Cisco Wireless :: 7500 LAP Won't Join WLC / Lwapp Discovery Request Rejected
Sep 20, 2011
We are setting up a WLC 7500 for the first time and are having a hard time trying to connect an LAP to the WLC. We have 1042 Access Points.Reason for last unsucessful attempt: to many concurrent ap image downloads
-Last Error Occurred: Lwapp discovery request rejected
-Last Error Occurred Reason: Too many concurrent AP image downloads
We only have 1 AP plugged in so far and it does recieve an IP address from DHCP.
View 15 Replies
ADVERTISEMENT
Sep 10, 2012
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies
View Related
Jan 13, 2013
Im receving this error on my syslog server: capwap_ac_sm.c:1443 Ignoring Primary discovery request received on non-management interface (2) from APalready checked the configuration and everything seems ok. They are registered and with clients associated.What could be the cause?
View 2 Replies
View Related
Aug 10, 2011
Trying to get an lightweight AP to register with a controller, never seen this one before where the Discovery request is going out to the controller, the discovery response is coming back, but then nothing. At this point the AP should then send a JOIN request, but it just doesnt.
I am using L3 LWAPP, and have the AP statically configured. its a 1131, connecting to a 5.1.151.0 in a WISM. I have run a wireshark and can see the discovery going out, its response coming back, but then nothing (the debugs below also back this up). I have also jumped on the controller and can see the discovery responces are going out but it says no JOIN's are coming in. I'm aware this is an old version of controller but still..
I've tried many different IOS on the AP, including the one it came with in the box, other previously successful IOS and the IOS that 5.1.151.0 dishes out to its registered AP's, multiple AP hardware resets, controller reboots, tried different controllers. etc... What would cause this? Possibly something in the response? See info below:
AP
LWAPP Static IP Configuration
IP Address 172.18.240.244
IP netmask 255.255.255.192
Default Gateway 172.18.240.193
[Code]....
View 8 Replies
View Related
May 10, 2012
We are using WLC4402 for our Aironet 1240AG access points. The clients are connecting to the access points and are authenticating to the RADIUS server. I am seeing the logs in Server 2008 but they are being rejected due to Network Policy on the NPS server.
Where do I see the Authentication Type on the WLC4400 or the 1240's? In order for the clients (authenticated via Active Directory user) I have to set the Authentication in the NPS Connection Request Policy to "Allow clients to connect without negotiating an authentication method".
I do not have a certificate on the server and my method options are MS-CHAP-v2, MS-CHAP, CHAP, PAP, SPAP, and allow without negotiating. This RADIUS server was moved from Server 2003 IAS to Server 2008 NPS and there were no issues in Server 2003 IAS. I have all authentication methods allowed and it still gives me the error below. Only when I check "Allow clients to connect without negotiating an authentication method" it allows the authentication to proceed.
Client Machine:
Security ID: NULL SID Account Name: Fully Qualified Account Name: OS-Version:
Called Station Identifier: 00-17-a2-87-54-00: SSID NAME
Calling Station Identifier: 00-41-96-b6-e3-27
NAS:
NAS IPv4 Address: 192.168.90.24
NAS IPv6 Address: -
[code]...
Reason: The user attempted to use an authentication method that is not enabled on the matching network policy.
View 2 Replies
View Related
Nov 12, 2011
If something is rejected from the RAT and needs to be fixed..you would add to RAT or Relay list or...
View 12 Replies
View Related
Mar 10, 2012
I attempted to load RVS4000_WRVS4400N_IPS_Signature_v1.50.zip and received an error message "Signature file is not the correct type of version for this device". I have firmware version 1.3.3.5, and and current IPS version 1.42. why IPS v1.5 is rejected?
View 1 Replies
View Related
Mar 14, 2012
i received the below output,how to start a troubleshooting? the aaa server is cisco ACS 5.3
ERROR: Authentication Rejected: Unspecified.
View 1 Replies
View Related
Apr 5, 2013
is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies
View Related
Sep 12, 2011
I am trying to upgrade an autonomous IOS 1242 AP to LWAPP and I am having an issue with finding the right code to complete the upgrade. I have upgraded the AP to c1240-rcvk9w8-tar.124-21a.ja2.tar, but now I think I need a JX version of code to have it join a controller, and I can't find this anywhere on the Cisco site.
View 5 Replies
View Related
Dec 3, 2008
Can the AIR-WLC526-K9 be used for any other access points besides the AIR-LAP521G-A-K9 access points? Does the 526 controller use the LWAPP protocol?
View 3 Replies
View Related
Apr 16, 2012
recently i do some lab about trunking protocol using Layer 3 switch C3560 and layer 2 switch C2960, but i face a problem that i cannot configure trunk port on my C3560 using "switchport mode trunk" command, and after looking for the answer from google i found that i have to "remove" the "auto" mode of C3560 using "switchport mode dynamic desirable" and after that we can enter the "switcport mode trunk" command successfully.
and my question are, whether the "auto" trunk mode in switch layer 3 is a default mode or not? and why i should enter "sw mode dynamic desirable" command before "sw mo trunk" command ?
