I am a soon to be network admin and have never set up a network to an existing network. Steps you need to add a new location to a company's network. For example if they are using 8 Building with 7600 Routers and 6500 and you need another building and they are using MPLS or Private Network, or Internet.
View 4 Replies.We are setting up a new sales office where there will be between 5-10 users.At the moment, we run everything of one server which has all the file shares, printers. Active Directory etc. I know so far I will need the server cabinet - But my main concern is how I will make this new site connect to the already existing network and the other things which I will need.
View 4 Replies View RelatedI am having a problem trying to figure out how to add a new ASA 5505 to an existing network. My current network is:Cable Modem > Linksys > 48 port switch With multiple hosts residing on the 192.168.0.x network.Now i know that the ASA comes default with 192.168.1.1 on the inside interface and i want to change that to 192.168.0.1. I have tried to do this thru ASDM using the wizard and manually. Once i hit ok for it to write the config, it gives me an error that it didnt take. I then lose connection to the ASA and have to hard boot it to get it back.I am trying to do this without my external connection connected and i have a laptop connected to the ASA on port 0/2 with an IP address of 192.168.1.75.Do i need to connect my internet connection to it first and then run the wizard? I was hoping to get it configured for my existing network before i plugged in the internet connection to limit my downtime.This ASA came with 6.4.1 ASDM and 8.2 OS installed. i was able to upgrade the ASDM to 7.X but when i go to update the OS to 9.1, i get an error that i am not registered to use cryptographic software. Dont know where i need to register to get it?
View 4 Replies View Relatedwe are using 7609 router. it forwarding traffic to wards my firewall which was not allowd in my router. when ever im checking for routes in router using show ip route x.x.x.x its showing SUBNET IS NOT IN TABLE, but in workmy firewall dropped connection i can able to see that networks.
View 2 Replies View RelatedI have a WRT54G that has served us well for several years, but I needed a network connection in another part of the house, both wired for TV, and wireless for downstairs. So I ran an ethernet cable through the house and connected it to my new E1200. It's connected to Port 1, not the Internet port. The TV plugs into Port 2, and my Apple TV to port 3. So far so good, TV and Apple TV appear to work fine. Wireless is where I'm having problems, the wireless signals between the two routers appear on Wifi Analyzer I'm using. Both appear strong in signal for a second, then they disappear, then they appear again for a second, then they disappear. So the wifi's signals appear, then disappear and this cycle continues.
The WRT54G is setup with DHCP, channel 6.
IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: Enabled Start IP Address: 192.168.1.100 End IP Address: 192.168.1.149
The E1200 DHCP is disabled, channel 11, 20mhz.
Router IP Address: 192.168.1.2 Subnet Mask: 255.255.255.0 DHCP Server: Disabled Start IP Address: 192.168.1.1 (DHCP disabled) End IP Address: 192.168.1.50 (DHCP is disabled)
I've tried both routers named the same, and then tried 2 different names. I've rebooted them as well after making changes.
When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies View RelatedI have Cisco 7609 router and we have observed that router is rebooted due to the following error ;SLOT 3: Apr 13 16:06:26.621: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on Egress ESF Engine: Control Store Parity Error SLOT 3: Apr 13,Slot -3 we have SIP-400 card. We would like to know if there is any MIB which can monitir such reboots.
View 1 Replies View RelatedI want to ask about cisco 7600 model is it a switch or router or layer3 switch or Multilayer switch ?
here is the sh version :
===================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team
[code]....
I am trying to bridge the traffic(including different vlan traffic) from rtrA to rtrB using "bridge-group" functionality.I achived the same using a 7200 using the below configuration. [code] When I tried the same using 7600 router ping failed between rtrA and rtrB. Then from the documents it seems "bridge irb" is not supported in 7600.Is there any other way we can achieve the same fuctionality ( eg: using switchport also fine) ?
View 3 Replies View Relatedi try newest ios 15.1(3)S0a and 12.2(33)SRE
in both case some times i obtain lowing traffic on interface and highest cpu - to 100%
after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s
CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
[Code].....
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies View Relatedi have cisco 7600 router , here is show run : Gateway7600#sh run Building configuration...
Current configuration : 4787 bytes
!
! Last configuration change at 09:08:04 UTC Sat Apr 20 2013 by xxxx
!
version 15.2
service timestamps debug datetime msec
[Code]....
