Cisco Switching/Routing :: Copying Configuration From 7206 To 7600 But Some Is Not Accepted
Jul 27, 2012
i have a 7206 router to be used as a gateway for internet router 7206 inerfaces are connected directly to cisco switch 2960g note that 7600 work only at 1 gega , and cant be used for 10 or 10 . im looking forward to use router 7600 instaed of 7206 i copied the config of 7206 and pased in 7600 but some commands which are under interfaces command was not accepted here is the config which as not accepted in 7600 router
%%%%%%%%%%%%%%%%%%%%%%%%
duplex auto
speed auto
media-type rj45
negotiation auto
%%%%%%%%%%%%%%%%%%%%%%%%
note that the 4 lines above was not accpted in 7600. does these commands will affect the new config ?i just want to ask before im trying to apply this config to production network?
View 3 Replies
ADVERTISEMENT
Oct 3, 2012
i have to configure 80 Cisco 876 routers, so i planned to copy config via tftp from one configured router to PC, edit it in text editor (change ip addresses, dhcp pools, vpn keys...) and then copy it via tftp to another router, etc... Configuration looks fine and it works when i paste it in cli, but when i copy it via tftp i'm getting strange problems like dhcp not working or snmp not accessible. Am I missing something.
Here's config from router with dhcp problem:
ROUTER#sh run
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers(code)
View 2 Replies
View Related
Nov 24, 2012
Recently we have upgraded from a cisco 7200 environment to an ASR1002 having to migrate the configs as well.The command "ntp update-calendar" is not accepted in the config migration , any reason why ? doesnt the ASR have an internal hardware clock ?
View 2 Replies
View Related
May 1, 2012
I just upgrade a license on a cat 4510. The license installed but the EULA was not accepted and it will not upgrade to the new feature set.
View 1 Replies
View Related
Nov 5, 2011
Here is logs from 2650 router.
2650XM#$ Nov 5 23:10:13.929 MST: %SIGNATURE-3-NOT_ABLE_TO_PROCESS: %ERROR: Not able to process Signature in flash:2600-adventerprisek9-mz.124-25d.bin.Nov 5 23:10:41.963 MST: %SIGNATURE-3-NOT_ABLE_TO_PROCESS: %ERROR: Not able to process Signature in nvram:.
Nov 5 23:11:26.642 MST: %SYS-2-EXCEPTIONDUMP: System Crashed, Writing Core....2650XM#$
Right now i am able to access the router . whats this error about -- is router going to crash or reboot?
View 26 Replies
View Related
Feb 28, 2012
Our office lan network is in 192.168.0.0/16 with 300 nodes and 30 server .Since its a large broadcast domain some times it takes large time for copying files.How can we avoid this problem with out changing the subnet.Also how to avoid broadcast storm.we are using cisco 2950 series switch.
View 10 Replies
View Related
Jun 4, 2012
I was upgrading IOS on 4507 R with dual supervisor.I download the IOS on Active supervisior and did reboot.After reboot i login to switch then i got switch standby prompt.I found that after reboot active supervisior became standby supervisior.
Now new IOS is on standby supervisior.Need to confirm below..So this means that IOS does not syn within the supervisiors as compared to config right ?
-Which command i can use that will copy IOS from standby supe to Active supe??
-Which command i can use that will show both active and standby supe with new IOS?
-Is there any command that i can use to switchover from active to standby supe??
View 3 Replies
View Related
Aug 21, 2012
i hav asa5520 i copying configuration from PIX to ASA5520 (7.2) everything working fine bt problem is that after sometime my DMZ interface losing connectivity ...
View 1 Replies
View Related
Feb 9, 2012
I just received a DIR-615 in the post that I bought on eBay. I currently have a DI-624 at home .Will I be able to copy the configuration from my old router to this new one?
View 3 Replies
View Related
Oct 28, 2012
I will upgrade ios image to router 7206vxr, only have doubts, is necesary upgrade
View 2 Replies
View Related
Jul 15, 2012
Router CPU is staying high. No changes to configuration in a while.