View 5 Replies
View Related
Oct 5, 2011
I have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies
View Related
Oct 15, 2012
What is the difference between WIRELESS LAN LWAPP and WIRELESS LAN LWAP RECOVERY images? I believe the RECOVERY is used in the upgade process - but what is the other used for?
View 1 Replies
View Related
Jan 24, 2012
We have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
View 4 Replies
View Related
Nov 14, 2012
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
View 8 Replies
View Related
Jan 14, 2012
I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies
View Related
Jan 29, 2013
I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies
View Related
May 22, 2012
I need to upgrade several 1252s from autonomous to LWAPP. I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade. I wil be using NCS to do final configuration once the APs come online.
View 1 Replies
View Related
Aug 25, 2011
I would like to know AIR-AP1252AG-A-K9 (Autonomous AP) can be changed to LWAPP AP by changing IOS image??
View 1 Replies
View Related
Jul 27, 2011
I try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies
View Related
Feb 26, 2013
I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
View 2 Replies
View Related
Aug 5, 2012
i have lwapp 1130 in internal network , i already configure dhcp with option 43, in my switch connected to ap i set vlan 1424 for management AP and the ap got ip addres from dhcp server. The wlc controller is in DMZ with ip 10.222.5.3, from switch connected to ap i can ping 10.222.5.3 , it aslo seperated by cisco asa firewall, i already set allow from 0.0.0.0 to 10.222.5.3 udp port 5246-5247 and 12222-12223.
View 4 Replies
View Related
Jan 10, 2011
I am deploying a Cisco 1841 in place of our basic DSL router.I have an ADSL WIC and FA0/0 connected to our LAN.LAN IP ADDRESS range is 192.168.1. 0/ 24 I have dynamic and static NAT configured. At this point although I have ACL's configured I have NOT implemented them as yet for the following reason. I am unable to recieve inbound SMTP traffic - now know my MX records are correct as this all owrks happily on our basic DSL router. I can send external emails no problem and all internal email works fine. [code] I am in the process of defaulting the router and programming the barbones to get the link working and see if inbound SMTP works then start building the blocks again.
View 4 Replies
View Related
Feb 20, 2012
After upgrading, ping times from clients has gone from ~10ms to ~2500ms. I have a Cisco 7500 Flex controller, when running controller code version 7.0.220.0 client performance was as expected. When using code 7.2.103.0 performance is terrible. I have tried upgrade to 7.2.103.0 and clean configuration (reset) with 7.2.103.0 with the same results.
I have tested using 3502i APs with the signal metrics (from AP) reported by the clients (all testing close to these figures):
Signal Strength : -48 dBm
Signal to Noise : 49 dB
AP's are in HREAP/Flex mode. The WLANs use HREAP/FlexConnect local switching. I have tested WLAN's with WPA2-PSK and 802.1x/WPA2 with the same results. I have tested several clientsoperatign systems , laptops, ipads, iphone. All experience consitent poor ping latency peformance on both 2.4Ghz and 5 Ghz when using controller code 7.2.103.0.
I have switched between 7.0.220.0 and 7.2.103.0 several times and the results are consistent; good performance on 7.0.220.0 and terrible performance on 7.2.103.0. I would like to use 7.2.103.0 for its enhanced FlexConnect features but this is a real show stopper.
View 8 Replies
View Related
Sep 5, 2011
I have a Cisco controller WLAN solution where I want to bridge traffic locally on a remote site, when using Cisco 1140 LWAPP.Is the only way H-REAP ?
View 3 Replies
View Related
Aug 25, 2010
upgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies
View Related
Oct 10, 2011
I'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.
View 5 Replies
View Related
Sep 11, 2011
some days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies
View Related
Jan 21, 2012
I have a lwapp 1130 here and it's no longer associated with the controller. I issued the clear lwapp private-config, it went through and cleared the config. Now when I try to issue the lwapp commands to set the ip and such i get ERROR!!! Command is disabled. I read that this means the static configuration is locked, but it did not say how to "unlock" it. how to get this re-enabled.
View 31 Replies
View Related
Jan 21, 2013
We are connecting a cisco router (819) to wireless lan network (lwapp) through its wireless interface.
clients ---> 819 ---->AP (WGB) ------ lwapp ----- AP ---> LAN ---> servers.
since the clients are on the same subnet as the the VLAN on the lwapp, everything works great.When we add a new L3 VLAN on the 819 router, and we try to ping the clients from the servers, the packets can reach the clients but never received by the servers back. it seems like the bridge is dropping the packets when they go back from the client to the servers.when we use a GRE tunnel from the 819 to the LAN, everything works great.
View 3 Replies
View Related
Aug 19, 2010
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
View 4 Replies
View Related
Jul 22, 2012
I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
View 3 Replies
View Related
