i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
We have a stack setup with 2 C3750x-12s and 5 C3750x-48p switches. We have two of these stacks. One is working and responding with snmp just fine. Our second one is showing the errors in the logThe only difference i see between the two stacks right now are the sw versions.
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
after upgrading the firmware on the wireless lan controller 5.2.178.0 on my cisco 4402 wlc's and rebooted the devices, I am getting matches on the audit status between whats on the contoller and the wcs software. so i am trying to apply whats in the wcs templates created for the controller and i am getting this error.
SNMP operation to Device failed: Attempt to set conflicting attribute value
I am thinking that i need to rebooted the wlc's again because from the error it sounds like the values that i am trying to write to the controllers are already present
I have a Cisco 3750 switch stack and am performing QOS against a number of SVI vlans on per customer basis. I have 8 customers, each with a /29 public subnet and each with an SVI as a gateway within that /29 range. I then have a "routable" SVI vlan for routing upstream to the internet. [code]
The service policy attached to the interfaces above is supposed to perform policing on download and upload traffic. The service policy is attached to the Routable VLAN for download policing and the Customer VLAN for upload policing. For example, traffic entering the routable VLAN will be policed based on traffic matching an access list to the customers IP range (download). Traffic entering the customer VLAN will be policed based on traffic matching an access list from the customers IP range (upload).The command I am using to police is as follows - police 10485500 966080 exceed-action drop.The problem I am experiencing is traffic into the routable VLAN is being successfully policed down to the 10Mbps i have specified on a per customer basis (download).Traffic entering the customer VLAN is NOT being policed at all (upload).I am limited as to the use of the parent policy map I have specified on the interface, as I can only assign it in one direction (input).
I am currently running WCS 7.0.230 I have controllers that are 2500 that are running 7.4.100.60?
My problem is that when I try to add my controller that is a Cisco 5500 running the same 7.4.100.60 I am getting the error SNMP operation to Device failed: Sparse table not supported. Verify that the WCS and WLC versions are compatible and try again.
I have double checked SNMP strings, IP Addressing and everything else I can think of. It just doesn't make sense that I can add a Controller with the same image but different hardware and no the other to the WCS server.
I just tested IP SLA with tracking on a 3750 12.2(46)SE. And the configuration was simple enough and tested fine for redundant static routing: [code] Then I tried to do the same on a 3560 switch running 12.2(55)SE3. ip sla went in fine. But when I went to put in the track I was presented with "list boolean and" (for example) after the track and the identifier.I tossed in the ip sla "10" as the object. But shopw track shows the boolean AND as down. I don't get why the track feature is different in two switches so close in IOS version. How do I get the 3560 to track the ip sla as my 3750 does?
I've set up a USB drive to be shared via the router (tried both a fat32 and an NTFS drive). When I login from a windows machine I can use the share point without any problems. When I try to use it from a Mac (mounted via smb://192.168.1.1/sharepoint) I can access the folders and download files. I can even create folders. When I try to copy a file onto the share point (normal file name, small file size) I get an error saying "The operation cannot be completed because you do not have sufficient privileges for some of the items." The console log says: "7/3/09 1:01:06 AM kernel smbfs_composeacl: smbfs_setattr 13, ignored "
If I try to copy the file directly via a terminal window I see this:
I have a 3750 cluster and I want to know what are the recommended snmp traps to be sent. We definitely want to know when one of the switches in the cluster fails.
I've read about snmp-server enable traps stackwise and snmp-server enable traps cluster. What do these traps actually do?
I am building a few 3750 stacks, I want to be able to poll/monitor each individual switch in the stack but as it only has 1 ip associated with the stack how can I do this. I am polling the uplink interfaces but as I only have uplinks on the top and bottom switch I am blind to a switch going down in the middle of the stack.
I want to make my switch send trap when failed SSH login is detected. I found the "login Enhancement" feature and enabled the trap and logging for the failed attempt.
3750# sh run | in login aaa authentication login default local login delay 1
We are currently monitoring approximately 50 locations each having one or more cisco devices, Catalyst 3750 and 3560.Locations are connected via CWDM.We would like to monitor interface errors, signal loss and power on CWDM SFP transceivers on Catalyst 3560 and Catalyst 3750 switches. We tried to get these values (as shown using „sh interface transceiver“ command) using SNMP but we didn't get any SNMP result. What MIB or other functions/ modules/ features need to be used/activated on switch?Do we need any additional piece of hardware?
