I attempted to load RVS4000_WRVS4400N_IPS_Signature_v1.50.zip and received an error message "Signature file is not the correct type of version for this device". I have firmware version 1.3.3.5, and and current IPS version 1.42. why IPS v1.5 is rejected?
View 1 RepliesI have HP laserjet 4000 tn. Had an old router and upgraded to a new wireless router, when connecting it to the new router, the port I connect to has the amber light come on. I have reset to factory setting thinking it would reset and capture a new ip address. still giving me problems. try connecting it to my macbook pro and cannot get a "fix" on the printer either. I know it has to do with the configuration of the printer.
View 3 Replies View RelatedSystem Information Firmware Version:V2.0.2.7CPU:STAR 9202 Router is operated 2y. No problems till now.There is sometimes abnormal lost of Internet connection, detected by LAN devices. I found it 3 days ago. This dysfunction is occasional 2-5 per day in occasional time.Nothing was changed/upgraded/updated in my WAN cable router or LAN or in the Cisco router. Nothing was changed on computers site (OS,LAN cards, drivers, ...). Just the problem is discovered on the router side.LAN operatation is correct, no problems was founded. Just the devices on LAN lose the internet connection (Win7, Lnx, Mac).
This is status of my WAN - does not matter if the internet connection was lost or not. It is still same:
STATUS-WAN/Gateway
Interface: UP
IP Address is assigned (checked by provider - correct)
Default Gateway and DNSs are assigned too(checked by provider- correct)
What was checked by me:
1. A. I disconnected the cable router from Cable modem
B. I connected the Cable router directly to laptop. Internet connection was right.
2. I called to my Cable provider to check my connection:
- with direct laptop connection to Cable router - Right
- with Cisco router connected to Cable router - Right, but no Internet connection on LAN side behind the Cisco router
3. Standard procedure was tested:
- Unplugged (electricity & cabling) all devices - Cable modem, Cisco router as well.
- Restart of Cable modem, +30 sec. connection of IP cable to Cisco router, start of Cisco router Still same. No Internet connection.
- SETUP/SUMMARY/Network Settings Status - DHCP Release or DHCP Renew was tryed - Still same.After several minutes - was Internet connection Renewed. Just by itself. how?
I have my RVS-4000 configured using static IP addresses in the LAN configuration. The users use DHCP to get their addresses (for the most part, a couple may have static IPs set on the computer). I have the maximum number of DHCP users set to 1 to restrict the ability of people to log in to the system. That one address is locked down.
The internal address of the router is set to 182.168.2.1. It doesn't conflict with anything on my network. I have 35 static IPs. About half of them are uing IP Based ACL to limit their access time but that doesn't seem to bear any relationship to what drops off.
Almost daily one or more of the users will lose their IP address and a hard reset of the router is required. The user this happens to seems random and it may be more than one but seldom all of them. The network includes Windows7 (Home & Pro), a FreeNAS, Macs (Leopard and Snow Leopard), iPad, iPods, an iPhone and an AirPort Extreme used as a WAP (DHCP is disabled). The AirPort is plugged directly into the router and has a staic ip on the RVS-4000 but is set to DHCP. It seems to be the most common problem child.
I'am using a modem/router to conncet my lan to internet. unfortunetly it is impossible to switch off the router of my modem. So i connect my RVS 4000 on the modem/router and i assign it static ip 192.168.1.10 as my modem has 192.168.1.1. i disable the DHCP function on my RVS 4000. I m still using it because of its gigabit ethernet capability.
My problem is i am unable to connect to my RVS from the outside. inside the LAN no problem I just use its STATIC IP. I have a NAS on this LAN. I write a NAT/PAT rule in my modem/router to route HTTP and FTP and the port for the interface to my NAS. It's just working smoothly. But not for my RVS. I have checked the remote management and translate the traffic incoming on this port to the same port on the 192.168.1.10.Unsuccessfull !!. ok that can't be considered as external traffic.so I disable remote management and all the protection firewall, DOS,BLOCK WAN REQUEST. I route the HTTP port 80 to port 80 192.168.1.10. I try to connect to /home.htm....unsuccessful !!
I recently updated my network with the following:
RVS 4000 v1.3.2.0 - Linksys by Cisco version
SG200-26
AP541N [WAP]
All devices have the latest version of firmware.Users only connect laptops via wireless, they are a mix of MAC and Windows users, devices such as printers and network storage are all wired connections.The RVS 4000 would drop the internal Lan after several hours or sometimes days, there would be no reason to the periodicity it would retain and then drop the LAN. By dropping the Lan I mean:
Internet Access would cease, devices such as laptops would lose their wireless connection, a laptop requesting an IP address would be ignored. Effectively we were down.Connecting a laptop to the network via a cable connection would eventually get an IP address but all other wired devices such as the NAS Storage and printers would be unreachable and require powering off and on to get an IP.
