Recently we have upgraded from a cisco 7200 environment to an ASR1002 having to migrate the configs as well.The command "ntp update-calendar" is not accepted in the config migration , any reason why ? doesnt the ASR have an internal hardware clock ?
View 2 RepliesI just upgrade a license on a cat 4510. The license installed but the EULA was not accepted and it will not upgrade to the new feature set.
View 1 Replies View Relatedi have a 7206 router to be used as a gateway for internet router 7206 inerfaces are connected directly to cisco switch 2960g note that 7600 work only at 1 gega , and cant be used for 10 or 10 . im looking forward to use router 7600 instaed of 7206 i copied the config of 7206 and pased in 7600 but some commands which are under interfaces command was not accepted here is the config which as not accepted in 7600 router
%%%%%%%%%%%%%%%%%%%%%%%%
duplex auto
speed auto
media-type rj45
negotiation auto
%%%%%%%%%%%%%%%%%%%%%%%%
note that the 4 lines above was not accpted in 7600. does these commands will affect the new config ?i just want to ask before im trying to apply this config to production network?
see the attached diagram to explain the network. I'm trying to do a "port-to-port" layer 2 connection on an ASR that will bi-directionally bridge a physical interface to a sub-interface. I tried using " connect VLAN200 Gig0/1/0 Gig0/0/3.200 interworking ethernet " but I'm not getting traffic through the connection.
I don't think BDI will work because it requires a Layer 3 point. I have to make this Layer 2 switching.
I need to interface an ASR1002 to an ONS-14454 via multimode fiber The ASR1002 will use the 1000Base SFP-GE-S SFP module in one of the built-in Ethernet ports (in 1 of the four ports) The ONS-14454 will use 10/100/1000Base ONS-SI-GE-SX SFP in the Ethernet expansion blade.
Cisco docs indicate each module is supported in specific ASR and ONS but does not indicate interfacing between the two. If these two modules will communicate without error via multimode fiber?
Is the onboard interfaces on an ASR router (4x on ASAR1002, 6x on ASR1002-X) are fixed gigabit or are they 10/100/1000 ?
I assume the interfaces on the 8port Gigabit SPA module are fixed gigabit speed ports (why otherwise sell a 10/100 8port SPA module also ?) no ?
I am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies View RelatedI have a cisco 877-k9 router whit 12.<15>T5 system, dram 128MB and 24MB. I want upgrade this correctly. Where is ios correttly supported?
View 4 Replies View RelatedI am trying to update a switch I bought to the latest IOS using the Cisco Network Assistant but the it is failing becasue it's saying I dont have the space.
In the CLI I get,
Switch#dir all-filesystemsDirectory of flash:/
2 -rwx 109 Mar 01 1993 00:01:47 +00:00 info 3 -rwx 270 Jan 01 1970 00:01:37 +00:00 env_vars 7 -rwx 3081999 Mar 01 1993 00:03:23 +00:00 c2950-
[Code]....
I got 10 Catalysts 3750 (all of them identical) and I got the IOS Update. Anyway I only have service contract for 4 of them.
Am I allowed to update all of them? Or only the four devices which have the service contract?
I bought a secondhand small business router (model 1941 Integrated Services Router) for personal use. It runs version IOS 15.0(1)M1 software, which seems to work well, but I'd like to download a firmware update that addresess some of the security flaws in this software. When I tried the download process it told me I need to buy a service contract first? Is this right, or am I doing something wrong?
View 1 Replies View RelatedI plan to buy WS-C3560CG-8PC-S (Catalyst 3560-C) for my home lab. I just created a new account on [URL] (I did not register any equipment or contract for that new account). I was able to download ios 12 and 15 for that switch.- Will I be able to flash one of these versions when I will have the new switch ?Cisco warranty for these Switchs (Enhanced Limited Lifetime Hardware Warranty,[URL] says NO OS Software Updates included. Does tha mean that I can download ios updates but won't be able to flash the device or use it ?- Do I really have to buy Smartnet support to be able to update ios for that switch ?
View 7 Replies View RelatedI have an Cisco 3550 48 SMI running IOS (tm) C3550 Software (C3550-I9Q3L2-M), Version 12.1(13)EA1a. Software advisor says that I can only update to Version 12.1(22). The software download area tells me that the latest version is 12.2(44).
know if I could use the latest 12.2? Or has the hardware changed with the IOS versions?
I have a 2 member 3750-x switch stack that was upgraded to 15.2 today via CNA. All the files were transfered and expanded correctly and it got to the step where the switches needed to be reloaded but on reload they froze.
