We have two ASA's 5540, running IOS 8.2(4). Is there a command to find out the password that we setup for VPN Load balancing? I recall there was a command that you type under CLI and it will display all passwords.
View 3 Replieswe replaced our PIX525 firewall with an ASA 5540 firewall, and now we see some strange behavior in ASDM.ASDM does not display all the rules, but i see all all the rules in cli.
View 8 Replies View Relatedif there was a way in which i could get every username and password associated with my email, sent to my email account. I want to delete some old accounts and stuff but where ive made so many ive forgotten all the passwords and usernames ect?
View 3 Replies View RelatedFound a script on the wiki http:/[url]....I have run it with four commands:
conf t
username admin privilege 15 secret password1
exit
wr mem
exit
However the output file shows me that I have an error:
Command Issued: conf t
Enter configuration commands, one per line. End with CNTL/Z.
Command Issued: username admin privilege 15 secret password1
Line has invalid autocommand "username admin privilege 15 secret password1"
Command Issued: exit
Command Issued: wr mem
Building configuration...
[OK]
I found some sites that talked about "A" script not knowing that it is a new line and tries to send additional chare to the terminal. Obviously not specific to this script.Do I need to escape the end of line with a ' or ' for it to know that it is a new command? I have about 50 Routers and 100 Switches I need to change a password on.
Is there a way to reset the device and start all over again. The person who set this up is no longer with the companyand did not detail the information. We installed a new t1 line with new IP addresses and need to set this to connectwith our remote location. And I am not knowledgeable at all on how to configure this.
View 1 Replies View RelatedI typed such commands:Code:
View 3 Replies View RelatedAt the school I live in various sites are blocked so I need to use a proxy to access them. Is there any way that someone could steal my password or something while I use one? Also, let's say that I use a proxy in one web browser (let's say Opera) to view a blocked site, but then use a different browser (Firefox) with my normal IP, would I be able to use Firefox with no worries if I need to check something like my bank account? Basically, can you restrict them to one program so you can use personal information on one and normal browsing on the other?
View 1 Replies View Relatedcan a wireless router with keylogger get password for myspace or facebook.if someone is loged on my wireless network.like if there using a ipod or compute
View 3 Replies View RelatedI'm currently looking for a way to change all of our Laptop & Workstation (Approx 250+ machines) BIOS passwords using a remote tool if possible. The majority of laptops are Latitude and the workstations OptiPlex although most of the laptops have BitLocker activated. We also use Empirum software to push out software.
I have been looking around and into using the Dell Client Configuration Utility and also the OpenManage tool although I'm not too sure if they would work for us due to us using BitLocker.
I have a TP-Link Wireless Router (TL-WR340G) and I use it for both Wired and Wireless connection. I have two desktops that connects to the router through cables and I also have 2 notebooks that connects through WiFi.
Now, I want to know if there is any software that can generate passwords which I can assign into individual PCs that connects with Wifi. For example, Notebook #1 has the password "abcdefghij" and the Notebook #2 has the password "1234567890" and they can both connect to the WLAN.
We have one Cisco 2960 Catalyst switch.Rule Title: The administrator will ensure passwords are not viewable when displaying the configuration. Right now my user passwords are visible in plaintext. I tried #username <admin> password 7 - but everything I try there is an error I also tried #username <admin> secret but it says I can't have both a secret and password for a single account.
View 1 Replies View RelatedAm setting up Cisco 3750 for the first time via CLI
1. what is the procedure for configuring passwords on the device.
2. how can i stack 3 switches in a site .
I recently purchased a new laptop computer and since I already had a wireless router I thought that I could get on line easy but, it seems the password I had written down does not work. I called my cable co. Charter to see if they could correct it. Well Charter changed it to something only God knows. Now neither Charter nor myself can make my laptop access the web without directly plugging into the router. What good is a wireless router that no one knows the password too? How I go about changing a password that I do not know and neither does my ISP.
View 2 Replies View RelatedI just procured Cisco 3560V2- 48PS-S i would like to know how to set it up from scratch:
1. configuring passwords: enable and privilege
2. Creat Vlan , such that systems connected to the Vlan can connect to internet.
3. enable routing protocols
4. How do i use the switch as a default gateway for the systems on the vlan
5. how do i make sure the desktops connected to the switch are browsing the internet.
