Error Saying Cannot Display Page
Dec 3, 2011
I can not connect to the internet, even though it says that Im connected. What happens is when I boot up I will get internet access for about 2-3 minutes or enough togo to about a couple web pages and then connectivity will drop and I'll get the yellow triangle with an exclamation point on my network icon. The error traingle will go away after a few minutesand say I have connection again but when I go to a site I'll get "Can not display page" error. Things Ive tried was restarting the modem and router(it cant be a problem with either of them because I have another computer hooked up to the router and I have internet access on my other computer). Ive tried resetting winsock and renewed ip, no luck. Ive tried reinstalling Windows 7 64bit then also 32 bit. Thought maybe it could be a problem with the 64 bit. Ive gotten rid of my Nortons(read that could be a problem) so I uninstalled it. Ive tried unchecking Ipv6(or whatever it is) didnt work. I looked for Bonjour file in my services, didnt have it. I even bought a new NIC and my computer recognizes it but it doesnt work either. Drivers are all up to date, so says my computer when I tried to update them.
View 1 Replies
ADVERTISEMENT
Jan 11, 2011
Internet shows connected but notebook fails to display any web pages. Diagnosis states resource samsung notebook device or resource (127.0.0.1) is not setup to accept connections on port World WIde Web service (HTTP).When I copied 127.0.0.1 into LAN connections and ran diagnosis again I got a similar message only this time the resource statement was (samsung.msn.com).
View 3 Replies
View Related
Jan 21, 2010
I have an ASA5510 that I am trying to set up for remote access using SSL VPN & clientless SSL VPN. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. I have a TAC case opened and have spoken with 4 engineers thus far. I have tried several software versions on the device and they all give the same result.When going to https://(outside interface ip address), I receive the expected ssl certificate error, then I click to continue to the website, and the browser never loads a page. I can see the ssl negotiation in my debug, and it completes that portion. My http debug shows the get requests to https://(outside interface ip address)/+CSCOE+/index.html and/or logon.html, but the page never loads.
View 7 Replies
View Related
Jun 12, 2011
I received a new hp laptop from a friend with a cisco linksys e1000 router. The first time I hooked it up it got online and worked great. I downloaded some updates for windows and restated the laptop for them to take effect and now it won't get back online for anything. I even restored the computer to the previous settings. All I get is the error message "Internet Explorer can not display the web page. I am running windows 7 ultimate.
View 3 Replies
View Related
Feb 12, 2012
We have blocked some sites in router which our user cannot access and it gets them default browser message "pages cannot be displayed". But I want to display pages like "You are trying to access unauthorized website" or something like that when they try to open such websites.
View 1 Replies
View Related
Mar 18, 2012
I have an ASA5510 that I am trying to set up for remote access using SSL VPN with the anyconnect client. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. When going to https://(outsdie interface ip address),I get nothing, the browser never loads a page. Here are the commands I have entered:
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.3046-k9.pkg 1
svc image disk0:/anyconnect-macosx-powerpc-2.5.3046-k9.pkg 2
svc image disk0:/anyconnect-macosx-i386-2.5.3046-k9.pkg 3
svc enable
tunnel-group-list enable
[code]....
View 13 Replies
View Related
Jul 27, 2012
Internet Explorer Cannot Display the Webpage ?I'm already logged into certain websites but most of the time or in fact all the time today I'm kicked off and I receive an error "Internet Explorer Cannot Display the Webpage."
View 19 Replies
View Related
Oct 5, 2011
I was using my internet on my Acer Windows 7 operating system wireless just fine on Monday. I tried to use it on Tuesday and could not connect to the internet wireless any longer. I get an error message next to my network stating ""The settings [COLOR=green ! important][COLOR=green ! important]saved[/COLOR][/COLOR] on this computer do not match the requirements of the network"I have never encotured this kind of problem before. I proceeded to call Comcast who did all kinds of trivial beginner troubleshooting such as restart the router, restart the modem turn on and off the computer.
