Cisco Switching/Routing :: ASR1002 Interfacing To ONS-14454 Via Mm Fiber
Feb 7, 2012
I need to interface an ASR1002 to an ONS-14454 via multimode fiber The ASR1002 will use the 1000Base SFP-GE-S SFP module in one of the built-in Ethernet ports (in 1 of the four ports) The ONS-14454 will use 10/100/1000Base ONS-SI-GE-SX SFP in the Ethernet expansion blade.
Cisco docs indicate each module is supported in specific ASR and ONS but does not indicate interfacing between the two. If these two modules will communicate without error via multimode fiber?
View 2 Replies
ADVERTISEMENT
Jan 17, 2012
see the attached diagram to explain the network. I'm trying to do a "port-to-port" layer 2 connection on an ASR that will bi-directionally bridge a physical interface to a sub-interface. I tried using " connect VLAN200 Gig0/1/0 Gig0/0/3.200 interworking ethernet " but I'm not getting traffic through the connection.
I don't think BDI will work because it requires a Layer 3 point. I have to make this Layer 2 switching.
View 5 Replies
View Related
Nov 24, 2012
Recently we have upgraded from a cisco 7200 environment to an ASR1002 having to migrate the configs as well.The command "ntp update-calendar" is not accepted in the config migration , any reason why ? doesnt the ASR have an internal hardware clock ?
View 2 Replies
View Related
May 23, 2013
Is the onboard interfaces on an ASR router (4x on ASAR1002, 6x on ASR1002-X) are fixed gigabit or are they 10/100/1000 ?
I assume the interfaces on the 8port Gigabit SPA module are fixed gigabit speed ports (why otherwise sell a 10/100 8port SPA module also ?) no ?
View 2 Replies
View Related
Dec 19, 2012
I am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies
View Related
May 23, 2012
Someone had told me the 6500 switches can be stacked via fiber. This feature is available for the 3750s?
View 7 Replies
View Related
Jul 10, 2012
Can I use the SFP-10G-SR 10g interface woth Multi - Mode fiber?
View 3 Replies
View Related
Dec 24, 2011
We have Three locations (A,B,C) across campus. Location A is Main Location, While B & C are remote locations. Distance among all locations approx. 2 miles.
I want 10G Fiber among these three locations. I am taking 4510+E with SUP 7E with Redundant SUP & 10G Fiber line card(X2 10G) at Location A.At Location B & C, i need Max. 2 Nos. of 10G uplink. i am taking 4507r+E with redundant SUP 7LE. Can i terminate 10G Fiber UPLINK from Location A in to Redundant SUP 7L-E(10G SFP+) at location B & C ??
At one time, Primary SUP 10G uplink should be active & Redundant SUP 10G uplink should be standby. When primary SUP fail, redundant SUP 10G uplink will be active. Is that Possible with this scenario?Is that possible that at same time, 10G Uplink on both SUP 7L-E be Active?
View 7 Replies
View Related
Oct 20, 2012
When you aggregate multiple fiber GBICs together on the 3508G, do you configure it as an etherchannel, or as fibre-channel? I've looked around online for hours, but can't find it mentioned anywhere.
View 3 Replies
View Related
Sep 2, 2012
I am trying to connect a 6509 switch to a 4503-E switch using single mode dark fiber over a distance of less than half a mile. Although a routine task, it does not work..We have a care 6509 switch where we concentrate all of our dark fiber connections for our remote sites. The 6509 switch already has 30 remote sites, most of them with 4503-E switches, connected in this way therefore it is a tested scenario. For the connections we use the GLC-LH-SM SFPs on both switches. Out of these 30 sites we had a similar problem with two of them, which we solved with the use of CWDM SFPs. With the CWDMs the fiber came up right away. However, I cannot keep using this solution because it is way too expensive! I had the losses of the fiber measured end-to-end and they are negligible (>0.5 dB).
In this latest case, like I said, we could not bring the connection up between the core 6509 switch and the 4503-E switch using the GLC-LH-SM SFPs. I then replaced the 4503-E switch with a 3560 and the link came up! Then I tried using a CWDM-SFP in the 4503-E, while keeping the GLC-LH-SM SFP in the 6509 and the link came alive again! Of course we already tried replacing the fiber patch cords with no luck. [code] I find it very weird for the link to work with the 3560 or with a CWDM in the 4503 but NOT with the SFP in the 4503!
View 6 Replies
View Related
Mar 22, 2012
Company I work for just moved into a new location. We have two data closets which are patched as independent entities, with no Ethernet tie connection. These closets are roughly 100 feet apart.