A reboot of the RVS 4000 by powering off the router would have to happen to restore the LAN quickly. I followed advice on the Internet and this forum by upgrading the firmware and resetting to factory defaults and then reloading the configuration.The only change that seemed to make any sort of differnece was connecting the AP541N directly to the RVS 4000 rather than the SG200-26. Throughput increased and the period between LAN drops extended but the RVS 4000 would ciontinue dropping the LAN eventually.
When it dropped the LAN during a work day, that was it!I read a lot of negative feedback on the version of RVS 4000 firmware and as the version 2.0 will not install I purchased the Cisco version of the RVS 4000 v 2.0.0.3.
The new RVS 4000 also drops the LAN! The period between drops is much longer, but it still drops the Lan.Ventilation is good and it is sitting on its edge using the platsic feet that come in the package.The AP541N is still directly connected to the RVS 4000 rather than the SG200-26.how to fix the RVS 4000 or an alternative... I would like to stay with Cisco, an alternative, if the RVS 4000 is unfixable should have a browser based admin facility!
I would like to block IP numbers. When I tried with one the router festively walked straight through it!
View 6 Replies View RelatedI have an RVS 4000. I have several PC's to which I have assigned static IP addresses. I have recently upgraded most of the PC's to Win 7 (64) machines. I updated the firmware on the RVS4000 to 1.3.3.5 in conjunction with this. After such update (and actually before as well) I could not assign a static IP address to a PC and have access to the internet. It connects fine to my LAN, just no internet access. This is also affected on several other machines running Win XP and Win 2003 Server, so it's not just this computer.
I have:
1. Shut down (powered off/unplugged) everything, router, DSL modem, switches, server, etc.
2. As I said firmware is current.
3. Yes, DNS servers and gateway, subnet, etc. are all correctly specified on the PC.
4. Router is set for gateway mode.
5. Set to only IPV4.
The only way it allows internet access is to use DHCP. I've even tried taking the IP address via DHCP and manually assigning the DNS servers and that works fine, but as soon as I assign a static IP internet access is immediately gone.
There must be something I'm missing, but I can't seem to find it.
Everything worked fine prior to the conversion of the Win 7 machines, i.e. I had several PC's with static IP's and no problems.
After configuring the router and enabling a load of functions to secure our LAN, the download speed halved! Even disabling AcitveX "eats" 10Mbs! I understand that enabling IPsec will drag the speed down to 25Mbps, but I have disabled this.
Even setting the QoS to speeds equal or higher then the ISP's promissises drags the speed down!
how to establish tunnel between rvs 4000 and rv042 ?
View 2 Replies View RelatedRSV 4000 bundle with IPSECVPN. Any additional license for IPSECVPN ?
View 2 Replies View RelatedThis type of issue has been posted time and time again by others. In this particular instance the ability to deny and allow access based on a time and day for one or more MAC id or IP address or range of addresses does not work. Because the code is so "weak" that it cannot handle a policy which passes the midnight threshold into the morning (the test is actually commented out in the code), one is forced to write one, perhaps two inverse permit rule(s). In this case, it cannot be done because the "allow" radio button is stippled out.
Some simple digging reveals that the file AccessRes.htm gets to the browser with the "allow" radio button stippled out because the token "disabled" appears in the generated html.
<input type="radio" value="allow" name="f_status2" onclick="setBLOCK()" disabled="">
I have several of these devices. They are all new V2 units. They all have the latest version of the firmware and they are all broken the same way. This behavior is the same on various flavors of browser. As an experiment, based on SOP responses I've read, I downloaded and flashed with the latest firmware (same version as delivered), and then performed the factory reset. No change. It's broken.
My RVS 4000 v1 router firmware version 1.3.0.5 has been intermittently going off-line ... a reset of the power resolves the issue temporarly. My plan was to update the firmware but I haven't been able to download an uncorrupted version of the firmware file on the Cisco support site. The file downloads as a zip file but the winzip program says that the file is not in a valid zip format and cannot open it.
View 1 Replies View RelatedWe have an RVS-4000 router that we use as an Internet gateway on our school network. I am trying to set up an Internet Access Policy to block some specific websites by URL using a domain name. I set up the policy, and added a PC to the list using the mac address, and the blocking did not work. I went back to the list and added the IP address of the same PC, the policy still did not work to block the domain. I rebooted the router, cleared the Internet Temporary files and history on the PC, and the policy still does not work. It acts like it is going to block access to the website because it takes a long time, but it will eventually connect.
