Cisco WAN :: ITP7613 / PA-A3-8E1 IMA - Abnormal Bandwidth Display?
Dec 7, 2010
i have been using the ITP7613 system and PA-A3-8E1 IMA.i have question.
Co1#sh int ATM1/0/0ATM1/0/0 is up, line protocol is up Hardware is IMA PA E1, address is 001b.2bf4.cec0 (bia 001b.2bf4.cec0) MTU 4470 bytes, sub MTU 4470, BW 1920000 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255
Co1#sh controller ATM1/0/0ATM1/0/0: Port adaptor specific information Hardware is E1 (1920Kbps) port adaptor Framer is PMC PM7344, SAR is LSI ATMIZER IIScrambling is Enabled Clock Source = INTERNALNational bits = 0x3Flinecode is HDB3E1 Framing Mode: pcm30 ADM formatLBO (Cablelength) is long gain43 120db Facility Alarms: No Alarm
E1 bandwidth of standard is 2048000 Kbit, is this right? But why displayed BW "1920000 Kbit" on ATM1/0/0 interface status and E1(1920K) ?I've never change the Bandwidth option.and As of Cisco IOS Software Release 12.2 (refer to Cisco Bug ID CSCdt57977 (registered customers only) ), the bandwidth displayed on ATM IMA T1 and E1 interfaces is 1536 kbpsand 1920 kbps, respectively.my ITP7613 system has using the 12.2 IOS version.
View 5 Replies
ADVERTISEMENT
Feb 21, 2013
System Information Firmware Version:V2.0.2.7CPU:STAR 9202 Router is operated 2y. No problems till now.There is sometimes abnormal lost of Internet connection, detected by LAN devices. I found it 3 days ago. This dysfunction is occasional 2-5 per day in occasional time.Nothing was changed/upgraded/updated in my WAN cable router or LAN or in the Cisco router. Nothing was changed on computers site (OS,LAN cards, drivers, ...). Just the problem is discovered on the router side.LAN operatation is correct, no problems was founded. Just the devices on LAN lose the internet connection (Win7, Lnx, Mac).
This is status of my WAN - does not matter if the internet connection was lost or not. It is still same:
STATUS-WAN/Gateway
Interface: UP
IP Address is assigned (checked by provider - correct)
Default Gateway and DNSs are assigned too(checked by provider- correct)
What was checked by me:
1. A. I disconnected the cable router from Cable modem
B. I connected the Cable router directly to laptop. Internet connection was right.
2. I called to my Cable provider to check my connection:
- with direct laptop connection to Cable router - Right
- with Cisco router connected to Cable router - Right, but no Internet connection on LAN side behind the Cisco router
3. Standard procedure was tested:
- Unplugged (electricity & cabling) all devices - Cable modem, Cisco router as well.
- Restart of Cable modem, +30 sec. connection of IP cable to Cisco router, start of Cisco router Still same. No Internet connection.
- SETUP/SUMMARY/Network Settings Status - DHCP Release or DHCP Renew was tryed - Still same.After several minutes - was Internet connection Renewed. Just by itself. how?
View 1 Replies
View Related
Apr 27, 2013
We have been having a very abnormal speed issue. This one has me stumped. I am fed up and thinking maybe its an Att issue that will NEVER be resolved.Brother comes and bothers me Zach internet is slow thinking hes just being picky I tell him to reboot his computer. He says its still slow. I run a speed test from my desktop computer I get a 5.36Mbps download and .63 up. I go to his windows xp professional laptop and run a speed test he pulls .63mbps down and .32 up. This is a Dell Latitude D610 with built in wifi. My desktop just so happens to be a wired connectionI grab my laptop which happens to be the exact same model and experience the same result. So I power cycle to modem, then the Linksys ea2700 router. The speeds go back to 5.37m down and normal speed up. Then after 20 minutes its back to a CRAWL.
