today i installed new router 7600 , but im facing some thing the cpu is increasing and it reached 50 % and still increasing as the bw dissipated is increasing .im applying ip policy which set next hop for many internet source my question is , how to know the cu percentage which is used by this ip policy , also , how to know the percentage by access-list ??
View 4 RepliesI am a little stuck trying to troubleshoot unusually high cpu on 7600 Platform.This has been going on for many hours and not been causing a problem, but this doesn't seem replicated in our network and I am concerned about the cause.I have attached some output below, and disabled netflow on interfaces to free some switching CPU. How to track the cause of this? We only have routing protocols and 5 static routes to Null 0, so I cant see how this can be a route loop, but willing to stand corrected. Routes are learned from BGP with OSPF/MPLS internally on the network. This switch also connects to access switches on RIP and EIGRP.
No change has been made to this device when this problem started to occur so I am suspecting something about the traffic has changed or there is a rougue user? [code]
When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies View Relatedwhat is neg1 and neg2 processor in 7600 series cisco.
View 1 Replies View Relateddoes the Cisco 7600 Series SPA Interface Processor-600 (7600-SIP-600-DC) only support a single SPA, e.g. 1 x SPA-OC192POS-XFP?
The 10Gbps through put on the 7600-SIP-600-DC and [URL]to show that this is the case.
I am very new to high end Cisco devices.(like 7600/6500 or ASR9K).
Why do we log in on RP. What actions we can perform after logging-on RP (route processor) or Why they are required ? Cant we make those by normal router mode (router#) .
how can I clear the counters of the policy-map statistics in an 7600 and the 1841 router?
View 6 Replies View RelatedI am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
I want to ask about cisco 7600 model is it a switch or router or layer3 switch or Multilayer switch ?
here is the sh version :
===================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team
[code]....
I am running a 1712 12.4(25d) with NAT, VPN and FW/IDS. I have a broadband ethernet connection at 20mb. As I run some traffic through it, the processor jumps up to near 100% and throughput comes to a screeching halt. IP CEF is turned on and makes no difference when it is turned off or on.
View 3 Replies View Relatedwe are using 7609 router. it forwarding traffic to wards my firewall which was not allowd in my router. when ever im checking for routes in router using show ip route x.x.x.x its showing SUBNET IS NOT IN TABLE, but in workmy firewall dropped connection i can able to see that networks.
View 2 Replies View RelatedWe are running a stack of 2 WS-C3750X-24S-E's with IOS version 12.2(58)SE2 and we are seeing continuous high processor utilization involving the hl3mm process. The stack is configured for PIM Sparse mode, with 2 upstream Nexus 5596'es acting as both RP candidates and as BSRs. The hl3mm process generally runs at about 19% but can spike up into the 60% range.Symptoms on the 3750X are spiking latency and sluggish CLI perfformance. I thought at first that we might be running into SDM limits, but the "show platform tcam utilization" show that we are far under the limits of the default SDM template. Performing the "show ip pim (vrf name) bsr-router" command freezes the system and takes 20-30 seconds to return results. Similiarly configured WS-C3750G-12S running 12.2(55)SE3 does not exhibit these same issues.
View 4 Replies View RelatedHow to activate "per-packet load sharing" on a 7606S with RSP720-3CXL engine and 7600-ES+20G3CXL module. The IOS version is : 7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRD4, RELEASE SOFTWARE (fc2)
I tried the two (2) following commands but they are not supported :-
hw-module slot1 ip load-sharing per-packet
- ip load-sharing per-packet (on interface)
i am having a problem of load balance traffic over two WAN links connecting our 2 cisco 7600 routers, as i just knew that 7600 is not supporting per packet load sharing only per destination and as per our monitoring tools that one link is underutulized the other is overutilized.
View 10 Replies View RelatedI have Cisco 7609 router and we have observed that router is rebooted due to the following error ;SLOT 3: Apr 13 16:06:26.621: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on Egress ESF Engine: Control Store Parity Error SLOT 3: Apr 13,Slot -3 we have SIP-400 card. We would like to know if there is any MIB which can monitir such reboots.
View 1 Replies View RelatedI am trying to bridge the traffic(including different vlan traffic) from rtrA to rtrB using "bridge-group" functionality.I achived the same using a 7200 using the below configuration. [code] When I tried the same using 7600 router ping failed between rtrA and rtrB. Then from the documents it seems "bridge irb" is not supported in 7600.Is there any other way we can achieve the same fuctionality ( eg: using switchport also fine) ?
View 3 Replies View Relatedi try newest ios 15.1(3)S0a and 12.2(33)SRE
in both case some times i obtain lowing traffic on interface and highest cpu - to 100%
after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s
CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
[Code].....
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies View Relatedi have cisco 7600 router , here is show run : Gateway7600#sh run Building configuration...
Current configuration : 4787 bytes
!