View 7 Replies View RelatedThis is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
I have Counterstrike Scource and am wanting to setup a deticated server. I have a netgear router with 27015 port open and my nat type is open, however it keeps on giving me the "steam validation rejected" error. BTW it works fine on LAN, just not online.
View 2 Replies View RelatedI have the Netgear 4000 as primary router and I want to connect my second router WRT54GL running tomato firmware to my network.
View 2 Replies View RelatedMy home is CAT-5 ready, so I am using the RSV-4000 firewall router. I just bought a WIFI IPad2, so I need to add wireless. What would be the best CISCO/Linksys solution?I really like the added security of using the wired connection, besides, the PC's in my house do not move around. I just need the WIFI for the IPad.
View 1 Replies View RelatedI have my RVS-4000 configured using static IP addresses in the LAN configuration. The users use DHCP to get their addresses (for the most part, a couple may have static IPs set on the computer). I have the maximum number of DHCP users set to 1 to restrict the ability of people to log in to the system. That one address is locked down.
Almost daily one or more of the users will lose their IP address and a hard reset of the router is required. The user this happens to seems random and it may be more than one but seldom all of them. The network includes Windows7 (Home & Pro), a FreeNAS, Macs (Leopard and Snow Leopard) and an AirPort Extreme used as a WAP (DHCP is disabled). The AirPort is plugged directly into the router and has a staic ip on the RVS-4000 but is set to DHCP. It seems to be the most common problem child.
If something is rejected from the RAT and needs to be fixed..you would add to RAT or Relay list or...
View 12 Replies View RelatedI am using a Cisco RVS 4000 to test a new 10M/10M internet connection. I'm having a small problem performing the ISP's speed test (speedtest.cavtel.net). The download test consistently gives me 10Mbit/s, full speed for the connection, however the upload speed is usually about 5.5 Mbit/s. My ISP has been onsite and has checked the lines and tested directly, and we have determined that if connected directly we can test to full upload speeds, but when the RVS is connected, we cannot get full speed.
We've tried different cables, reseting to factory defaults, updating firmware, changing port settings, and toggling most of the other setting on the router. Some settings do have a minor effect on the upload speed, but nothing that gets me back up to 10Mbit/s.
I did notice that there appears to be no way to set speed and negotiation settings on the WAN port. Perhaps I am missing it, because that seems like a possible culprit.
Otherwise, the only only thing I can think of is a warranty return to determine if the unit itself is defective.
i received the below output,how to start a troubleshooting? the aaa server is cisco ACS 5.3
ERROR: Authentication Rejected: Unspecified.
I recently purchased a rvs 4000 wired linksys router for my business. Everything works great with the exception of my VOIP PBX server. I can receive a call and make a call one at a time. If a second line rings in and is picked up the first call and the second go dead air. I am sure that it is a security setting somewhere that I just can't seem to figure out. I sure would like to get some direction on this.
View 2 Replies View RelatedI have a Swann Communication security camera system with their DVR8-4000 hooked to an IPv4 router, connected to the Internet using the new HughesNet Gen4 service. The Swann DVR wired to my router requires a static IP address. HughesNet Gen4 is implemented with IPv6 and I am told that it does not accommodate an IPv4 type static address.
I have discussed the issue with both company’s technical support. HughesNet Gen4 reps recognize the issue and may support static addressing in the future, but not now. Swann reps will not modify their implementation because of the relatively small Gen4 market. The Swann rep suggested that replacing my IPv4 router with an IPv6 router might resolve the “static IP address” issue.I am looking at several Linksys IPv6 routers including the EA4500 SMART WiFi Wireless Router N900, but know too little about IPv4, IPv6 and router/static addressing to proceed unassisted.
1) can I implement a static address with an Linksys IPv6 router cdonnected to Gen4?
2) Which Linksys routers offer IPv6 support?
3) How does one go about setting an IPv6 static address using HughesNet Gen4 on a Linksys router?
recently i do some lab about trunking protocol using Layer 3 switch C3560 and layer 2 switch C2960, but i face a problem that i cannot configure trunk port on my C3560 using "switchport mode trunk" command, and after looking for the answer from google i found that i have to "remove" the "auto" mode of C3560 using "switchport mode dynamic desirable" and after that we can enter the "switcport mode trunk" command successfully.
and my question are, whether the "auto" trunk mode in switch layer 3 is a default mode or not? and why i should enter "sw mode dynamic desirable" command before "sw mo trunk" command ?
