an uncorrupted version of the firmware file on the Cisco support site. The file downloads as a zip file but the winzip program says that the file is not in a valid zip format and cannot open it.
View 1 Replies
View Related
Jul 25, 2012
I have HP laserjet 4000 tn. Had an old router and upgraded to a new wireless router, when connecting it to the new router, the port I connect to has the amber light come on. I have reset to factory setting thinking it would reset and capture a new ip address. still giving me problems. try connecting it to my macbook pro and cannot get a "fix" on the printer either. I know it has to do with the configuration of the printer.
View 3 Replies
View Related
Oct 3, 2011
We have an RVS-4000 router that we use as an Internet gateway on our school network. I am trying to set up an Internet Access Policy to block some specific websites by URL using a domain name. I set up the policy, and added a PC to the list using the mac address, and the blocking did not work. I went back to the list and added the IP address of the same PC, the policy still did not work to block the domain. I rebooted the router, cleared the Internet Temporary files and history on the PC, and the policy still does not work. It acts like it is going to block access to the website because it takes a long time, but it will eventually connect.
View 7 Replies
View Related
Dec 1, 2012
This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
View 1 Replies
View Related
Dec 7, 2010
i have been using the ITP7613 system and PA-A3-8E1 IMA.i have question.
Co1#sh int ATM1/0/0ATM1/0/0 is up, line protocol is up Hardware is IMA PA E1, address is 001b.2bf4.cec0 (bia 001b.2bf4.cec0) MTU 4470 bytes, sub MTU 4470, BW 1920000 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255
Co1#sh controller ATM1/0/0ATM1/0/0: Port adaptor specific information Hardware is E1 (1920Kbps) port adaptor Framer is PMC PM7344, SAR is LSI ATMIZER IIScrambling is Enabled Clock Source = INTERNALNational bits = 0x3Flinecode is HDB3E1 Framing Mode: pcm30 ADM formatLBO (Cablelength) is long gain43 120db Facility Alarms: No Alarm
E1 bandwidth of standard is 2048000 Kbit, is this right? But why displayed BW "1920000 Kbit" on ATM1/0/0 interface status and E1(1920K) ?I've never change the Bandwidth option.and As of Cisco IOS Software Release 12.2 (refer to Cisco Bug ID CSCdt57977 (registered customers only) ), the bandwidth displayed on ATM IMA T1 and E1 interfaces is 1536 kbpsand 1920 kbps, respectively.my ITP7613 system has using the 12.2 IOS version.
View 5 Replies
View Related
Apr 27, 2013
We have been having a very abnormal speed issue. This one has me stumped. I am fed up and thinking maybe its an Att issue that will NEVER be resolved.Brother comes and bothers me Zach internet is slow thinking hes just being picky I tell him to reboot his computer. He says its still slow. I run a speed test from my desktop computer I get a 5.36Mbps download and .63 up. I go to his windows xp professional laptop and run a speed test he pulls .63mbps down and .32 up. This is a Dell Latitude D610 with built in wifi. My desktop just so happens to be a wired connectionI grab my laptop which happens to be the exact same model and experience the same result. So I power cycle to modem, then the Linksys ea2700 router. The speeds go back to 5.37m down and normal speed up. Then after 20 minutes its back to a CRAWL.
OK the router MUST be dead. I will kill two birds with one stone. I plug in my Modem/Router combo 2wire 2700. Speed does the same thing starts off fast then slow to a crawl. Figuring it's a laptop issue I use a Linksys wireless USB adapter AE-2500. I get the same result fast then slow. NOW the crazy thing is that its only on my wireless connections. The wireless computers use wireless G and say 54mbps so why would the internet be slow only on the wireless connection.So maybe it's an interference issue So I start up the generator and plug my modem router and laptop into it. I then shut off THE ENTIRE POWER service to my house! I get the same result fast then slow. My neighbors are far apart and I have switched wireless channels and even used the 5ghz frequency with the same results.An ATT Tech says the line is fine. They came to the house and tested everything. The only thing that has happened recently was a storm which left flooding in some parts of town. Only one time was I able to test my WIRED computer and get a download speed of .04Mbps down and .32 up
View 2 Replies
View Related
Mar 27, 2013
I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies
View Related
Feb 11, 2007
The "Wireless Network Monitor" for my Linksys Dual-Band Wireless A+G Notebook Adapter Model No WPC55AG has been unable to run after I last updated my Windows XP machine using Windows Update. The problem presents itself immediately upon login (because the monitor is set to run on startup) with an error window that says "Abnormal program termination" and "WPC55AGV2.exe" in the title bar. I suspect the problem occurred because one of the new updates included an upgrade to the Microsoft .NET Framework Services 3.0.
View 6 Replies
View Related
Jan 18, 2013
A PC from VLAN10 pings another PC in VLAN 20, and another PC between the switch “sales” and the central router is running a protocol analyzer. List all the protocols participating in this operation. You should determine the L2 source/destination addresses and L3 source/destination addresses.
View 10 Replies
View Related
Sep 15, 2011
I have a CUOM 2.3 and CUCM 7.0 installed, we are planned to have a major upgrade to CUCM to 8.5 soon, do i need to upgrade my CUOM ,since CUOM is a Network management system? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license? Is OM 2.3 to 8.X is a direct upgrade?
View 3 Replies
View Related
May 16, 2012
My Customer today have CUOM 2.3 and CUCM 7.1.3. He is planning to do upgrade CUOM 8.6 and CUCM 8.6. My question is: Is it possible to do upgrade CUOM directly to 8.6? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license?