Is there anyway to pull the usernames and passwords from a switch via SNMP or write a new username and password to switch via SNMP. I have switch that was apparently misconfigured and i am not feeling like driving all the way down there to console in.
I have a snmp trap sent every 30 seconds from one of my cisco switches (a stack of 3750 to be precise): ccStatusMemberStatusChange. Do you know what it is and why it is sent continuously?
I am having a lab switch. Recently I am getting "%SCHED-3-SEMLOCKED: SNMP ENGINE attempted to lock a semaphore, already locked by itself" message and the switch has started to hang a little bit. I just want to know what this log means and how to trouble shoot.
I have this small network comprising of around 40 users complaining about the poor speed. And they have 2900 WAN router having 10M service. The interesting thing is that they are using proxy server for all the communication.I am very new to the server side of thing-and wanted to confirm if the proxy server is packed full to its capacity for serving to clients' requests making it slow or its something to do on the network like WAN link being overloaded or showing errors.I did "sh interface g0/1" (WAN interface) and to me it looks there is not much load as the tx and rxload values are fairly ok. (as shown below). Moreover the output drops is 7341. I am still guessing if thats not too bad??
The other thing I did was to test the "sh ip nat transalations" which is all coming from the PRoxy server and was wondering if that is the place of bottleneck. Currently there were showing around 570 entries. Below are the output from there as well. Also, I was keen to know what is the "----" indicates in some of th output? [code]
I am not sure whether this is the right category to which I should submit my question, but I couldn't find a section for "other software support" or anything like that.I am running Windows SBS 2003 at one of my clients and we are using Syncback as the backup software to backup important files and folders that gets written to the server on a daily basis.Now we are using two external drives for this purpose, alternating the two every second day, for improved security.However...I have set up the backup profiles exaclty with the same configurations and everything...everything is identical. But the backup to one of my drives does not want to perform giving the error : "the folder on the destination drive does not exist and can't be created"The folder does exist though, and what puzzles me is that running the backup manually or even copying files manually from the same server backup folders to the drive works perfectly, but when running the scheduled backup, it fails...and yes, the logon and authentication is set to "run as administrator" and the username and password is entered correctly.Like I said, the configs of the two drives are exactly the same, and the backup to the other drive works perfectly.I am using the Syncback free version, and support for the free version on the 2Brightsparks website is unavailable
We're since long having a problem with a DSL internet connection. The connection goes down periodically, for short times, and when performing speed tests, the connection speed varies and is usually lower (0.7 Mbit/s) than what the ISP promises (1.5-2 Mbit/s). Moreover, what modem is being used seems to have an effect.Now, I want to trouble-shoot this and get some hard facts on the behaviour of the connection. I would like to do repeated speed tests over say 24 h or so. They should be done every 3 min or so (to catch short glitches).
My question is: what software tool can I use for this? I have been searching the internet for hours, downloading a handful of applications, without finding anything that I could use. There are loads of applications that log and graph the current upload and download speeds, but that's something else - I need a tool that downloads/uploads files from/to a server, in intervals specified by me (3 min), logging the result and presenting it graphically.
ip wccp 0 redirect-list wccp_acl group-list 10 password 0 ourpassword
Received this error:
MDT: %COMMON_FIB-3-FIBIDBINCONS2: An internal software error occurred. WCCP:0 linked to wrong idb Loopback0 (xyz node name)
When the following was issued 10 minutes later:
ip wccp 70 redirect-list wccp_acl group-list 10 password 0 ourpassword
No error msg (but now wccp was active)WCCP appears to be working but we are ** having problems connecting ** with our websense (7.6) box via GRE.Websense is connected to the 6509 which is connected this 3750 switch.
I'm going to be moving into a place in the next couple months where I'll have to go wireless on my desktop (until now I've just done Ethernet so I don't even have a wifi card on my desktop). The router/modem aren't anywhere near my bedroom so my gear will be going wireless from now on All my devices are built-in wifi ready but not my desktop.
I would like recommendations as to a rock-solid, reliable, fast and well performing card as I can to make up for no hardwired connection. Especially with BF3 coming out I'm not all that thrilled with being forced into this situation but you gotta do what you gotta do. Anyhow, I'll be bringing my router (Netgear WNDR3700) so I'll have the range and speed from there about as good as I can get, so I'd like a card of equal merit.