I am deploying a Cisco 1841 in place of our basic DSL router.I have an ADSL WIC and FA0/0 connected to our LAN.LAN IP ADDRESS range is 192.168.1. 0/ 24 I have dynamic and static NAT configured. At this point although I have ACL's configured I have NOT implemented them as yet for the following reason. I am unable to recieve inbound SMTP traffic - now know my MX records are correct as this all owrks happily on our basic DSL router. I can send external emails no problem and all internal email works fine. [code] I am in the process of defaulting the router and programming the barbones to get the link working and see if inbound SMTP works then start building the blocks again.
View 4 Replies View RelatedWe are setting up a WLC 7500 for the first time and are having a hard time trying to connect an LAP to the WLC. We have 1042 Access Points.Reason for last unsucessful attempt: to many concurrent ap image downloads
-Last Error Occurred: Lwapp discovery request rejected
-Last Error Occurred Reason: Too many concurrent AP image downloads
We only have 1 AP plugged in so far and it does recieve an IP address from DHCP.
I just configure VPN for end users in PIX515e with IOS 8 and get stuck with "Tunnel Rejected: User (msveden) not member of group (VPN-shared), group-lock check failed.". tell me how I add user to my VPN group?
View 1 Replies View RelatedIm trying to simulate a switch in Gns3 and i use 16ESW module in a cisco 3700 router. why im getting this record after i try to filter which vlans pass through my trunk port:Router(config-if)#switchport trunk allowed vlan 2,3,4 Command rejected: Bad VLAN allowed list. You have to include all default vlans, e.g. 1-2,1002-1005.
View 6 Replies View RelatedWe are using WLC4402 for our Aironet 1240AG access points. The clients are connecting to the access points and are authenticating to the RADIUS server. I am seeing the logs in Server 2008 but they are being rejected due to Network Policy on the NPS server.
Where do I see the Authentication Type on the WLC4400 or the 1240's? In order for the clients (authenticated via Active Directory user) I have to set the Authentication in the NPS Connection Request Policy to "Allow clients to connect without negotiating an authentication method".
I do not have a certificate on the server and my method options are MS-CHAP-v2, MS-CHAP, CHAP, PAP, SPAP, and allow without negotiating. This RADIUS server was moved from Server 2003 IAS to Server 2008 NPS and there were no issues in Server 2003 IAS. I have all authentication methods allowed and it still gives me the error below. Only when I check "Allow clients to connect without negotiating an authentication method" it allows the authentication to proceed.
Client Machine:
Security ID: NULL SID Account Name: Fully Qualified Account Name: OS-Version:
Called Station Identifier: 00-17-a2-87-54-00: SSID NAME
Calling Station Identifier: 00-41-96-b6-e3-27
NAS:
NAS IPv4 Address: 192.168.90.24
NAS IPv6 Address: -
[code]...
Reason: The user attempted to use an authentication method that is not enabled on the matching network policy.
i have bought (two pro-500 full managed switches, an 541N access point and a RVS4000 router). I have installed the quick vpn which came on the cd rom with my router and as I'm running .windows 7 ultimate 64 I can just not connect. So running through the forums I find out that this is a know problem and that before going further I should run a new VPN client software. Now trying to download I cannot...I have to register..fine...done..... BUT NO now I need a I don't know which service agreement with I don't know who. I have used dozen of routers and networking gear but I have never experienced that for a owned product after registration I can not download an upgrade.
View 3 Replies View RelatedI have an ASA 5510 at V8.2(5) with something near 20 site to site VPN tunnels. I am having a problem with 1 tunnel to a RVS4000. The tunnel is completely closed and reset during Phase2. Here is a small snipet at the time of the tunnel reset
x.x.x.x, Username = x.x.x.x, IP = x.x.x.x, Session disconnected. Session Type: IPsec, Duration: 7h:36m:30s, Bytes xmt: 333755, Bytes rcv: 86281, Reason: User Requested
Followed by Group = x.x.x.x, IP = x.x.x.x, Active unit receives a centry expired event for remote peer x.x.x.x.
We use a number of connection oriented sessions and this blowing them out of the water. all other tunnels are up for DAYS to more than a Month.
So all of a sudden the trusty HP 4000 stopped printing. A little bit of troubleshooting and I found out that the problem was the JetDirect card. I purchased a new one (615n - same model as the old one), installed it, ran a printer configuration page, confirming I have an IP (192.168.x.x) and subnet mask (255.255.255.0), config by DHCP.Also, ran a ping test and it appears to be fine?
View 1 Replies View Related