I get the following error:
Router#config t
Router(config)#snmp-server view rttmon ciscoRttMonMIB included
%Bad OID
The same command is accepted on a Cisco 2900 router
Router#show version
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
[Code]......
I have been experiencing wireless connectivity issues with one of our Cisco 1231G AP. Every now and then users would not be able to connect to the AP. To dive deeper into this issue, I would like to configure SNMP traps on this AP. We are using PRTG and there is an option to configure SNMP trap. However, I would need to now the OID of the AP. Also i need to check for interface up/down status for both fastethernet and the radio. PRTG should be able to notify me when there is any interface resets.
View 6 Replies View RelatedI getting continuously BGP notification error.We are using the cisco 1941 router. i have attached error and configuration.
View 1 Replies View RelatedCan you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
I am using LMS 4.0 and I keep encountering this issue "Error performing SNMP Operation"
View 5 Replies View RelatedI have a cat 3750 switch with the folowing snmp v3 config:
-snmp-server group admin v3 priv
-snmp-server user lmsadmin admin v3 auth md5 password1 priv aes 256 password2
The credentials on the device in LMS are as folowing:
where Auth. password = password1 and private password = password2:
When I run a credentials verification job, I get the following error message:
Error performing SNMP operation.
I have tried this on LMS version 4.0 and 4.1 with the same result.
i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
View 9 Replies View RelatedWe have a stack setup with 2 C3750x-12s and 5 C3750x-48p switches. We have two of these stacks. One is working and responding with snmp just fine. Our second one is showing the errors in the logThe only difference i see between the two stacks right now are the sw versions.
View 1 Replies View RelatedI am trying to configure Crypto PKI in ciscio 2911, Once i configured the root certificate for the router , i can see the validity date wrongly but the same certificate is fine in the other devices . [code]e when i am trying to configure the local certificate.
View 1 Replies View RelatedIf all you have is a high end cisco router available, can you plug in hosts to the router ports, and configure them within the same subnet? (When I try to configure ports within the same subnet, I receive a "same subnet" error.
View 3 Replies View RelatedI have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies View RelatedFirmware 1.3 introduced a DHCP server.
It seems that I can add a pool for any subnet except the 192.168.1.1/24. I have successfully added a pool for 192.168.0.1/24, 172.16.16.1/24, etc. But when I use the same commands to add a 192.168.1.1/24 pool, I get:
sw(config)#ip dhcp pool network Device sw(config-dhcp)#address low 192.168.1.20 high 192.168.1.250 255.255.255.0 Illegal IP addresses range or subnet configuration Trying to configure a network pool on default IP interface
VLAN 1 IP was changed from default 192.168.1.254 to a static of 192.168.0.1.
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies View Relatedi'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies View RelatedI have a Cisco 1941 which has several Cisco VPN clients connecting to it which all works fine. The details of the LAN and VPN clients are as below:
Cisco 1941 LAN : 172.16.1.0 255.255.255.0
VPN Clients : 192.168.5.0 255.255.255.0
As mentioned this works fine but I'm about to setup a point to point VPN with from the above Cisco to another site which isn't controlled by myself and the remote side of this point to point VPN will only allow connections from the "172.16.1.0" subnet to communicate with it.
The issue I have is that the Cisco VPN clients also need to communicate with the remote side of this point to point VPN but they are obviously coming from the "192.168.5.0" subnet. Is this possible and where to start with this that would be fantastic.
I got 2 DC Cisco MWR 1941 and 3600, I do not know the reason why when I set up IP NAT to 1941 does not work but if I do it in the 3600 if it works.
View 13 Replies View RelatedI have a problem with my routers (cisco 1941)I'm running a DMVPN network (Hub and spoke)All the hubs are connected to the 2 hubs. With 4 tunnels. (each hub has 2 interfaces to the spokes. the spokes only have one interface to the hubs, so I splitted them and so I now have 4 dmvpn tunnels). one of the interfaces on a hub malfuntioned and because of that the customers had problems with logging in and sending packets. I made this kind of structure because of when one of the tunnels failed the spoke could use the 3 others... BUT, what happened here was that the spoke still tried to use all 4 of the tunnels and because of that I had 25% package loss!So this didn't work. Now I read about IP SLA, but I was wondering of this could work? (I cannot test it on spare routers, and I don't want to implement it and risking a total network failure...) and how to configure it. Should I make 4 different sla processes which I should all 4 track? And when I make the ip routes, how should I make or configure it so that 1 of the tunnels/interfaces fails that the spoke would addapt the routes?