Plt-72-7206-2#show proc cpu sort | ex 0.00
CPU utilization for five seconds: 91%/87%; one minute: 88%; five minutes: 90%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
42 1116663516 34369829 32489 1.55% 1.57% 1.55% 0 Per-Second Jobs
3 12184 479 25436 0.73% 0.18% 0.09% 2 SSH Process
2 10062364 6316855 1592 0.24% 0.18% 0.22% 0 Load Meter
[code]....
View 4 Replies
View Related
Jul 6, 2012
How do i copy the configuration file from a switch to a storage device (USB)
View 1 Replies
View Related
Sep 5, 2012
I have a MPLS cloud in our data center. I want one network coming into our core router to have a different default route than the other networks coming in. I'm getting hits on the acl but the route isn't applied and goes to the default route that is configured in the router. I have other PBR for setting local-preferences and as-paths and they are working fine.
The router is a 7206 Version 12.4(11)T3
!
ip route 0.0.0.0 0.0.0.0 1.2.3.4
!
ip access-list extended 2nd_Default_Route
[Code].....
View 1 Replies
View Related
Nov 18, 2012
Has come across issues with multiple GRE tunnels between two devices when using the same source and destination addresses. I've tried using tunnel keys but this makes no difference. The only way I can get this to work is between different source & destination addresses.
View 4 Replies
View Related
Mar 6, 2012
When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies
View Related
Apr 14, 2010
I have Cisco 7609 router and we have observed that router is rebooted due to the following error ;SLOT 3: Apr 13 16:06:26.621: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on Egress ESF Engine: Control Store Parity Error SLOT 3: Apr 13,Slot -3 we have SIP-400 card. We would like to know if there is any MIB which can monitir such reboots.
View 1 Replies
View Related
Jul 19, 2012
I have configured below SNMP v3 commands in Cisco Router 7206VXR (NPE-G1) . I have tested with all option but it is not working . SNMP server is a SNMPc tool and I have configured user name and piv and authentication credential correctly in both side . Same configurations is working for all Cisco switches but not working for Cisco Router.
SNMP V3 configurations:
access-list 20 permit 43.194.10.0 0.0.0.255
snmp-server view readview iso included
snmp-server group readonly-group v3 priv read readview access 20
[ code]....
Router :
Host Name# sh versionCisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.2(33)SRD7, RELEASE SOFTWARE (fc1)[ code]...
View 3 Replies
View Related
Jun 22, 2011
There are some troubles in my 7206 vxr . The process of this problem below.
LOG:
Self decompressing the image : ####################################################################################################################################################################################################################################################################################################################################################################
[Code]...
View 2 Replies
View Related
Jan 10, 2011
ROUTER#sh run | i ip cefip cef table event-logip cefip cef accounting non-recursive load-balance-hash ip cef accounting non-recursive external
>snip<
ROUTER#conf tEnter configuration commands, one per line. End with CNTL/Z.ROUTER(config)#no ip cef accounting non-recursive load-balance-hashCommand authorization failed.
% Incomplete command.
ROUTER(config)#no ip cef accounting non-recursive load-balance-hash ?% Unrecognized commandROUTER(config)#^Z
cisco 7206VXR (NPE-G1) processor (C7200-JS-M), Version 12.3(10c)
How do I remove "ip cef accounting non-recursive load-balance-hash" from the config. I'd like to leave the box as I found it. Is it to do with an authority level or something more?
View 3 Replies
View Related
Nov 18, 2012
I want to ask about cisco 7600 model is it a switch or router or layer3 switch or Multilayer switch ?
here is the sh version :
===================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team
[code]....
View 2 Replies
View Related
Apr 24, 2013
I am trying to bridge the traffic(including different vlan traffic) from rtrA to rtrB using "bridge-group" functionality.I achived the same using a 7200 using the below configuration. [code] When I tried the same using 7600 router ping failed between rtrA and rtrB. Then from the documents it seems "bridge irb" is not supported in 7600.Is there any other way we can achieve the same fuctionality ( eg: using switchport also fine) ?
View 3 Replies
View Related
Oct 9, 2011
i try newest ios 15.1(3)S0a and 12.2(33)SRE
in both case some times i obtain lowing traffic on interface and highest cpu - to 100%
after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s
CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
[Code].....
