Cisco Switching/Routing :: Bridging In 7600 Platform
Apr 24, 2013
I am trying to bridge the traffic(including different vlan traffic) from rtrA to rtrB using "bridge-group" functionality.I achived the same using a 7200 using the below configuration. [code] When I tried the same using 7600 router ping failed between rtrA and rtrB. Then from the documents it seems "bridge irb" is not supported in 7600.Is there any other way we can achieve the same fuctionality ( eg: using switchport also fine) ?
View 3 Replies
ADVERTISEMENT
Dec 22, 2011
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies
View Related
Feb 5, 2013
We have the following design in mind
3750 Stack (Voice gateway for phones configured on the 3750 and has a VPC nexus)
+ +
+ +
+ +
(Nexus5596) ++++++++++ (Nexus5596) (Gateway for all other vlan like PC / servers / etc)
+ +
+ +
+ +
3750x access layer (VPC to Nexus)
[CODE].....
View 1 Replies
View Related
Aug 24, 2012
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102
Autobooting specified file using Variable BOOT .....
Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
[Code].....
View 1 Replies
View Related
May 6, 2012
I got the error in object when I try to add a new HSRP group in new vlan.All the HSRP group has the same HSRP group the 2.another way to provide clients's default gateway redundancy for each Vlan intead to use the HSRP?
View 4 Replies
View Related
Mar 27, 2013
I am having problems with IGMP and QoS on CAT6500 platform with SUP720 engine.The problem is, it seems that all IGMP packets are getting marked with DSCP 48 when sent out of the switch regardless of any input service policy. I found several articles saying that PFC QoS does not apply to IGMP packets. However in IOS 15 that should be possible, but I didn't get it to work there either. [code]
View 0 Replies
View Related
Feb 26, 2013
we observe that the process platform causes about 50% cpu load of our Nexus 7010.Could not find any information for what this process is responsible to find out the root cause of the high cpu load.
View 1 Replies
View Related
Sep 9, 2012
Uhg. I deployed a 3560G a week ago and it was crashing... so I replaced it Sep 7 around 16:00 and now this one is crashing. Different logs.
Version 12.2(55)EX3
Sep 6 18:06:08: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 6 21:05:18: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 7 04:12:43: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 7 05:35:09: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 7 08:21:37: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 7 11:13:18: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Replacement Version 12.2(55)EX2
Sep 7 16:34:48: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 8 03:39:38: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 8 18:26:06: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 9 18:14:38: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
More detailed syslogs are in the attaced 'crash-logs.txt' file.
The device is running OSPF (it is in an NSSA). I have several other devices configured almost the same running the same IOS in my network and they are working fine.This does make the third out-of-box 3560C Cisco that has failed on me within a few days.
View 3 Replies
View Related
May 29, 2012
I know that an ELAM can be setup on a 6500 running ipservices 12.2(33)SXJ, however I noticed that following commands are not available on a 6500 router running advipservices 12.2(33)SXJ:show platform capture elam asic etc
So I wanted to know if there is an alternate way to setup an ELAM for troubleshooting purposes?
View 1 Replies
View Related
Feb 6, 2012
We have 2 x C6506E and 2 x C3560-48's, they are all interconnected via port channels at 2Gb per channel. The 6506's are running CEF but the 3560's are not (The 3560's carry all our server traffic).When I do a show CEF on the 3560's it says %IPv4 CEF not running. There does not appear to be a global command to enable CEF on these switches.Is this an IOS version option or is not supported on the hardware platform?
View 3 Replies
View Related
Dec 10, 2012
In our environment we have some HP chassis, and with them there are blade switches. Lately, we've been seeing some drops on few servers connected on the blade switch ports. The switch model is WS-CBS3120X-S. And below is the tx drop for two interfaces ( where the servers are connected to).
sh platform port-asic stats drop gi1/0/11
Interface Gi1/0/11 TxQueue Drop Statistics
Queue 0
Weight 0 Frames 0
Weight 1 Frames 0
[Code]...
View 1 Replies
View Related
Feb 20, 2013
I am trying to have F4 (the WAN interface) bridged to a VLAN interface. I have put my VLAN interface and my F4 in the same bridge-group, set an IP in the BVI Interface, and made sure that VLAN was properly trunked and configured on one of the router's switch ports
In other words, I need F4 to be treated as a switchport in access mode on my VLAN 10.
(...)
bridge irb
(...)
interface FastEthernet0
description trunk
switchport trunk native vlan 10
[Code].....
A ping in my vl10 VRF to 10.0.0.1 does not work. ARP does not resolve.
View 1 Replies
View Related
Mar 25, 2013
I have following requirements to implement on cisco asr1001 router.