View 1 Replies View RelatedI'm trying to get two Cisco 1941 routers with HWIC-1T and HWIC-3G-HSPA interfaces to use the 3G interfaces if the frame is down (as it is right now).In the lab, I was not able to get these to use the 3G interfaces as a backup (i.e. backup interface cell 0/1/0) and I've not been able to workout the correct incantation for static routing either.
kununurra#show ip int br d1
Interface IP-Address OK? Method Status Protocol
Dialer1 172.31.2.94 YES IPCP up up
[Code]....
I have been breaking my head over a problem with my new 1941W ISR since about two weeks now.When I restart the router, the service-module wlan-ap0 is not working.After a restart of the router, when I ask a service-module wlan-ap2 status, I get:Service Module is Cisco wlan-ap0Service Module supports session via TTY line 67Service Module is waiting for registration messageService Module reset on error is disabledService Module heartbeat-reset is enabledService Module is in fail openService Module status is not available
After a while it changes to Service Module is failed.If I restart the module with service-module wlan-ap2 reset, it works. Is this a technical error?
We bought a CISCO1941 K9 router. To enabled IPSec feature, I need the PAK to active IPSec on 1941. Where I can buy a valid PAK? Could it be done via on-line support?
View 5 Replies View RelatedI have got a Cisco 1941 router and would like to activate my SSL VPN license on it. How do i go about it?
View 6 Replies View RelatedWhat is the processor available in cisco 1941 router? is it RISC?
View 4 Replies View RelatedHow do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies View RelatedOn our Cisco 1941, we have 2 gigabit ethernet ports and a 4 port fast ethernet switch EHWIC card configured as follows:
GigabitEthernet0/0 131.x.x.81 255.255.255.248 - internal
GigabitEthernet0/1 131.y.y.234 255.255.255.252 - WAN
Vlan2 192.168.0.249 255.255.255.0 - LAN2, NAT inside
[Code]....
I have tested using some UDP packet sending/receiving software (which works through another router), and the packets just aren't getting through. Likewise trying to telnet into the external IP on port 80 doesn't get through to the destination server.
It feels like the route doesn't exist between the Vlan 100 and Vlan 2 when it's coming in, or maybe there's an ACL needed for the incoming traffic?
We have a Cisco 1941 Router with two single HWIC cards supporting two T1 lines 3Mbps total bandwidth. We have a distance learning lab that takes atleast 2mb connection when in use so it realy kills our bandwidth. I was looking to possible add a thrid T1.
My question: Can I just buy a double wide HWIC card and replace the single port one. Would this require re-configuration or it's simply plug n play?
What other options can I try for more bandwidth instead of adding thrid T1.
I've got some 1941 ciscos set on every branch.We have native L2 between this offices and I want to use external ip addresses on gig 0� interfaces anfdf local ip addresses on lo 0 interfaces, and use lo 0 for vpn connections.
I do:
int gig 0/0
ip add 192.168.181.14 255.255.255.0
ip nat outside
I can ping it from local network behind giga 0/1 but i can't ping it fro outside, how can i do this?
I have recently gotten a cisco 1941 router running version 15.1(3)T, and am trying to configure the router as a PPPoE server for access via a vlan on one of the gigabit ethernet ports.I currently have a cisco 2620 router (version 11.3(2)XA4) with the following relevant configurations:
vpdn enable
vpdn multihop
vpdn domain-delimiter @ suffix
!
vpdn-group pppoe
[code]....
I am trying to duplicate this (all but IP addresses) on the new router, but there are some options that do not seem to exist in this particular software/hardware combination. Specifically,
vpdn-group pppoe
accept-dialin
protocol pppoe
does not accept "pppoe" as a protocol, only allowing l2tp. What has changed, and what the proper configuration is.
We purchased this router with the cisco IOS software installed. I've installed the Vista driver on my win 7 box. I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.
View 3 Replies View RelatedI currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
I have a site to site vpn between a Cisco 1941 Router and a Watch guard XTM22 Router. The tunnel is up, and from the side with the Watch guard Router, I have full access to the LAN on the Cisco 1941 side.
However, I cannot access any of the devices on the LAN on the Watch guard side. If you had to guess, which router would you say is causing the problem? I really don't know where to start looking.
I was wondering about the folling witch i found in a Cisco 1941 running config
View 2 Replies View RelatedMy ISP is going to provide internet with dual path , for auto changover he (isp it admin) is planing for bgp implimentation.
is 1941 is supportable for bgp protocol ? Is it possible to create bandwitdh rate limit based on ip address on access list (be cause we are getting some 10 Ip address from isp , out of 10 ip address , 3 ip addres has to go 3 diffrent departments) , i want restrict theese 3 ip address with 1 mb traffic as 1:1.