Cisco WAN :: What Is The Processor Available In 1941 Router
Jan 31, 2012What is the processor available in cisco 1941 router? is it RISC?
View 4 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 7600 Load On Router Processor From Ip Policy
Jul 29, 2012today i installed new router 7600 , but im facing some thing the cpu is increasing and it reached 50 % and still increasing as the bw dissipated is increasing .im applying ip policy which set next hop for many internet source my question is , how to know the cu percentage which is used by this ip policy , also , how to know the percentage by access-list ??
View 4 Replies View RelatedCisco Routers :: What CPU / Processor Is Used By SRP 500 Series
Nov 24, 2011I'm just courious as to the platform specs of the SRP500 series routers. What processor is used, how fast is it and how much RAM and flash do they have?
View 4 Replies View RelatedCisco WAN :: 6500 Processor Memory And BGP / RIB Table
Jan 23, 2013We have a couple of 6500 series switches and have 3 BGP peerings to each. The 6500 series switches are loaded with WS-SUP720-3B Supervisor Engine. I believe there is a limit to the number of IPv4 routes WS-SUP720-3B supports(256,000). We also have "soft-reconfiguration inbound" configured on the BGP peerings. Thus when I do a "show ip bgp A.B.C.D" it displays three routes from 3 BGP peers and it displays an additional 3 "received-only routes" which I think is due to the "soft-reconfiguration inbound" configuration. We currently filter inbound routes from the BGP peers to be between /0 and /27
We are now looking to add another 2 BGP peerings. I am not too sure if the WS-SUP720-3B will be able to handle all the BGP routes. Is this limit of 256,000 IPv4 routes due to Processor memory limitation or is it software related? Would removing the "soft-reconfiguration inbound" save me some memory ?
Cisco WAN :: 3845 Processor High Utilization
Apr 22, 2011My client using 3845 as a core router . 200 number of branch are connected through 6 ISP.Some of days average process shows 90 % . Max time 50 %.In the morning when Branch location are off then time also high utilization.High utilization is not continue after intervals of time or periodic time its goes to high.
have any solution for that ?. before once 3845 is crash for that. another is ready for replacee.We test another device like core switches for observation CPU rate.
Intel I5 Processor Download Lan Driver?
Mar 15, 2012windows server 2003 drivers
View 1 Replies View RelatedDual Processor Motherboard For Server?
May 31, 2011Dual processor motherboard for server?
View 1 Replies View RelatedWhat Is Neg1 And Neg2 Processor In 7600 Series Cisco
May 28, 2011what is neg1 and neg2 processor in 7600 series cisco.
View 1 Replies View RelatedCisco WAN :: 2911 Have Aggregate 1.6 Gbps Towards Route Processor
Aug 11, 2011The Cisco 2911's have aggregate 1.6 Gbps towards route processor - I am trying the same specs for Cisco 3845 router? from url...The EHWIC slot provides enhancements to the prior generation's high-speed WAN interface card (HWIC) slots while provide maximum investment protection by natively supporting HWICs, WAN interface cards (WICs), voice interface cards (VICs), and voice/WAN interface cards (VWICs).
• Four integrated EHWIC slots on the Cisco 2901, 2911, 2921, and 2951 allow for more flexible configurations.
• Each HWIC slot offers high-data-throughput capability
• Up to 1.6 Gbps aggregate toward the route processor
• Up to 2 Gbps aggregate to other module slots over the MGF
Cisco WAN :: 7606 - Add Route Switch Processor 720 As Standby
Sep 15, 2012I have a 7606 Router with single Route Switch Processor 720 at the chassis works as active RP ( Route Processor ). Can I add another RP to the chassis as standby in case of failure of the first RP ?
View 28 Replies View RelatedCisco WAN :: 7600 Series SPA Interface Processor-600 Compatibility
Oct 3, 2012does the Cisco 7600 Series SPA Interface Processor-600 (7600-SIP-600-DC) only support a single SPA, e.g. 1 x SPA-OC192POS-XFP?
The 10Gbps through put on the 7600-SIP-600-DC and [URL]to show that this is the case.