! Last configuration change at 09:08:04 UTC Sat Apr 20 2013 by xxxx
!
version 15.2
service timestamps debug datetime msec
[Code]....
I have Cisco 7606 and wanted to test whether Cisco can drop frames due to invalid v lan ether type . i have configured the ports as
interface GigabitEthernet5/1
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet5/2
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
I have configured port also with encapsulation trunk dot1q ether type 88a8. i injected traffic with v lan ether type 0x8100. I expected to see drop traffic , however traffic passed in port to port.
I have a 2821 Router, with a VWIC2-2MFT card in it, with two T1s going into that card. The two T1s are a bundled MPLS line.
I then have a cable modem connection going into the gigabit Ethernet GE 0/1 port on the router.
Right now, the cable modem provides a backup connection in case the T1s go down.
What I was wondering is if there was a way to 'combine' the bandwidth from the two T1s with the cable modem?
i want to to ask about redirecting in MLS 7600 .assume the user a has an ip x.x.x.xand that user requested url...i want to to redirect his request to url...the users that have to pay the monthly bills , i want to give thim an ips and redirect all the http requests from this to a special local webpage .is is applicable to to it on router cisco 7600 ??or is it applicable on router 7206 npeg2 ? also i have siwtch 2960g.i dont want to do it by proxy server.
View 4 Replies View RelatedI am a soon to be network admin and have never set up a network to an existing network. Steps you need to add a new location to a company's network. For example if they are using 8 Building with 7600 Routers and 6500 and you need another building and they are using MPLS or Private Network, or Internet.
View 4 Replies View Relatedon 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies View RelatedIs it possible to configure MST on ASR and have rapid-pvst on 7600? can they interoperate? ASR sees no BPDUs and both are root bridges.
View 2 Replies View RelatedI have a 7600 with ws-sup750 and when it boots it displays these errors:
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: [URL]
Firmware compiled 07-Apr-08 22:12 by integ Build [100]
00:00:05: %C6K_PLATFORM-0-UNKNOWN_CHASSIS: The chassis type is not known.(0x6003)
[Code]....
Then it got stuck in rommon, i tried using a 7200 pcmcia card (I downloaded the 7600 IOS there) but if i do from rommon boot disk0:
it complaints with :open: file "c7200-atafslib-m" not found so, it doesn't boot.
Anything I can do to be able to boot this device ?
i have a 7206 router to be used as a gateway for internet router 7206 inerfaces are connected directly to cisco switch 2960g note that 7600 work only at 1 gega , and cant be used for 10 or 10 . im looking forward to use router 7600 instaed of 7206 i copied the config of 7206 and pased in 7600 but some commands which are under interfaces command was not accepted here is the config which as not accepted in 7600 router
%%%%%%%%%%%%%%%%%%%%%%%%
duplex auto
speed auto
media-type rj45
negotiation auto
%%%%%%%%%%%%%%%%%%%%%%%%
note that the 4 lines above was not accpted in 7600. does these commands will affect the new config ?i just want to ask before im trying to apply this config to production network?
Actually i have 7600 router and all trafic passes through Gi0/1(Routed port) interface to 6500 series switch. I need to create a vlan on this router eg. vlan 10 Any how it is possible assign a vlan to routed port and traffic of wan interfaces and the vlan traffic passed together.
View 2 Replies View RelatedES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
I have run into a problem testing static route failovers using ECMP. I have an edge device (SUT) that has 2 NIC interfaces to an internal Loopback. Each NIC is a unique Gi port on an 7609 VLAN tagged with unique IP subnets. The 7600 is configured to route the loopback via the 2 NIC. I am using CEF in the network for other traffic performance testing. Using an external sniffer we can verify that when a ping is initiated externall to the SUT loopback a specific path is selected by the router.
Ping host ------Network-----7609 Gi1/21 (172.16.110.9)-----------SUT Nic1 (172.16.110.10)
| |
| -------Loopback 137.168.68.114/32
| |
7609 Gi2/21 (172.16.110.73)------------SUT Nic2 (172.16.110.74)
[code]....
Now, when the selected path is taken out of server (pulling cable for example), the 7609 is not clearing the routing table to indicate that particular path is down and failing over to the secondary path. Other things I have noticed is the show ip cef still shows both peers as well as the arp table but the interface shows down (show interface gi1/21 for example). I am running 15.1. My understanding is that since the ports are directly connected to the router, the ports should be detected as down and any association of the IP for the down port should removed. This should trigger the static route to update the static route for the end destination to use the second path and traffic should continue.
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)BOOTLDR: Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
how to know if my bgp neighbour advertised my network from his side or not ???
here is my config :
Gateway7600#sh ip bgp
BGP table version is 8, local router ID is 192.168.40.3
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
[code]....
I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.
View 2 Replies View RelatedCisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop" do not do the same job.
View 8 Replies View Related