I connected a console cable and power cycled the stack. I see the flash initialize and then the IOS image start to load. Lots of @ symbols and then nothing. It just sits there. The system light on the switches, while flashing green during the load, is now off. No light at all. But fans are running and the process will repeat itself if power cycled.
, I am trying to change the default IP address in vlan 1 on a cisco 861 but everything I do so my connection via SSH hangs and all ssh/telnet attempts are refused.
my commands are as followed:
int vlan 1
ip address 192.168.1.1 255.255.255.0
[hangs]
my current vlan 1 address is 10.10.10.1 255.255.255.0
my vlan1pool on dhcp
is an address range of 192.168.1.0/24
do i need to update something in the authenication to allow connections from 192.168.1.0/24 instead of 10.10.10.0/24
I've recently tried to update the modem firmware on an 887M that is actually using an Annex M service and after rebooting to kick in the new modem firmware, the router loses sync. I've tried this with various other 877, 877M, 887 and 887Ms on normal Annex A services with no problems, but this Annex M service doesn't like it at all.
View 2 Replies View Relatedyou can update your ios for free within the 90 day warranty.e.g. a customer bought a asa 5510 and installed was a old version of the ios. now our customer complains that he wants to have the current version.but as far as i know he would need a smartnet in order to get the current ios.
but i think to remember that someone told me that you can update your ios device withthin the 90 day warranty. true?
ive updated my catalyst 4948-10GE to version 15.0(2)SG1.Now it is not possible to login by ssh or telnet on this switch. the access is established over the mgmt-Interface and vrf.i get a ping reply but login is no more possible now.is there an new feature in this version for vrf or remotelogin that has to be configured? if neccessary i can paste the running-config here.
View 3 Replies View RelatedI am having trouble updating the epld image on the 10gb Module of Nexus 7k. we have two nexus and two 10gb module. Tried the other one and it worked fine. its jsut the first one that has problems with the epld image. i have tried on both the nexus on two different slots and still the same error.
I get the following error:
Chain connectivity is broken while upgrading the FPGA. (Error Number : 36)
This feature doesn't work as advertised on the Release Notes and other documentation. After 12 hrs of lab work and a tlwo day support call to TAC, they finally came back to me that:
IOS Upgrade works well if you use the command force-reload, without force-reload, it won't work. --"of course with this command the complete stack will go down and the purpose of RSU will not serve"
Then they pointed me to a bug that I could not find in the bug tracker unless I searched by the bug ID number ?? CSCua78897
Unfortunately this bug has a closed status and is not slated to be fixed ?
cisco WS-C6509-E Core switch with IOS "s72033-ipservicesk9_wan-mz.122-18.SXF11"
i have 2 question
Q.1 i want to upgrade this switch what is the latest IOS ver. supported by this module ?
Q.2 i need to enable http server on this switch when i run this comman it's accsebt but i cant get http work
Basically I have netflow which i'm trying to use to export to a netflow collector. I'm pretty sure that the 3750-X does support netflow. I've recently updated IOS on the 3750-X to support flexi netflow.For some reason the netflow packets are not being exported to the server. I'm using Opmanager which should present the netflow stats in the form of a graph. I'm using a universal IOS image. (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2 3750-X WS-C3750X-24T-S
View 12 Replies View RelatedI am working at a client site today on a routing issue. I am currently working on an issue where a 3750 switch running EIGRP will not update its neighbor router when a network statement is added to the eigrp instance.The neighbor is a 3825 router.
Both the switch and the router have a common network which is 192.168.36.0/24.
Both the switch and the router are in a neighbor adjacency.
Both boxes have "no auto-summ" in the routing configuration instance.
I can run debugs on both routers (debug eigrp packets) and then I can watch queries and updates when I issue "auto-summ" or "no auto-summ". Also I see a "graceful restart" for the peers when this is done.I had an expectation that when I added the network (this is just an arbitrary network for testing, which is 172.16.69.0/24). I wanted to watch this network being sent in an update to the neighbor router.When I add the above mentioned network, there are no updates packets sent from the 3750 to the 3845. I have not had success to this point trying to resolve. I have followed the Cisco document "Troubleshooting EIGRP Flow Chart", but have exhausted all it has to offer and now it is at the point where it is telling me to contact TAC.
We recently installed Cisco 6509-E with dual Sup 720-BXL. We are using this switch on internet Edge. Internet connection is terminating on 10GIG fiber port.We do have following line cards installed.