Currently have an ASA 5545. What I want to do is allow our support team to perform ALL show commands (up to and including show run) but not enable them to perform ANY configuration changes on the devices (not get into config t). This is to allow them to check ARP tables, routing protocol status, etc
i don't have access to the ASA at the moment and haven't been able to figure it out in IOS, i'm assuming its not too hard.
I've installed Cisco ACS 5.3. After I created several internal users (defined password and enabled password), Identiy Groups, Access Polices, Network Devices and AAA Clients (e.g. Cisco 1841) for Radius and configured my Router like this:
...
aaa authentication login VTY group radius local-case
aaa authentication enable default group radius enable
....
Now I'm able to login successful using my internal User. But if I try to use enable to enter the enable level I'll receive the message "% Error in authentication." when I use the defined enable password.
In the ACS logging I'll can see that "$enab15$" is missing. If I setup a user name "$enab15" I can login to enable level, but what have I to do, to use the custom enable passwords?
Step 1.2 - 1.5 is requiered for both (Radius and Tacacs). Then you have to switch to 2.1-2.7 for Radius or 3.1 - 3.7 for Tacacs authentication.
I'm just wondering, is it possible to find out or recover the passwords for users and pre-shared key for tunnel-group? The VPN connection was confiigured on ASA5505 before me, but no login details were left.
View 3 Replies View RelatedI've discovered that the DDNS update client in the RV042G does not support passwords that contains spaces. This is the first router I've run into that didn't like it.
View 1 Replies View RelatedI have a 2514 Router that i have tried numerous times to access the break sequence and do a pwd reset, while connected to the console port.. How ever its whopping me good..
[code]....
I want remove saved passwords in 2003 server with which XP clients login
View 1 Replies View RelatedWe've recently installed Windows Server 2003 at our small office for data storage, and have set up shared folders in the Win Server 2K3 for access from about a dozen Win XP Pro machines.Upon the first access of these shared folders from a Win XP Pro machine, we're required to enter a User Name & Password for the Win Server 2K3 machine:Is there a work-around for this? Perhaps some method in WinXP Pro to save the username/password? As it stands now, any time one of the WinXP Pro machines gets rebooted, or if the server gets rebooted, users of the Win XP Pro machines have to re-enter the username/password, and I'd like to find if there's away around having to re-enter that info.
View 5 Replies View Relatedfirst connect to configuration page is very slow
Second issue: after updating to FW 1.0.4 any web pages doesn't accept any passwords. I can not login to some sites. After reset to Factory defaults I can not configure router - password for ISP doesnt accepted and saved... so internet doesn't work. After rolling back FW all configuret and works fine
I just purchased a E4200 and I have some questions;
1. I have the hardware version 1, and I noticed the hardware version 2 has a newer version of Cisco Connect. Can I use the newer version of Cisco Connect on my E4200 V1?
2. Is there a way to hide passwords in Cisco Connect and in the browser UI for the router?
3. Is there a way to have a separate admin password and wireless password?
I also have a issue, I want the browser web UI to display in english, but it insists on changing it back to my native language from time to time.
How do I get guest passwords for wifi access on my android cell?
View 1 Replies View RelatedI have a network with a 2003 windows server and around 60 XP computers. I also have 2 different gateways. I am trying to access a webpage "eparts.rmpparts.com". When I enter the address it comes up to the page that says "IE cannot display the webpage".I have treid and both gateways and same result. I am also not able to ping the address from the PC within my LAN.I then went to a different network "not within my LAN" and I am able to access the site without any problem. I have accessed it from my phone also without any problems.I have tried to get to this page from the server and also around 5 other computers within the LAN and the same problem each time.I have security settings very low and also the firewalls are off. I tried on a computer that is connected to my LAN with no luck. I then disconnected that same computer and connected it to a different modem not within the LAN and had no prob getting to the site with the same PC.So I know it must have something to do with my LAN but I have no idea what it could be. I have tried everything I can think of and same result each time.
