Im trying to simulate a switch in Gns3 and i use 16ESW module in a cisco 3700 router. why im getting this record after i try to filter which vlans pass through my trunk port:Router(config-if)#switchport trunk allowed vlan 2,3,4 Command rejected: Bad VLAN allowed list. You have to include all default vlans, e.g. 1-2,1002-1005.
View 6 RepliesI cant find the v LAN-membership command on my 3700 layer 3 switch, I've searched Google on whether the command has upgraded to a new syntax to no avail, I'm using GNS3 and the IOS is c3725-adventerprisek9-mz.124-25d.bin
View 4 Replies View RelatedNot sure why the N7K M1 card doesn't take this command. It works on other N7K at different site. [code]
View 1 Replies View RelatedI am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.
View 24 Replies View RelatedExtended IP access list VLAN20
10 permit tcp any any established
11 permit icmp any any
20 permit tcp any 192.168.20.0 0.0.0.255 eq 80
30 permit tcp any 192.168.20.0 0.0.0.255 eq 443
40 deny ip any any log
[code].....
Above is the network diagram and access list for VLAN 20 and VLAN 30, applied on incoming direction of each valn.But still able to access other port which is not on access list, tried changing the direction with no luck.Inter vlan routing is enabled on CoreSwitch default router is 192.168.10.10
I have a LIII Switch Cisco 3750x ,with diffrent Vlans , Some users are in Vlan 102 (10.10.2.0) and Some Users are in Vlan1 (10.10.1.0) , now i want to restrict the Vlan102 users to access Vlan1 , i am pasting my configuration below , how to create a access list .
interface Vlan1
ip address 10.10.1.36 255.255.255.0
ip helper-address 10.10.1.36
[Code].....
In my core Switch,there are 2 v LAN(V LAN 1 & V LAN 2)my switch is Cisco 4948,so be default ip routing is enable in it. My all servers (DHCP,HTTP,HTTPS) are in v LAN 1 & internet is also in v LAN 1.
My requirement is that v LAN 1 user should not communicate with the v LAN 2 and vice versa. But the v LAN 2 users need an access of all servers and internet which is in v LAN 1. How to configure the access-list. I have try on Packet tracer which i have attached.
note:v LAN 2 user should get the IP from dhcp server which is in vlan1.
recently i do some lab about trunking protocol using Layer 3 switch C3560 and layer 2 switch C2960, but i face a problem that i cannot configure trunk port on my C3560 using "switchport mode trunk" command, and after looking for the answer from google i found that i have to "remove" the "auto" mode of C3560 using "switchport mode dynamic desirable" and after that we can enter the "switcport mode trunk" command successfully.
and my question are, whether the "auto" trunk mode in switch layer 3 is a default mode or not? and why i should enter "sw mode dynamic desirable" command before "sw mo trunk" command ?
my environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
Users behind a Cisco 1841 are not able to connect to a network using the Cisco Systems VPN Client. Transport is IP sec over UDP (NAT/PAT). Connection just times out.
Which ports should be allowed in the access list? Or do you have an link to a article for this?
Me and my friend is currently setting up a Xen test environment. As you can se from the picture below we are running a Cisco ASA 5505 to reach the network from the outside.But the problem is that we want to reach the virtual pfSense's subnet's through the Cisco AnyConnect VPN. And currently the pfSense's are only configured with a public ip and a virtual interface to the VM's.could solve this problem by buying another PCI NIC, so that we have a physical link from the "pfSense box" to a tagged VLAN on the switch.But we are having problems configuring the switch to general vlan's. Cause Xen can't have it's management interface on a tagged VLAN directly from the XenServer,but the switch can tag the packet when it reaches the switchport. I would like to have "switch port general allowed vlan 2" for admin and 10 for "LAN"And then trunk the port to the Cisco ASA. But again, Xen stops me from doing this.
View 2 Replies View RelatedI have a Nexus 7000 Core Switch , and i need to allow the domain controller ip 10.x.x.x for DHCP relay on switch.