1. 10 GIG * 4 port line card
2. 1 GIG * 8 port line card
3. Empty
4. Empty
5. Sup 720-3BXL
6. Sup 720-3BXL
7. 1 GIG * 48 ports
8. 1 GIG * 48 ports
9. 1 GIG * 48 ports
We do have 2 GB internet pipe.We are running load test sending http port 80 request and when load reach to arround 100 to 200 mbps and connections from out side to inside 80,000 switch start reponding very very slow and start packet loss and when I try to ping from one server to second server it show normal ping but if I tried to ping gateway IP of server which is SWITCH IP it show packet loss and very high letancy.
Switch also throw message "No memory available: Update of NVRAM configuration failed"
I am using Packet Tracer to simulate Cisco networking.As the existing IOS of the 3560 and 2960 switch are in older version which has no new feature in new IOS, how to upgarde the IOS of Cisco switch at Packet Tracer?
View 5 Replies View RelatedThe ASR1002/1002F are touted to be able to handle large routing tables. They are also touted to have the software based IOS HA.What is not stated is that once IOS HA is turned on, the memory left in the router is so miserable that only 1 view of the internet GRT is pratically possible. My grumble is that this isn't documented anywhere and only more recently when the RP2 was launched has this been "corrected". But we have 7 units of ASR1002/1002F all not living up to their initially advertised functionality.
View 2 Replies View RelatedI am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not.also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Master switch has new boot path but unable to change in slaves.
View 1 Replies View RelatedTrying to get internet on a very old PC. It's an old PC. But it's for an 8 year old. I just formatted the PC. Ethernet card was recognized. Not showing any issues in the device manager either. But when I choose my WN from the WNL and click connect, my password doesn't seem to work. It looks like it's connecting, but never does?
View 14 Replies View RelatedI have set up my first server. Its a HP N40L microserver & it works well but, after installing MythTV, when I try to run the backend I am asked for a password. I put in the admin password & it tells me the password is wrong. I have tried every password I can think of.
View 8 Replies View RelatedI used to be able to connect to my internet with other computors but now it keeps saying we have the wrong password.
View 2 Replies View RelatedWhat are the steps I need to take to correct this so we can download books from amazon .Password on Kindle is not accepted by the Linksys router
View 2 Replies View RelatedI bought this router (DIR-655) some time earlier this year, so it hasn't even been half a year that I've owned the thing. I set it up in the small duplex I was sharing with my sister and it worked quite well. Actually... for the first 45 minutes I was freaking out because I was getting practically no signal, then I realized I had forgotten to screw in the antennas... but that little anecdote aside, it worked fine.
I've since moved into a new place. I got a new modem, still on Videotron, I just upped the speed from 7 MB/sec to 15 MB/sec. Before setting up the router I inserted the CD that came with it and followed the instructions therein... things seemed fine, except that he automatically used the same network name that I used at my last place... almost like he was stuck on it. I couldn't figure out how to create a fresh new network. But I shrugged it off and continued, entering my own password and everything else.
Now, at the end he gave me 4 pieces of information,
A router password. A network name (SSID), this is the one who's name was stuck to the old one. A network security type, I went for Most secure(WPA) And the network security key, this was a randomly generated alphanumeric code of some sort.
I copied this in two different ways and the installation wizard automatically saved me a copy onto the desktop, so I know for certain I got the passwords right. I pulled out my iPad later, saw the network, a good strong signal, and tried to connect except it's not accepting my password. The password I triple-saved and checked without a shadow of a doubt. On a whim I tried to use the Security Key, and that seemed to connect for some reason, but it is considerably slower than it was at my last place.
The modem isn't to blame (it's running on double the speed now) and the signal strength is good. It's just that something gone weird with the password, and it feels very slow. Even if it wasn't slow, I would really like to know why none of my wifi devices are accepting the password I assigned.
And I used that http://192.168.0.1/ trick to look into the router settings from my computer. I changed the network password into something new. And still none of the devices will connect, they keep telling me it's the wrong password. I am only able to connect through the Security Key and I don't like that! I tried to contact D-Link's technical support the other day, but it drew on for so long my cellphone actually ran out of minutes.
Short Version: None of my wifi devices are accepting the password I gave during the setup and I don't know why!
I'm running a 64-bit Windows 7 on 1-year old dual-core desktop computer.
I have 3 WLC 5508 and a NAC guest server. We want to download a wildcard certificate after a few seconds at the download of this certificate I got the failure message download failed.
Accept the WLC wildcard certificates or must I generate a SAN (Subject Alternative Name) Certificate.