View 19 Replies View RelatedIE9 can't display any webpages. Troubleshooting shows that it can't detect my proxy settings. However, I don't have proxy settings/server checked anywhere. Moreover, Pale Moon is able to connect to the internet.I've tried these so far with no luck:
1. Resetting IE
2. Reinstalling IE
3. Removing idstore to see if it'd work -- nope
4. going to cmd and using dnsflush, ipv4/6 reset, winsock reset, ipconfig release
5. Reinstalling adapter
6. Removing firewalls
7. SFC scanner
Windows IP Configuration
Host Name . . . . . . . . . . . . : GLaDOS
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[Code]...
the guy who set the key for WPA-PSK and another one for WEP left... Anyway we can figure out what the key was?
View 5 Replies View RelatedI can not connect to the internet, even though it says that Im connected. What happens is when I boot up I will get internet access for about 2-3 minutes or enough togo to about a couple web pages and then connectivity will drop and I'll get the yellow triangle with an exclamation point on my network icon. The error traingle will go away after a few minutesand say I have connection again but when I go to a site I'll get "Can not display page" error. Things Ive tried was restarting the modem and router(it cant be a problem with either of them because I have another computer hooked up to the router and I have internet access on my other computer). Ive tried resetting winsock and renewed ip, no luck. Ive tried reinstalling Windows 7 64bit then also 32 bit. Thought maybe it could be a problem with the 64 bit. Ive gotten rid of my Nortons(read that could be a problem) so I uninstalled it. Ive tried unchecking Ipv6(or whatever it is) didnt work. I looked for Bonjour file in my services, didnt have it. I even bought a new NIC and my computer recognizes it but it doesnt work either. Drivers are all up to date, so says my computer when I tried to update them.
View 1 Replies View RelatedI recently deleted Speed Bit Video Accelerator manualy, because it couldn't uninstall itself. After deleting it, Windows 7 wouldn't display web pages in either Firefox or Internet Explorer. I'm currently posting this message in my old Windows Vista laptop, so it's not my internet connection
View 11 Replies View RelatedI have an ASA5510 that I am trying to set up for remote access using SSL VPN & clientless SSL VPN. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. I have a TAC case opened and have spoken with 4 engineers thus far. I have tried several software versions on the device and they all give the same result.When going to https://(outside interface ip address), I receive the expected ssl certificate error, then I click to continue to the website, and the browser never loads a page. I can see the ssl negotiation in my debug, and it completes that portion. My http debug shows the get requests to https://(outside interface ip address)/+CSCOE+/index.html and/or logon.html, but the page never loads.
View 7 Replies View RelatedI have a 1240Ag. Earlier I loaded a startup config from a backup. The AP came back up - I can SSH into it, but when I try to access the web management page it says "IE cannot load the webpage".
View 3 Replies View RelatedI installed LMS 4.0 succesfully, but when i go to topology, can view all network, but the "AswitchA" Core 4507R+E be displayed as "?"
And it can not display this "AswitchA" into CISCO VIEW, display this messaje :
"Cannot find applicable device package for ... This error could be due to one of the following:
- The device package for this device type is not installed.
- Device support for this device type is not available.
- You are trying to open a component inside a device.
To correct the problem, either install a device package for the device type, or open the parent device to manage the component."
i have been using the ITP7613 system and PA-A3-8E1 IMA.i have question.
Co1#sh int ATM1/0/0ATM1/0/0 is up, line protocol is up Hardware is IMA PA E1, address is 001b.2bf4.cec0 (bia 001b.2bf4.cec0) MTU 4470 bytes, sub MTU 4470, BW 1920000 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255
Co1#sh controller ATM1/0/0ATM1/0/0: Port adaptor specific information Hardware is E1 (1920Kbps) port adaptor Framer is PMC PM7344, SAR is LSI ATMIZER IIScrambling is Enabled Clock Source = INTERNALNational bits = 0x3Flinecode is HDB3E1 Framing Mode: pcm30 ADM formatLBO (Cablelength) is long gain43 120db Facility Alarms: No Alarm
E1 bandwidth of standard is 2048000 Kbit, is this right? But why displayed BW "1920000 Kbit" on ATM1/0/0 interface status and E1(1920K) ?I've never change the Bandwidth option.and As of Cisco IOS Software Release 12.2 (refer to Cisco Bug ID CSCdt57977 (registered customers only) ), the bandwidth displayed on ATM IMA T1 and E1 interfaces is 1536 kbpsand 1920 kbps, respectively.my ITP7613 system has using the 12.2 IOS version.