View 3 Replies
View Related
Oct 20, 2012
I am having pentium p3 zenith make,window xp sp3 is the operating system. Belkin router N150 is being used.,I am able to get connection through this router on other p4 pc of my friend.,but when I try to connect to my pc.,belkin router set up do not display.,and diagnostic network connection ,indicate that error 12007 could not connect to HTTP,FTP etc., IE 8 and mozilla firefox are installed and both give the same error i.e. connection to internet could not be established
Quote:
Windows IP Configuration
Host Name . . . . . . . . . . . . : home-1d64a843b7
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : Yes[code].....
View 4 Replies
View Related
Oct 1, 2012
My laptop is experiencing internet problems. I cannot connect wirelessly. It says I'm connected and my strength is excellent, but when I open google chrome i get Error 105 (ERR_NAME_NOT_RESOLVED) unable to resolve the server's DNS address. I tried reloading and changing the settings as it says the issue might be also restarted the laptop numerously and still nothing happens.
View 14 Replies
View Related
Oct 2, 2012
When attempting to log into MTS windows live I get a blank page and (error on page) rather than the page with the user name and passwordboxes
View 3 Replies
View Related
Jun 20, 2011
i have a SMC8014WG-SI Router and its gateway is 192.168.0.1 but when i type it in the router doesn't appear at all , just says that the page cannot be found. i like portforwarding and need to be able to login the router to do so.
View 9 Replies
View Related
Aug 31, 2011
So basically my laptop shows its connected to my wireless but when i try to browse it wont let me?
View 3 Replies
View Related
Jan 13, 2010
I am using D-Link DIR-615, I need to ask is it possible that i change the error page "Forbidden Web Access" ? I have blocked some websites and i dont want ppl know that it is blocked by router because in D-Link default error msg it is clearly mentioned that " This page is not included in the router's Allowed Web Site List". Is it possible that i redirect error page to some other site? or change error message?
View 2 Replies
View Related
Mar 23, 2012
I tried to connect to my E1550 router admin page at 192.168.1.1 and I'm not seeing the login page. I'm getting an error. I've always been able to get to the admin page. I'm not sure what changed. I tried changing the IP# and subnet mask of my laptop and I still can't connect. I tried resetting the router to factory defaults.
View 1 Replies
View Related
Jan 8, 2013
Just upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 5 Replies
View Related
Dec 14, 2011
I want to load balance between two webservers using ACE10 working in bridging mode, but when putting the VIP in the url i'm getting page not found, tried many configurations but didn't work, here is the latest one
logging enable
logging buffered 7
access-list ALL line 8 extended permit ip any any
[Code].....
View 4 Replies
View Related
Oct 30, 2012
Is there I can customize the error page which is shown when someone visits a blocked site
View 3 Replies
View Related
May 8, 2012
I have ASA 5510 with CSC-SSM-10 .ASA 5510 IOS version- 8.4.2 and CSC-SSM-10 IOS version 6.6.1162.Web filtering is working fine with respective to my configuration.From yesterday morning, i was facing issue with the sites like gmail, webmail.After giving credentials like username and password in the web page, the page is not resonding.In troubleshooting process, i removed all the acls, class maps which will direct all the traffic towards the CSC. In this scenario all my mail service sites are opening.If we apply the these ACLs and Class-Maps, only my mail service sites only affecting.
View 1 Replies
View Related
Aug 18, 2011
I am configuring Clientless SSL VPN on ASA5505 with 8.2(2)17. After the login, default page should be "Home", but if activating "Anyconnect". it always goes to Anyconnect as a first page. If disabling "Anyconnect" using SSL VPN Customization Editor --> Portal --> Application, it always goes to the other one. Never get "Home" as a first page, can I set the first page manually?
View 3 Replies
View Related
Jul 28, 2011
i need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen
View 2 Replies
View Related
Jun 30, 2011
I have a network with a 2003 windows server and around 60 XP computers. I also have 2 different gateways. I am trying to access a webpage "eparts.rmpparts.com". When I enter the address it comes up to the page that says "IE cannot display the webpage".I have treid and both gateways and same result. I am also not able to ping the address from the PC within my LAN.I then went to a different network "not within my LAN" and I am able to access the site without any problem. I have accessed it from my phone also without any problems.I have tried to get to this page from the server and also around 5 other computers within the LAN and the same problem each time.I have security settings very low and also the firewalls are off. I tried on a computer that is connected to my LAN with no luck. I then disconnected that same computer and connected it to a different modem not within the LAN and had no prob getting to the site with the same PC.So I know it must have something to do with my LAN but I have no idea what it could be. I have tried everything I can think of and same result each time.