1.G0/0/0 and G0/0/1 interfaces are connected to a swith through trunk. Multiple customers are will be using this trunk interface . Each customer will have subinterface with dot1q tag.
2 I want both sides of the ASR1001 to be in same segment .
3 If above two is possible I would like to implement shaping on each customers sub-interface level
is above implementation is possible on asr1001. configration and ios information. I found a technology called EVC . but I am not sure is that the one suited for me.
network diagram is attached seperately.
View 3 Replies
View Related
Aug 6, 2012
I have 2 networks.
NETWORK 1:EOC connection fro ISP going into a router (not the RV042) with a static WAN address from ISP. This router is hooked up to a switch that all the computers are connected to. All the computers on this network are using 192.168.1.x addresses. Most of these addresses are static, but the router is running DHCP in case we hook up temporary computers like laptops or client machines to this network.
NETWORK 2:DSL connection going into a router (not the RV042) with a static block of IPs from ISP. (8 IPs, 5 usable for the WAN interface, 1 static IP is being used for WAN interface). This router has a VPN connection set up for remote access to the linux machines on this network. This router is running DHCP on the LAN interface for this network with addresses 172.16.1.x. All the computers on this network are tied together with another switch, completely seperate from the 192.168.1.x network switch.
PROBLEM:We needed computers on the 192 network to be able to access computers on the 172 network. Someone decided to just run a cat 5 cable from the 192 switch to the 172 switch (not the routers, the switches). This "worked" - badly. Appearently there is a DHCP conflict (or something else going on) that was causing the router on the 172 network to try and assign addresses to the 192 network computers, and it was also "resetting" a connection about once an hour. This crashed our server on the 192 network. I disconnected that cat 5 cable between the two siwtches, and now each of the two networks are working properly, but they are now completely isolated from one another.
I need to create a bridge between the 2 networks so that machines on the 192 network can access machines on the 172 network while filtering out DHCP broadcasts from either network router to the other network. (I may need to filter out other protocols as well, but don't know yet.)So, I see 3 potential ways of doing this but don't know if they will work:
1) Can I just set up multiple subnets on the LAN interface of the RV042 and just run 2 cat5 cables from each switch on the two networks to the LAN ports of the RV042?
1a) If I do set up multiple subnets on the LAN interface of the RV042, do I need to assign the two ports to different VLANs? (I don't see any way to set each port to a specific IP address.)
2) Can I set up the 2 WAN ports on the RV042, one static for each network, and will the RV042 route traffic from 1 WAN port to the second WAN port?
3) Is there some other way I should consider setting this up?
Finally, someone mentioned that once I get the RV042 set up correctly as a bridge, I will need to route 172 addresses on the 192 network to the 192 interface of the RV042 via the DHCP router on the 192 network, and conversely, I will need to route 192 addresses on the 172 network from the DHCP router to the 172 IP interface of the RV042. I think this will be easy enough to set up in each of the DHCP routers...
View 3 Replies
View Related
Jan 19, 2012
I currently have a 2811 and a LAN setup via a sub-interface FA0/1.3 and using a HWIC-AP I have a sub-interface dot11radio 0/1.5. I have them setup to work and surf the inet great, but I have recently been overly annoyed with the fact that the wifi cannot access windows shares on desktops and visa versa with the laptops.
The trick to make this happen is currently they are not on the same subnet. I know the answer is bridging the interfaces but when I do this using the simple commands:
bridge 1 protocol ieee
interface x & y
bridge-group 1
Although what should be simple has failed (good thing I tftp'd my working config). Here is my current configuration.
interface FastEthernet0/1.30
encapsulation dot1Q 30
ip address 192.168.3.1 255.255.255.0
[Code].....
View 3 Replies
View Related
Dec 5, 2012
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies
View Related
Mar 6, 2012
When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies
View Related
Jan 30, 2012
Cisco 3725
IOS: (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T9
Wireless Module NME
Brief current running config below:
interface FastEthernet0/0
description WAN LINK
bandwidth 8192
[Code].....
View 2 Replies
View Related
Jan 20, 2012
I have a network where if an end user attaches an hub to the network, or rather one of those cheap unmanaged 8-port mini-switches and then plugs the two ends of the same cable into two ports of that mini-switch, all the network goes down. Loops are generated and many uplinks are shut down in err-disable state due to the loopback reason.
I know I could discourage the use of those mini-switches using port security. I even have NAC (cisco) deployed on the network, but there are cases where that mini-switches are allowed by the managment.In those cases, is not possible to exactly know wich hosts (mac addresses), and even how many of them will attach the network concurrently.As I know, they could even chain many mini-switch one to another. Of course, when even a single mini-switch is allowed on the network, it raises as a security hole.