View 4 Replies
View Related
Nov 9, 2011
I am using LMS 4.0 and I keep encountering this issue "Error performing SNMP Operation"
View 5 Replies
View Related
Jun 24, 2012
I have an issue with two APs (3502i) which is associated to controller wism2. Total number of APs are connected to this controller is 422 and once I added two new APs (3502i) to this controller I am unable to see these APs coming up. Getting error messages like wrong primary controller nad secondary controller. When I loggedin to the controller through CLI following are the details I am getting for the APs which is not registering to the controller:, Also for comparison I am attaching the statistics for the AP which is working good and is able to register.
Note: I thought the problem with these two APs and will try replacing them but when i connected the other two APs to different switch and different subnet the same errors we are seeing.
ISSUE with the AP:show ap config general AB2-4N-AP11
Cisco AP Identifier.............................. 440
Cisco AP Name.................................... AB2-4N-AP11
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. -
AP Regulatory Domain............................. Unconfigured
[code]....
View 1 Replies
View Related
Aug 16, 2012
I have a wireless access point/modem at one end of my property (which I cannot relocate). To improve wireless connectivity on the other end of the property I am thinking of placing a wifi repeater (probably a cheap one like http:[URL]... mid-point in the property. However I don't quite understand how these things work. I assume repeaters, extenders, boosters are all the same thing?
Does the repeater actually create a new seperate wifi network, so I will effectively have two wifi networks/SSIDs? or will my wireless devices still see only one wifi network? If it creates two wifi networks what happens when I move through the property with say a laptop, will the laptop need to disconnect from one and reconnect to the other hence interrupting the connection? (which is not ideal).
Also does the repeater take up an IP from my main wireless access point/modem? My setup uses a block of static IPs and hence I would prefer not to waste an IP on the repeater if possible.Homeplugs is something else I'm looking into but that seems to be a more expensive option. With Homeplugs I would disable the wireless on the main access point/modem. Then use the Homeplug to put a wireless access point in the centre of my property hence giving fuller coverage.I've also tried higher DBi antennas (& directional ones) but they have not been effective.
View 1 Replies
View Related
Nov 2, 2010
i have bought (two pro-500 full managed switches, an 541N access point and a RVS4000 router). I have installed the quick vpn which came on the cd rom with my router and as I'm running .windows 7 ultimate 64 I can just not connect. So running through the forums I find out that this is a know problem and that before going further I should run a new VPN client software. Now trying to download I cannot...I have to register..fine...done..... BUT NO now I need a I don't know which service agreement with I don't know who. I have used dozen of routers and networking gear but I have never experienced that for a owned product after registration I can not download an upgrade.
View 3 Replies
View Related
Dec 13, 2011
I have a cat 3750 switch with the folowing snmp v3 config:
-snmp-server group admin v3 priv
-snmp-server user lmsadmin admin v3 auth md5 password1 priv aes 256 password2
The credentials on the device in LMS are as folowing:
where Auth. password = password1 and private password = password2:
When I run a credentials verification job, I get the following error message:
Error performing SNMP operation.
I have tried this on LMS version 4.0 and 4.1 with the same result.
View 2 Replies
View Related
Apr 21, 2013
I want to set up AP 1552 as outdoor access point so serve clients. This AP is connected to 3750X switch and recieving power over ethernet.Now, by default AP 1552 come with bridge mode and it cannot be changed to local mode. I read on one of the post and made it ROOTAP but still the OPER STATUS is down. This device is already registered to my WLC.
what needs to be done to bring the AP in operational status.[code]
View 3 Replies
View Related
Nov 7, 2012
I have an ASA 5510 at V8.2(5) with something near 20 site to site VPN tunnels. I am having a problem with 1 tunnel to a RVS4000. The tunnel is completely closed and reset during Phase2. Here is a small snipet at the time of the tunnel reset
x.x.x.x, Username = x.x.x.x, IP = x.x.x.x, Session disconnected. Session Type: IPsec, Duration: 7h:36m:30s, Bytes xmt: 333755, Bytes rcv: 86281, Reason: User Requested
Followed by Group = x.x.x.x, IP = x.x.x.x, Active unit receives a centry expired event for remote peer x.x.x.x.
We use a number of connection oriented sessions and this blowing them out of the water. all other tunnels are up for DAYS to more than a Month.
View 8 Replies
View Related
Feb 11, 2013
just installed 6 new APs to a client remote site off a 5508 controller. 5508 is running 7.0.116 total of 78 installed APs, mostly 1142's with a dozen or so1242s. All going perfectly until I was about to leave site and noticed two of the APs had no LEDs lit. Checked in the controller, as I had renamed them so knew they were on the system, and they are both there. Connected to each of them and was successful and everything seemed ok - no blue LED though. Rebooted them and the LEDs work as expected during the boot process but as soon as they have entered normal operation the LEDs go dark. urls....but no reports of it with anything other than 3502's.Change process is galacial and heavily monitored so dont want to invoke it if it wont address the concern.
View 10 Replies
View Related
Jun 1, 2010
i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
View 9 Replies
View Related
Nov 7, 2011
I just tested IP SLA with tracking on a 3750 12.2(46)SE. And the configuration was simple enough and tested fine for redundant static routing: [code] Then I tried to do the same on a 3560 switch running 12.2(55)SE3. ip sla went in fine. But when I went to put in the track I was presented with "list boolean and" (for example) after the track and the identifier.I tossed in the ip sla "10" as the object. But shopw track shows the boolean AND as down. I don't get why the track feature is different in two switches so close in IOS version. How do I get the 3560 to track the ip sla as my 3750 does?
View 3 Replies
View Related