OK the router MUST be dead. I will kill two birds with one stone. I plug in my Modem/Router combo 2wire 2700. Speed does the same thing starts off fast then slow to a crawl. Figuring it's a laptop issue I use a Linksys wireless USB adapter AE-2500. I get the same result fast then slow. NOW the crazy thing is that its only on my wireless connections. The wireless computers use wireless G and say 54mbps so why would the internet be slow only on the wireless connection.So maybe it's an interference issue So I start up the generator and plug my modem router and laptop into it. I then shut off THE ENTIRE POWER service to my house! I get the same result fast then slow. My neighbors are far apart and I have switched wireless channels and even used the 5ghz frequency with the same results.An ATT Tech says the line is fine. They came to the house and tested everything. The only thing that has happened recently was a storm which left flooding in some parts of town. Only one time was I able to test my WIRED computer and get a download speed of .04Mbps down and .32 up
View 2 Replies
View Related
Mar 27, 2013
I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies
View Related
Feb 11, 2007
The "Wireless Network Monitor" for my Linksys Dual-Band Wireless A+G Notebook Adapter Model No WPC55AG has been unable to run after I last updated my Windows XP machine using Windows Update. The problem presents itself immediately upon login (because the monitor is set to run on startup) with an error window that says "Abnormal program termination" and "WPC55AGV2.exe" in the title bar. I suspect the problem occurred because one of the new updates included an upgrade to the Microsoft .NET Framework Services 3.0.
View 6 Replies
View Related
Sep 9, 2011
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies
View Related
Jun 30, 2011
I have a network with a 2003 windows server and around 60 XP computers. I also have 2 different gateways. I am trying to access a webpage "eparts.rmpparts.com". When I enter the address it comes up to the page that says "IE cannot display the webpage".I have treid and both gateways and same result. I am also not able to ping the address from the PC within my LAN.I then went to a different network "not within my LAN" and I am able to access the site without any problem. I have accessed it from my phone also without any problems.I have tried to get to this page from the server and also around 5 other computers within the LAN and the same problem each time.I have security settings very low and also the firewalls are off. I tried on a computer that is connected to my LAN with no luck. I then disconnected that same computer and connected it to a different modem not within the LAN and had no prob getting to the site with the same PC.So I know it must have something to do with my LAN but I have no idea what it could be. I have tried everything I can think of and same result each time.
View 19 Replies
View Related
Jul 11, 2012
IE9 can't display any webpages. Troubleshooting shows that it can't detect my proxy settings. However, I don't have proxy settings/server checked anywhere. Moreover, Pale Moon is able to connect to the internet.I've tried these so far with no luck:
1. Resetting IE
2. Reinstalling IE
3. Removing idstore to see if it'd work -- nope
4. going to cmd and using dnsflush, ipv4/6 reset, winsock reset, ipconfig release
5. Reinstalling adapter
6. Removing firewalls
7. SFC scanner
Windows IP Configuration
Host Name . . . . . . . . . . . . : GLaDOS
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[Code]...
View 5 Replies
View Related
Sep 13, 2012
the guy who set the key for WPA-PSK and another one for WEP left... Anyway we can figure out what the key was?
View 5 Replies
View Related
Jul 19, 2011
We have two ASA's 5540, running IOS 8.2(4). Is there a command to find out the password that we setup for VPN Load balancing? I recall there was a command that you type under CLI and it will display all passwords.
View 3 Replies
View Related
Dec 3, 2011
I can not connect to the internet, even though it says that Im connected. What happens is when I boot up I will get internet access for about 2-3 minutes or enough togo to about a couple web pages and then connectivity will drop and I'll get the yellow triangle with an exclamation point on my network icon. The error traingle will go away after a few minutesand say I have connection again but when I go to a site I'll get "Can not display page" error. Things Ive tried was restarting the modem and router(it cant be a problem with either of them because I have another computer hooked up to the router and I have internet access on my other computer). Ive tried resetting winsock and renewed ip, no luck. Ive tried reinstalling Windows 7 64bit then also 32 bit. Thought maybe it could be a problem with the 64 bit. Ive gotten rid of my Nortons(read that could be a problem) so I uninstalled it. Ive tried unchecking Ipv6(or whatever it is) didnt work. I looked for Bonjour file in my services, didnt have it. I even bought a new NIC and my computer recognizes it but it doesnt work either. Drivers are all up to date, so says my computer when I tried to update them.