Cisco Switching/Routing :: 1712 High Processor Utilization?
May 22, 2012I am running a 1712 12.4(25d) with NAT, VPN and FW/IDS. I have a broadband ethernet connection at 20mb. As I run some traffic through it, the processor jumps up to near 100% and throughput comes to a screeching halt. IP CEF is turned on and makes no difference when it is turned off or on.
View 3 Replies View RelatedCisco Infrastructure :: SRE-9XX Quad Core Upgrade Processor In Devices
Sep 23, 2012Any thoughts on Cisco putting a quad core processor in some near future version of this card?, the current versions are simple dual processors that does not give you much to work with if running ESXi 5 on one of the vCPUs.
View 1 Replies View RelatedCisco WAN :: 7600 / 6500 / ASR9K - Route Processor Information
Feb 19, 2012I am very new to high end Cisco devices.(like 7600/6500 or ASR9K).
Why do we log in on RP. What actions we can perform after logging-on RP (route processor) or Why they are required ? Cant we make those by normal router mode (router#) .
Cisco :: Does LMS 4.2 Support Intel Xeon X7560 Processor In Hyper-V Environment
Apr 8, 2013Does LMS 4.2 support Intel Xeon X7560 processor in Hyper-V environment?
View 1 Replies View RelatedCisco Switching/Routing :: 7600 High CPU Switch Processor And DFCs
Nov 16, 2011I am a little stuck trying to troubleshoot unusually high cpu on 7600 Platform.This has been going on for many hours and not been causing a problem, but this doesn't seem replicated in our network and I am concerned about the cause.I have attached some output below, and disabled netflow on interfaces to free some switching CPU. How to track the cause of this? We only have routing protocols and 5 static routes to Null 0, so I cant see how this can be a route loop, but willing to stand corrected. Routes are learned from BGP with OSPF/MPLS internally on the network. This switch also connects to access switches on RIP and EIGRP.
No change has been made to this device when this problem started to occur so I am suspecting something about the traffic has changed or there is a rougue user? [code]
Cisco Switching/Routing :: WS-C3750X-24S / Continuous High Processor Utilization Involving Hl3mm Process
Apr 3, 2012We are running a stack of 2 WS-C3750X-24S-E's with IOS version 12.2(58)SE2 and we are seeing continuous high processor utilization involving the hl3mm process. The stack is configured for PIM Sparse mode, with 2 upstream Nexus 5596'es acting as both RP candidates and as BSRs. The hl3mm process generally runs at about 19% but can spike up into the 60% range.Symptoms on the 3750X are spiking latency and sluggish CLI perfformance. I thought at first that we might be running into SDM limits, but the "show platform tcam utilization" show that we are far under the limits of the default SDM template. Performing the "show ip pim (vrf name) bsr-router" command freezes the system and takes 20-30 seconds to return results. Similiarly configured WS-C3750G-12S running 12.2(55)SE3 does not exhibit these same issues.
View 4 Replies View RelatedCisco VPN :: PAK To Activate VPN On 1941 K9 Router
Jul 1, 2012We bought a CISCO1941 K9 router. To enabled IPSec feature, I need the PAK to active IPSec on 1941. Where I can buy a valid PAK? Could it be done via on-line support?
View 5 Replies View RelatedCisco VPN :: Activating SSL On 1941 Router?
Mar 23, 2011I have got a Cisco 1941 router and would like to activate my SSL VPN license on it. How do i go about it?
View 6 Replies View RelatedCisco VPN :: How To Configure SSL VPN On 1941 Router
Mar 22, 2011How do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies View RelatedCisco WAN :: Cannot Log Into 1941 Router To Setup
Mar 28, 2011We purchased this router with the cisco IOS software installed. I've installed the Vista driver on my win 7 box. I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.
View 3 Replies View RelatedCisco WAN :: Adding IPSec To 1941 Router?
Jan 17, 2013I need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.