I have Cisco 7606 and wanted to test whether Cisco can drop frames due to invalid v lan ether type . i have configured the ports as
interface GigabitEthernet5/1
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet5/2
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
I have configured port also with encapsulation trunk dot1q ether type 88a8. i injected traffic with v lan ether type 0x8100. I expected to see drop traffic , however traffic passed in port to port.
I'm setting up an Ethernet network of Rockwell Stratix switches (badged Cisco 3000 series with extra firmware) and need a switch to obtain a gigabit port to a server as the Stratix switches only have 2 gigabit ports per switch and the network is in a ring. The Ethernet ring is in fibre and I would want copper to the server. The switch would need REP (Resilient Ethernet Protocol) to be compatable with the Stratix set up. Is the ME 3400G-2CS AC a workable option?
View 1 Replies View Relatedi want to to ask about redirecting in MLS 7600 .assume the user a has an ip x.x.x.xand that user requested url...i want to to redirect his request to url...the users that have to pay the monthly bills , i want to give thim an ips and redirect all the http requests from this to a special local webpage .is is applicable to to it on router cisco 7600 ??or is it applicable on router 7206 npeg2 ? also i have siwtch 2960g.i dont want to do it by proxy server.
View 4 Replies View Relatedon 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies View RelatedIs it possible to configure MST on ASR and have rapid-pvst on 7600? can they interoperate? ASR sees no BPDUs and both are root bridges.
View 2 Replies View RelatedI have a 7600 with ws-sup750 and when it boots it displays these errors:
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: [URL]
Firmware compiled 07-Apr-08 22:12 by integ Build [100]
00:00:05: %C6K_PLATFORM-0-UNKNOWN_CHASSIS: The chassis type is not known.(0x6003)
[Code]....
Then it got stuck in rommon, i tried using a 7200 pcmcia card (I downloaded the 7600 IOS there) but if i do from rommon boot disk0:
it complaints with :open: file "c7200-atafslib-m" not found so, it doesn't boot.
Anything I can do to be able to boot this device ?
I am a little stuck trying to troubleshoot unusually high cpu on 7600 Platform.This has been going on for many hours and not been causing a problem, but this doesn't seem replicated in our network and I am concerned about the cause.I have attached some output below, and disabled netflow on interfaces to free some switching CPU. How to track the cause of this? We only have routing protocols and 5 static routes to Null 0, so I cant see how this can be a route loop, but willing to stand corrected. Routes are learned from BGP with OSPF/MPLS internally on the network. This switch also connects to access switches on RIP and EIGRP.
No change has been made to this device when this problem started to occur so I am suspecting something about the traffic has changed or there is a rougue user? [code]
today i installed new router 7600 , but im facing some thing the cpu is increasing and it reached 50 % and still increasing as the bw dissipated is increasing .im applying ip policy which set next hop for many internet source my question is , how to know the cu percentage which is used by this ip policy , also , how to know the percentage by access-list ??
View 4 Replies View Relatedi have a 7206 router to be used as a gateway for internet router 7206 inerfaces are connected directly to cisco switch 2960g note that 7600 work only at 1 gega , and cant be used for 10 or 10 . im looking forward to use router 7600 instaed of 7206 i copied the config of 7206 and pased in 7600 but some commands which are under interfaces command was not accepted here is the config which as not accepted in 7600 router
%%%%%%%%%%%%%%%%%%%%%%%%
duplex auto
speed auto
media-type rj45
negotiation auto
%%%%%%%%%%%%%%%%%%%%%%%%
note that the 4 lines above was not accpted in 7600. does these commands will affect the new config ?i just want to ask before im trying to apply this config to production network?
Actually i have 7600 router and all trafic passes through Gi0/1(Routed port) interface to 6500 series switch. I need to create a vlan on this router eg. vlan 10 Any how it is possible assign a vlan to routed port and traffic of wan interfaces and the vlan traffic passed together.
View 2 Replies View RelatedES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
I have run into a problem testing static route failovers using ECMP. I have an edge device (SUT) that has 2 NIC interfaces to an internal Loopback. Each NIC is a unique Gi port on an 7609 VLAN tagged with unique IP subnets. The 7600 is configured to route the loopback via the 2 NIC. I am using CEF in the network for other traffic performance testing. Using an external sniffer we can verify that when a ping is initiated externall to the SUT loopback a specific path is selected by the router.