One side note...probably not really feasible considering I want speed and performance as a priority, but I would love a card (if possible) without bullshit antennas sticking out of the case, or with external antennas you have to set up on your desk. I will go that route if I have to but man that is an aesthetic nightmare, IMO. The ones that stick out of the back of the case are the worst looking for me just as a caveat.
I have cisco switch model WS-C3750G-12S-D. It is in transparent mode. I am getting below error message when tried to create new vlan.
Proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
After deleting few unnecessary vlans, it allowed me to create.
3750#sh vtp statusVTP Version : running VTP1 (VTP2 capable)Configuration Revision : 0Maximum VLANs supported locally : 1005Number of existing VLANs : 959VTP Operating Mode : TransparentVTP Domain Name : VTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest : 0xBC 0xA7 0xEC 0xDE 0x36 0x6C 0x61 0xB4 Configuration last modified by 97.193.17.172 at 0-0-00 00:00:00
I confused with terms 'maximum supported vlans' and 'maximum locally supported vlans'. If switch is supporting vlans 1-4094 means it should also allow to create locally. Otherwise how they will pass through the switch trunks without local creation.
I am really stuck in enabling ip routing though a simple task. I have configured 10 v LAN's in stacked 3750 switches have ip base image. I want to enable ip routing for inter V LAN communication but it is giving this error:
%COMMON_FIB-4-ISSUENCODEWRONGLEN: Message IPv6 global features, rev B for slots 2 (0x4) is wrong length (10, should be 7).
We are using Catalyst 3750 with 12.2(44)SE. We have two stack configured, one with IP routing enabled. When we try to run an Acquisition Action on IP routing enabled stack, from Admin> Collection Settings> User Tracking, the system replies with an error "Failed to start acquisition: Device unreachable. Please enter a valid device". Acquisition starts successfully when we try with the other stack. We are going to investigate!
I'm having some problems when upgrading the IOS of my Catalyst 3750 switch through a tftp server. I've been surfing the net and found that there seems to be a problem when the image file is larger than 16M but this is not my case.I erased the flash to be sure that there was enough memory space to upload the image but didnt work.I also tried with archive download-sw /overwrite command and using a ftp server but the problem is the always the same: [code]To make sure it was not a problem of my computer or tftp server, I tried with a different computer and with a different tftp server but the same happen. I also tried with a 3750V2 and still the same. Even when trying to backup the current IOS to my computer, I got "error writing".
Then, I have tried to do the same with a different model of switch, a WS-C3560-48PS and it works perfect.I still need to try using Xmodem but Xmodem takes ages to finalize the process.
Have a small stack of two 3750 routers. Get the following error message every few secounds:
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state UP
Now I replaced the stacking cables but no joy. It was ok for an hr or so but then the error messages popped up again. Also random links on this stack back to access layer user switches have been going up and down randomly. So I have decided to take the next step and upgrade the IOS.
Although when I try and copy a new IOS I get the following error:
%Error writing flash:/c3750-ipservicesk9-mz.122-55.SE6.bin (No space left on device)
Seems this image is 130MB while the image that is currently on it is 74MB and free space is 54MB. How do I get the image onto the router? If I delete the current image from flash will that cause the router to stop functioning?
Also I noticed there seems to be more than one flash directory. See below:
copy tftp: ? flash1: Copy to flash1: file system flash2: Copy to flash2: file system flash: Copy to flash: file system null: Copy to null: file system nvram: Copy to nvram: file system running-config Update (merge with) current system configuration startup-config Copy to startup configuration system: Copy to system: file system vb: Copy to vb: file system
The current router image seems to be in flash1 and flash 2 also. Could I delete the image from flash1. Upload it there and then boot the router from flash1?
power supply problem...?Switch cisco WS-C3750-24P is showing "Unavail" from sh env all.Switch3750#sh env all FAN is OK,TEMPERATURE is OK,SW PID,Serial# Status Sys Pwr PoE Pwr Watts,Does it means that power supply 1 was removed? failed?,Do you know about another command to see more details?
We have a number of 3750 stacks used as access layer switches connecting Siemens VOIP phones and then a PC that connects to the phone.
For example if I plug PC A to the phone that connects to port 13 I pick up an IP addressand all works as predicted now if I plug in PC A to any other VOIP phone that connect to another port on the same switch it goes in error disable state ITs like the switch is holding my PC mac address and locks it down with the port which in my case is Gi2/0/13.