View 1 Replies View RelatedCisco WAN :: 1941 Choose Router For VPN And Eigrp
Feb 16, 2013We have software router vyatta and about 15 branches with cisco 881w and cisco 1941. All branches have 10mbs bandwidth and 3 of them have 50mbs. Link to vyatta has 100mbs bandwidth and situated in datacenter.All branches connect to vyatta via vpn site-to-site with ipsec.I want to change vyatta to cisco router or asa.
View 7 Replies View RelatedCisco WAN :: How To Break 1941 Router Password
Jun 16, 2010i have cisco 1941 router.unfortunately i dont remember password.Can any body tell me how to break password.I tried to go in Rom mon using ctr+break but nothing is happened.
View 5 Replies View RelatedCisco WAN :: 1941 Router ATM Interface Went Down While Applying QoS?
Sep 28, 2011c1900-universalk9-mz.150-1.M4.3
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*0 CISCO1941/K9 FCZ1510C50V
Technology Package License Information for Module:'c1900'
----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
[code].....
Cisco WAN :: Load Balancing In Router 1941?
Nov 28, 2012i have cisco 1941 router with HWIC-4EWS Card We have two ISP, how to configure the load balancing
View 3 Replies View RelatedCisco WAN :: 1941/K9 Router Configuration For Internet?
Dec 22, 2010We configured 1941 k9 router for inernet purpose
ip name-server 218.248.255.146ip name-server 218.248.255.212multilink bundle-name authenticated!!!license udi pid CISCO1941/K9 sn FHK144773MG!!interface GigabitEthernet0/0 ip address x.x.x.x 255.255.255.248 ip nat outside ip virtual-
[Code]....
when i configured access-list 2 permit any . Internet working on local systems but we are not able to connect telnet.
Cisco WAN :: Bundling 2 Gigabitethernet In 1941 Router
Apr 7, 2011I am using cisco 1941 router in my DC for Internet service. I am going to terminate 2 WAN links each 4 mbps to my Gigabiethernet ports. Is bundling is possible to enjoy full 8 mbps internet to my organisation?
View 5 Replies View RelatedCisco WAN :: 1941 Router - CP Express Not Working After Upgrade
Aug 13, 2011I am trying to upgrade CP Express to 2.5 and after the upgrade I bring up the webpage to login and I am prompted for my credentials, I enter them and I am authenticated. However the CP Express home page never loads. I have tried to reload 2.0 but it does the same thing.
View 3 Replies View RelatedCisco Switching/Routing :: 1941 Router Cannot Get To Internet From PC On LAN
Mar 12, 2012I am having an issue accessing the internet from a PC on the LAN. I have configured the PC with the gateway of the router infront of the ISP to test. I can ping from the router to google or any other internet IP. From the PC I can ping to the GIG0/1 (Inside LAN IP) and the GIG0/0 (Outside WAN IP going to ISP) but I can't ping the Next Hop IP of the ISP or anything past that. If I do a trace route from the PC to the google IP address it hits the GIG0/1 Inside LAN IP Address but fails from there. Here is a cut down snap shot of the router configure
[code]....
Cisco Switching/Routing :: Setting Up VPN For 1941 Router?
Sep 6, 2012im having trouble setting up a vpn for a 1941 router this is what I have setup
crypto isakmp policy 10
encr aes 256
authentication pre-share
crypto isakmp key ########## address 63.247.48.50
[code]....
my whole problem comes about when i need to Nat 192.168.1.0 to 10.12.14.0/24 before it goes through the tunnel.
Cisco WAN :: Configure 1941 Router For PPPOE With Dynamic IP?
Dec 18, 2010how to configure the Cisco 1941 router for PPPOE with dynamic IP
View 10 Replies View RelatedCisco WAN :: 1941 - Speed Slow After Connecting To Router
Apr 6, 2013In my company bought 20 mbps lease line(ISP Line).I connect directly with my laptop and after checking it show 20 mpbs speed.If i connect cisco 1941 router and configure PAT and Its working fine but I check with speed I connect directly to another interface on my router to laptop at that it show only 8 mpbs speed.I am check with ISP person but they told its not an issue in ISP because we connect directly it show perfectly 20 mbps speed but connecting with your router at that time it show 8 mbps speed,so problem with your router configuration.
View 4 Replies View Related