Ping host ------Network-----7609 Gi1/21 (172.16.110.9)-----------SUT Nic1 (172.16.110.10)
| |
| -------Loopback 137.168.68.114/32
| |
7609 Gi2/21 (172.16.110.73)------------SUT Nic2 (172.16.110.74)
[code]....
Now, when the selected path is taken out of server (pulling cable for example), the 7609 is not clearing the routing table to indicate that particular path is down and failing over to the secondary path. Other things I have noticed is the show ip cef still shows both peers as well as the arp table but the interface shows down (show interface gi1/21 for example). I am running 15.1. My understanding is that since the ports are directly connected to the router, the ports should be detected as down and any association of the IP for the down port should removed. This should trigger the static route to update the static route for the end destination to use the second path and traffic should continue.
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)BOOTLDR: Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
how to know if my bgp neighbour advertised my network from his side or not ???
here is my config :
Gateway7600#sh ip bgp
BGP table version is 8, local router ID is 192.168.40.3
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
[code]....
I need to set up existing printer & Scanned to work wire lees with wireless router that is installed in my home.
View 1 Replies View RelatedI need your input on how to appropriately introduce an N5K with Jumbo enanbled to a prexisting Core Network (Stack of Cisco 3750G Switches) without making any major alteration on the Core configs (everything is happy). The idea is to move two High I/O servers to the N5K during a transitional phase. I already have a fair understanding of what Jumbo-Frames are and what it does. Keep Jumbo-Frames within the N5K ONLY.
Conditions:
- Traffic is Data traffic, not storage/iSCSI
- The servers host our ERP applications and MySQL that is accessed heavily by users
- N5K to C3750G connectivity is a Port-Channel consisting of 4x1GB ports
- The servers are to remain on VLAN 2 (Data VLAN)
- The Core Switch is L3 and the boundaries reside here
I have configured a site to site VPN tunnel using my Cisco ISR 891 router. The tunnel connects between my network 10.88.10.0 to the remote network 10.210.65.0. When I ping the remote nnetwork my VPN tunnel comes up and all is well.
I have recently connected a second network to my 10.88.... network. The new local network is 192.168.0.0. I have now managed to get the two local networks pinging each other. I can also carry out RDP sessions between systems on both networks. Hence I am happy that both networks are communicating.
I used the Fastethernet Port 8 on my ISR 891 to physically connect to the new 192.168 network and then entered the appropraite 'Static Routes' on the 192.168 exisiting router(Netgear Router). Hence certain traffic arriving at the netgear will now be forwarded to Port FE8 on the cisco ISR 891.. See FE8 Port config at the bottom of this post. I have used tracert to ensure that the traffic does arrive at Port FE8,(192.168.0.235).
I cannot seem to ping any device on the remote 10.210.65.0 network from the 192.168 network. However, as stated above I can sucessfully ping the same remote device from the local 10.88 network. I must be missing something that allows the 192.168 traffic to use the existing VPN tunnel. I have added the following command to the IpSec rules for the VPN tunnel using the Cisco Configuration Professionla tool.
Permit 192.168.0.0/0.0.0.255 10.210.0.0/0.0.255.255 ip
I have several cabinets with top-of-rack N2K's attached to N5K's via FEX's. 9 cabinets with 2 switches each.
Recently I added 3 more cabinets to the mix, for a total of 12 cabinets with 2 switches each.
I can get into the new switches and see the FEX's and configure ports, etc. but no device I attach to the 'new' N2K's is pingable over the network. I can take the same device, same cable, and attach it to a legacy N2K talking to the same N5K's, and it immediately joins and is pingable over the network
I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.
View 2 Replies View RelatedI've a situation where I need to add a new 3750x to a existing stack of 3750. [code] When I tried to stack them together, I get a version mismatch error. Is this because of the difference in SW Image? What are my options next ? My ultimate goal is to make the new switch stack correctly with the exisitng switches.
View 11 Replies View RelatedWe've recently inherited a platform with little handover and also minimal networking experience.We're going 100 miles an hour in learning, but I'm a bit confused with the idea of a L2 switch with no IP assignments to ports, so using VLANs, and a L3 switch with IP assignments. And the combination of both.We have 2 Cisco 3750 switches, along with a whole host of other hardware, so we're starting at this "gateway" to start breaking things down.
View 7 Replies View RelatedWhen you use the command switchport trunk allowed vlan add [vlan-id]There should be no drop in service to the existing VLANs, correct? I am trunking from a 7K to a 2960S via 2G PoCh.
View 2 Replies View Related