View 2 Replies View RelatedI have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies View RelatedBoss wants a listing of the firewall rules only. What's a command I can run that will give me a listing of this?If I can get an output of firewall rules only, via GUI, that'll work too. It just needs to end up with a printout on a piece of paper telling me what the firewall is doing.
View 17 Replies View RelatedOur company had been buying Cisco 1841 routers for years and they have served us well. The 1841 was discontinued and instead we have now purchased a Cisco 1921. It is brand new, running "Version 15.0(1r)M15" of IOS ("usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" file).
On our older Cisco 1841 routers, we would always prioritize certain TCP and UDP packets using the priority-list command. However, I have suddenly discovered that priority-list is not available on this brand new router. (?) I am unsure why. I did some reading and according to the document [URL], and priority-group are unsupported in Cisco IOS 15.
Later version of a product isn't as fully-featured as the earlier version. I want to prioritize the following type of network traffic.
UDP ports 8000 through 8063, 2427, 2727, 9300, 9301
TCP port 35300, 60001 through 60010, 2065, 33333, 3065
giving them a higher priority than the rest of other packets. This is necessary for our vendor's VoIP implementation. These packets should be "high" priority; everything else can be "medium."
How to delete run command dropdown list
View 1 Replies View Relatedis there a cisco command to check the list of incoming vlans on a catalyst 4640 or at least that will give you the same output?we're having an issue with an ethernet circuit, links are up but ping won't go through(no ACLs) and I want to see if the vlan tag from the the other side(side B) is properly reaching side A.
View 1 Replies View RelatedBetween our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies View RelatedI am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
I want to send a particular data stream (source-A destination-B) through only one of two WAN routers to a remote site. The remote site also has two WAN routers. Traffic from source-A will travel through a core and distribution layer of 6500 L3 switches, running 12.2(33)SXH8, to the WAN routers which are two ASR1006s. The remote end is the same - two ASR1006 WAN routers to 6500 distribution and Core L3 switches. All 6500s are L3 uplinked to each other and to the WAN routers. All traffic from the local site to the remote site routes throuh only one of the two WAN routers. I want to move only traffic from source-A to source-B to the second WAN router to the remote site.
Would it be best to use policy-based routing or an offset list of some sort to accomplish this? I've done PBR before where you just hand off traffic described in an ACL to a particular outbound port and basically hand carry the traffic to a point in the network where EIGRP prefers the route you want.
I'm looking to implement a vlan filter to keep unnecessary stuff off my access-layer. Things like IPv6, IPX etc. I really only want IPv4, ARP and 802.1q on these 4500s. I know on 3750, 3560s etc, when I create the mac access-list, I can do it by ethertype, but on the 4500, I dont have that option.
4th_floor(config)#mac access-list extended Drop-traffic
4th_floor(config-ext-macl)#permit any any ?
protocol-family An Ethernet protocol family
<cr>
4th_floor(config-ext-macl)#permit any any protocol-family ?
appletalk
arp-non-ipv4
decnet
[Code]....
I have an 1800 isr that is running with port forwarding only. It is running a series of ip nat inside source static address port address port commands. It does not have an access list bound to the outside interface. This is working fine, but i am wondering if this is a security concern?
View 1 Replies View RelatedThe last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
How to apply access list on Vlans ?
my Scenario is
13 Vlans in cisco 3560 switch (Vlan 10,20,30........ 130)
vlan 10 ---- ip range 192.168.10.0/24 interface vlan 10 ip add : 192.168.10.1
vlan 20 ---- ip range 192.168.20.0/24 interface vlan 20 ip add : 192.168.20.1
here i want to block vlan 10 access to vlan 20 i created extended access list deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
and applied in interface vlan 10 as out now i cant able to access any host in vlan 20 (host 192.168.20.1) but i can able ping vlan 20's gateway 192.168.20.1
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
I have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000