View 1 Replies
View Related
Jul 12, 2011
I recently deleted Speed Bit Video Accelerator manualy, because it couldn't uninstall itself. After deleting it, Windows 7 wouldn't display web pages in either Firefox or Internet Explorer. I'm currently posting this message in my old Windows Vista laptop, so it's not my internet connection
View 11 Replies
View Related
Jan 21, 2010
I have an ASA5510 that I am trying to set up for remote access using SSL VPN & clientless SSL VPN. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. I have a TAC case opened and have spoken with 4 engineers thus far. I have tried several software versions on the device and they all give the same result.When going to https://(outside interface ip address), I receive the expected ssl certificate error, then I click to continue to the website, and the browser never loads a page. I can see the ssl negotiation in my debug, and it completes that portion. My http debug shows the get requests to https://(outside interface ip address)/+CSCOE+/index.html and/or logon.html, but the page never loads.
View 7 Replies
View Related
Feb 28, 2013
I have a 1240Ag. Earlier I loaded a startup config from a backup. The AP came back up - I can SSH into it, but when I try to access the web management page it says "IE cannot load the webpage".
View 3 Replies
View Related
Aug 23, 2011
I installed LMS 4.0 succesfully, but when i go to topology, can view all network, but the "AswitchA" Core 4507R+E be displayed as "?"
And it can not display this "AswitchA" into CISCO VIEW, display this messaje :
"Cannot find applicable device package for ... This error could be due to one of the following:
- The device package for this device type is not installed.
- Device support for this device type is not available.
- You are trying to open a component inside a device.
To correct the problem, either install a device package for the device type, or open the parent device to manage the component."
View 2 Replies
View Related
Aug 6, 2012
we use LMS 4.2.1 and we noticed a strange behaviour when starting a discovery. From aprox. 160 devices some devices are displayed as IP Address instead of hostname. Every device is DNS resolvable and has a value for "hostname". I´ve tried every possible option in the global discovery settings but some devices have the IP instead of their hostname. how to fix this?
View 7 Replies
View Related
Sep 12, 2012
I have done this in the past but I cannot find it anywhere......how do you display the uptime of a CSM module in a 6500? The chassis has an uptime of over 2 years, but I believe the CSM module was power cycled at some point within that 2 years and I need to find out if we may be running in to the bug that occurs after 828days of uptime. We are running 4.2(6) on the CSM and 12.2(18)SXF1 IOS on the SUP.
View 3 Replies
View Related
Jan 21, 2011
IE cannot display website 192.168.0.1 so that I can set my password on my Dlink DIR-600 wireless router. I can however ping the website. Also, I can reach the website with my iPod Touch, yet I cannot set the password using my iPod since I cannot view the secure authentication code. I have reset the router to factory default. ipconfig command yields:Connection specific DNS suffix...domain.invalidIP Address...192.168.254.1Subnet Mask...255.255.255.0
View 7 Replies
View Related
Nov 9, 2011
I am getting the error message "internet explorer cannot display the webpage", my computer tells me i am connected to my wireless and that internet is available but it will not open any webpages, no matter which browser i try. I have disabled all firewalls and run diagnostics but it just tells me there is a problem with my router, despite the connection being perfect for other devices. My computer is relatively new and i'm sure its not a virus as i have run different anti-virus and malware softwares.