View 19 Replies
View Related
Jul 11, 2012
IE9 can't display any webpages. Troubleshooting shows that it can't detect my proxy settings. However, I don't have proxy settings/server checked anywhere. Moreover, Pale Moon is able to connect to the internet.I've tried these so far with no luck:
1. Resetting IE
2. Reinstalling IE
3. Removing idstore to see if it'd work -- nope
4. going to cmd and using dnsflush, ipv4/6 reset, winsock reset, ipconfig release
5. Reinstalling adapter
6. Removing firewalls
7. SFC scanner
Windows IP Configuration
Host Name . . . . . . . . . . . . : GLaDOS
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[Code]...
View 5 Replies
View Related
Jul 12, 2011
I recently deleted Speed Bit Video Accelerator manualy, because it couldn't uninstall itself. After deleting it, Windows 7 wouldn't display web pages in either Firefox or Internet Explorer. I'm currently posting this message in my old Windows Vista laptop, so it's not my internet connection
View 11 Replies
View Related
Jan 21, 2011
IE cannot display website 192.168.0.1 so that I can set my password on my Dlink DIR-600 wireless router. I can however ping the website. Also, I can reach the website with my iPod Touch, yet I cannot set the password using my iPod since I cannot view the secure authentication code. I have reset the router to factory default. ipconfig command yields:Connection specific DNS suffix...domain.invalidIP Address...192.168.254.1Subnet Mask...255.255.255.0
View 7 Replies
View Related
Nov 9, 2011
I am getting the error message "internet explorer cannot display the webpage", my computer tells me i am connected to my wireless and that internet is available but it will not open any webpages, no matter which browser i try. I have disabled all firewalls and run diagnostics but it just tells me there is a problem with my router, despite the connection being perfect for other devices. My computer is relatively new and i'm sure its not a virus as i have run different anti-virus and malware softwares.
View 10 Replies
View Related
Jan 2, 2013
I have an in-law with early stages of temporal lobe dementia. She lives at home alone and is still pretty independent but among other things she is really struggling with anything to do with times and dates. Diaries and the like are increasingly hard to manage. I am wondering about a technological aid. She has a WIFI network at her home. If there was a way I could set up a MONITOR on the wall that could display say a diary or calendar that I could update and change remotely?. I'd need a PC set up there to run the display, and then connect to that over the internet and control what it shows.Either way it needs to be something I initiate and control as needed, so she doesn't have to do anything like send a remote assistance request, because she can't really manage that.
View 2 Replies
View Related
Oct 17, 2011
I am trying to find the file where I can edit what printers show when looking for network printers in Server 2008. In 2003 server is was the NTPRINT.inf, where you can edit what printers populate but in server 2008 I cannot edit this file. Can this be done in Server 2008?
View 1 Replies
View Related
Sep 2, 2011
I cannot access one particular website - one that I regularly use. I have checked with other users - they can access the site.
This has been going on now for about 2-3 weeks and evertime I try to access the site I get the following message: "Internet Explorer cannot display the webpage"
View 14 Replies
View Related
Jan 12, 2013
I'm trying to connect to 192.168.1.1 in order to set up a password. When I type it in, I receive a message, Internet Explorer Cannot Display Webpage. Why can I not connect?
View 1 Replies
View Related
Dec 10, 2011
I have a lap plug into a wired connection and it has stop working, i have ran the windows fix program which didn't work, i plugged a different lap top into the wire and that works fine!
View 5 Replies
View Related
Jan 20, 2011
My router (DIR-655) is all up and working but the only thing thats not working is a link to a picture posted on a web site. If you take the link and paste it in the web browser it displays fine, on a web site that should show the image in a forum, All I get is a white box with a X in it.
View 7 Replies
View Related
Sep 13, 2012
the guy who set the key for WPA-PSK and another one for WEP left... Anyway we can figure out what the key was?
View 5 Replies
View Related