View 18 Replies
View Related
Dec 22, 2011
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
View 2 Replies
View Related
Jul 19, 2011
i have cisco 7600 router , here is show run : Gateway7600#sh run Building configuration...
Current configuration : 4787 bytes
!
! Last configuration change at 09:08:04 UTC Sat Apr 20 2013 by xxxx
!
version 15.2
service timestamps debug datetime msec
[Code]....
View 2 Replies
View Related
Mar 18, 2013
I have Cisco 7606 and wanted to test whether Cisco can drop frames due to invalid v lan ether type . i have configured the ports as
interface GigabitEthernet5/1
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet5/2
no ip address
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
I have configured port also with encapsulation trunk dot1q ether type 88a8. i injected traffic with v lan ether type 0x8100. I expected to see drop traffic , however traffic passed in port to port.
View 1 Replies
View Related
May 28, 2013
I have a 7206 VXR router between a several Mikrotik routers on our backbone. We have the Mikrotiks on both sides of the CIsco 7206VXR setup for MPLS/VPLS. I need to simply setup the 7206 to pass the MPLS/VPLS tagged packets to the next router on the link. We are using OSPF as the routing protocol. I am told by our Mikrotik guy that I just need to enable LDP and VPLS tunnels 4:0 on the 2 gig interfaces on the 7206VXR to let it pass the MPLS/VPLS traffic. It sounds simple but I'm not sure how to do this.
Any commands I need to imput to allow this router to pass this MPLS/VPLS traffic.
View 1 Replies
View Related
Dec 6, 2012
i want to to ask about redirecting in MLS 7600 .assume the user a has an ip x.x.x.xand that user requested url...i want to to redirect his request to url...the users that have to pay the monthly bills , i want to give thim an ips and redirect all the http requests from this to a special local webpage .is is applicable to to it on router cisco 7600 ??or is it applicable on router 7206 npeg2 ? also i have siwtch 2960g.i dont want to do it by proxy server.
View 4 Replies
View Related
Sep 29, 2012
I am a soon to be network admin and have never set up a network to an existing network. Steps you need to add a new location to a company's network. For example if they are using 8 Building with 7600 Routers and 6500 and you need another building and they are using MPLS or Private Network, or Internet.
View 4 Replies
View Related
Sep 26, 2012
on 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies
View Related
Jun 13, 2013
Is it possible to configure MST on ASR and have rapid-pvst on 7600? can they interoperate? ASR sees no BPDUs and both are root bridges.
View 2 Replies
View Related
Apr 27, 2011
I have a 7600 with ws-sup750 and when it boots it displays these errors:
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: [URL]
Firmware compiled 07-Apr-08 22:12 by integ Build [100]
00:00:05: %C6K_PLATFORM-0-UNKNOWN_CHASSIS: The chassis type is not known.(0x6003)
[Code]....
Then it got stuck in rommon, i tried using a 7200 pcmcia card (I downloaded the 7600 IOS there) but if i do from rommon boot disk0:
it complaints with :open: file "c7200-atafslib-m" not found so, it doesn't boot.
Anything I can do to be able to boot this device ?
View 15 Replies
View Related
Nov 16, 2011
I am a little stuck trying to troubleshoot unusually high cpu on 7600 Platform.This has been going on for many hours and not been causing a problem, but this doesn't seem replicated in our network and I am concerned about the cause.I have attached some output below, and disabled netflow on interfaces to free some switching CPU. How to track the cause of this? We only have routing protocols and 5 static routes to Null 0, so I cant see how this can be a route loop, but willing to stand corrected. Routes are learned from BGP with OSPF/MPLS internally on the network. This switch also connects to access switches on RIP and EIGRP.
No change has been made to this device when this problem started to occur so I am suspecting something about the traffic has changed or there is a rougue user? [code]
View 2 Replies
View Related
Jul 29, 2012
today i installed new router 7600 , but im facing some thing the cpu is increasing and it reached 50 % and still increasing as the bw dissipated is increasing .im applying ip policy which set next hop for many internet source my question is , how to know the cu percentage which is used by this ip policy , also , how to know the percentage by access-list ??
View 4 Replies
View Related