View 10 Replies
View Related
Jan 2, 2013
I have an in-law with early stages of temporal lobe dementia. She lives at home alone and is still pretty independent but among other things she is really struggling with anything to do with times and dates. Diaries and the like are increasingly hard to manage. I am wondering about a technological aid. She has a WIFI network at her home. If there was a way I could set up a MONITOR on the wall that could display say a diary or calendar that I could update and change remotely?. I'd need a PC set up there to run the display, and then connect to that over the internet and control what it shows.Either way it needs to be something I initiate and control as needed, so she doesn't have to do anything like send a remote assistance request, because she can't really manage that.
View 2 Replies
View Related
Oct 17, 2011
I am trying to find the file where I can edit what printers show when looking for network printers in Server 2008. In 2003 server is was the NTPRINT.inf, where you can edit what printers populate but in server 2008 I cannot edit this file. Can this be done in Server 2008?
View 1 Replies
View Related
Sep 2, 2011
I cannot access one particular website - one that I regularly use. I have checked with other users - they can access the site.
This has been going on now for about 2-3 weeks and evertime I try to access the site I get the following message: "Internet Explorer cannot display the webpage"
View 14 Replies
View Related
Jan 12, 2013
I'm trying to connect to 192.168.1.1 in order to set up a password. When I type it in, I receive a message, Internet Explorer Cannot Display Webpage. Why can I not connect?
View 1 Replies
View Related
Dec 10, 2011
I have a lap plug into a wired connection and it has stop working, i have ran the windows fix program which didn't work, i plugged a different lap top into the wire and that works fine!
View 5 Replies
View Related
Jan 20, 2011
My router (DIR-655) is all up and working but the only thing thats not working is a link to a picture posted on a web site. If you take the link and paste it in the web browser it displays fine, on a web site that should show the image in a forum, All I get is a white box with a X in it.
View 7 Replies
View Related
May 21, 2011
I find that one of the ethernet interface of ASA5510 always display RED light
View 3 Replies
View Related
Dec 21, 2011
I just installed a new RV 120W to replace my dlink router.The problem is i cant display the configuration site (192.168.1.1). My internet is working fine and when i go to 192.168.1.1 i can logon (with the password i set using the installation disk) but then i see the top of the config site (blue) but where the config panel should be i see `site cannot be displayed`.
View 4 Replies
View Related
Oct 24, 2011
Can LMS 4.0 display event directly on Topology Services when error occurs without accessing the other module by clicking right mouse on device? Anyway, I configured the logging command on all device but I cant see any syslogs on Event Monitor > Syslog. It dislays "No Syslogs are available" message.
View 1 Replies
View Related
Nov 11, 2011
Went to log into the web admin interface on my SG-300 today and I get this in both IE and Firefox:
I'm not able to login by typing user/password and just pressing enter. I've tried power-cycling the switch, however, since the power cycle, the font-panel system LED has been blinking green. I seem to recall, though I can't locate the reference now, that this means the switch is running with factory settings, but that cannot be right because:
1. I had previously saved a new configuration on the switch, which it should be using now.
2. It is answering on the configured non-factory IP address -- just not rendering the web admin interface successfully.
I've had this unit for approximately a month. This is not the first issue I have had with this unit (see: [URL] and I'm experiencing some strange LAN speed issues since I installed it. Do I need to RMA this thing?
View 1 Replies
View Related
Dec 27, 2012
I read somewhere that the security log could be set to display web address vs dns address. How do i adjust this?
View 1 Replies
View Related
Apr 28, 2013
I've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
View 5 Replies
View Related
Jan 15, 2012
we replaced our PIX525 firewall with an ASA 5540 firewall, and now we see some strange behavior in ASDM.ASDM does not display all the rules, but i see all all the rules in cli.
View 8 Replies
View Related
May 21, 2012
I am using CISCO ASA 5505. Client PC with Windows XP can use IE to make the VPN connection normally.However, client PC with Windows 7 cannot use IE to make the VPN connection.It just show the error of "Internet Explorer cannot display the webpage"
View 4 Replies
View Related