Is there a way to allow the use of those devices without the risk of network outages? Some STP protection method? The best would be to have the Cisco access switch to get aware of the loop on its affected switchport (where the mini-switch is attached), immediately shutting down that port (to avoid loops on the network) and maybe sending an SNMP trap or a syslog message.
We are using Cisco Catalyst 2950 and 2960 for our access layer.
View 5 Replies
View Related
Aug 13, 2012
I need to bridge 2 subinterfaces; F0/0.301 and F0/0.302 on a single router.The router interfaces with a Cisco 2960 (LAYER-2) switch.QUESTION is, does a Cisco router support bridging on subinterfaces on the same physical interface?Currently this is NOT operational Spaiing-tree on F0/0.301 and F0/0.302 is down, switch side is forwarding for both Vlans.show ip interface brief shows up/down status of F0/0.301, F0/0.301 and BVI6 is down/down?
:
SETUP:
bridge irb
!
!
Interface F0/0
no ip address
[code]....
View 1 Replies
View Related
Feb 21, 2012
On a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies
View Related
Jan 23, 2013
I have faced a problem with configuring Cisco 3750G series switches as Sever farm switches with redudance.
servers have 2NIC (1GBps) and both are bridged for redundant connections.In both switches all ports get green coluor except one port on Secondary SW. I saw some Spanning tree block port status on that switch.when i type Show cdp neghbor command on switch i can see other switch through a server connected port. Also Spannig tree root bridge election is occured through that port . Simply i need to configure both switches to pass traffic through there uplinks them selves.. but it seems like Secondry switch pass its traffic through primary switch ( i think according to STP ) usinginterconnection of bridge port of a server. [code]
View 1 Replies
View Related
Apr 14, 2010
I have Cisco 7609 router and we have observed that router is rebooted due to the following error ;SLOT 3: Apr 13 16:06:26.621: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on Egress ESF Engine: Control Store Parity Error SLOT 3: Apr 13,Slot -3 we have SIP-400 card. We would like to know if there is any MIB which can monitir such reboots.
View 1 Replies
View Related
Jan 1, 2013
I have a Cisco 2801 with a 4 port Layer2 switch card installed (HWIC-4ESW).
How do I bridge Ethernet0/1 to the 4ESW so if you were to plug a computer into the 4ESW, it would be on the same network as Eth0/1? see my config below:
interface FastEthernet0/1
description Internal Interface
ip address 10.1.2.1 255.255.0.0
[Code].....
View 2 Replies
View Related
Aug 27, 2007
We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies
View Related
Nov 18, 2012
I want to ask about cisco 7600 model is it a switch or router or layer3 switch or Multilayer switch ?
here is the sh version :
===================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team
[code]....
View 2 Replies
View Related
Oct 9, 2011
i try newest ios 15.1(3)S0a and 12.2(33)SRE
in both case some times i obtain lowing traffic on interface and highest cpu - to 100%
after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s
CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
[Code].....
View 18 Replies
View Related
Jul 19, 2011
i have cisco 7600 router , here is show run : Gateway7600#sh run Building configuration...
Current configuration : 4787 bytes
!
! Last configuration change at 09:08:04 UTC Sat Apr 20 2013 by xxxx
!
version 15.2
service timestamps debug datetime msec
[Code]....
View 2 Replies
View Related
Mar 18, 2013
I have Cisco 7606 and wanted to test whether Cisco can drop frames due to invalid v lan ether type . i have configured the ports as
interface GigabitEthernet5/1
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet5/2
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
I have configured port also with encapsulation trunk dot1q ether type 88a8. i injected traffic with v lan ether type 0x8100. I expected to see drop traffic , however traffic passed in port to port.
View 1 Replies
View Related
Dec 6, 2012
i want to to ask about redirecting in MLS 7600 .assume the user a has an ip x.x.x.xand that user requested url...i want to to redirect his request to url...the users that have to pay the monthly bills , i want to give thim an ips and redirect all the http requests from this to a special local webpage .is is applicable to to it on router cisco 7600 ??or is it applicable on router 7206 npeg2 ? also i have siwtch 2960g.i dont want to do it by proxy server.
View 4 Replies
View Related
Sep 29, 2012
I am a soon to be network admin and have never set up a network to an existing network. Steps you need to add a new location to a company's network. For example if they are using 8 Building with 7600 Routers and 6500 and you need another building and they are using MPLS or Private Network, or Internet.
View 4 Replies
View Related
Sep 26, 2012
on 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies
View Related
Jun 13, 2013
Is it possible to configure MST on ASR and have rapid-pvst on 7600? can they interoperate? ASR sees no BPDUs and both are root bridges.
View 2 Replies
View Related