There is a fiber connection that runs between both closets, that the previous tenant used to connect the switches. I have placed a Cisco 2960 switch in each location, and added one mini SFP gbic's to each switch. After attaching both sides, neither light up. I do a sh inter gig1/0/49 on each and shows 'down down' (not admin down).
What is the trick on getting these to communciate, do I need to configure these ports, and are they supposed to light up?
What I am trying to accomplish is to get the one closet that is completely cut off, communicating by logically stacking, or 'daisy chaining' via fiber.
I turned off the lights and popped the fiber out, and I do see a faint red light (I did not look straight into it), so I think the fiber is active.
View 2 Replies
View Related
Apr 29, 2013
I am working on a project to connect 2 switch stacks via 10 Gb fiber. I am told that the 3750Xs do not natively receive the 10 GB SFPs. What part numbers do i need to order to make this work? Is there any IOS image requirements?
View 14 Replies
View Related
May 23, 2012
Using SFP-10G-LRM with single mode fiber? We have 1310nm.
View 2 Replies
View Related
Sep 4, 2012
I have a c3560 switch that has two gig fiber modules in it. I need to uplink fiber to one of these at 100mb. This is because this port will be rate limited to 20mb and 10 percent is the lowest you can go with the rate limiting command. Is there a 100mb fiber module i can insert in the 3560
View 1 Replies
View Related
Nov 3, 2011
I have three switches:
primary - Cisco Catalyst 3750G-24TS-24
and two SG300-28
I need to apply uplinks as follows:
3750G-24TS-24 SFP (1) -> SG300-28 (first) mini-GBIC (1)3750G-24TS-24 SFP (2) -> SG300-28 (second) mini-GBIC (1)SG300-28 (first) mini-GBIC (2) -> SG300-28 (second) mini-GBIC (2)
I would like to know, What type of mini-GBIC and SFP and cable I should use for SX Multimode?What max speed rate I will get?
View 8 Replies
View Related
Mar 7, 2012
I have an old Cisco 3500XL I am using for my home lab, but was wondering can I use the fiber ports to connect to my PC. I have to correct NIC interfaces but no link indication. I did make sure the port was no down, but sill not link.
View 8 Replies
View Related
May 22, 2013
This is an easy question for all the architechs and designers out there. I have a stack of 3508-XL switches and one of them failed. we have 2 spares but hese are more than 10 years old and have reaced EoL.What is the equivalent switch of a 3508-xl replacement today?
View 11 Replies
View Related
Dec 12, 2012
I have a WS-X6816-10G-2T module with X2-10GB-SR modules. I will be getting a SMF hand off and the length of the termination is around 100 meters. (I will be getting another hand off for Inter-DC link for which I have X2-10GB-LR module). The question is can I connect this SMF hand off (short length) on the SR module?
View 2 Replies
View Related
Jul 18, 2011
I have issue with connectivity 3750G with Dlink Switch, it cannot connect to non-cisco switch with fiber , But CISCO to CISCO switch it shows connectivity. My question is that is there any configuration on Cisco 3750G switch to connect with non-cisco switch through fiber (SFP) ?
View 2 Replies
View Related
Jan 14, 2013
I need Know what connection is using on Cisco 2811 router.I have this interface in Cisco 2811, I need Know if this port is connected to Fiber or Copper. I think is copper with RJ45 but I see 100 base TX/FX so this make me doubt about it because TX its for copper link and FX for fiber. [code]
View 5 Replies
View Related
Sep 21, 2012
I'm trying to upgrade some of the netwotk in my workplace.To do this I have istalled a 24port Catalyst 3560X switch.I'm looking to link it to my exsisting network via fibre.
I spoke to a local Cisco supplyer who recomended the above switch and an Allied Telesis Media converter.
I cannot seem to get the Allied Telesis unit to connect to the cisco switch.I have proved the fibre link by connecting 2 AT Media converters over the fibre.Do I have to enable something on the Catalyst switch or is the AT Media converter not compatible with the Catalyst switch?
View 3 Replies
View Related
Jan 2, 2012
I am doing an small project, I have to connect 4 cisco switches SF 302-08 (1 GBIC each one) to a core switch SGE 2000 (4 GBICs). Because of cable length I have go connect all 5 switches with fiber. The fiber termination is multimode LC duplex. My confusion is on the mini GBICs. There is compatibilities issues i been reading. [code]
View 3 Replies
View Related
Feb 14, 2013
We have a scenario where we want to connect 14 access layer 2950 switches to Core switch 3750 via optical fiber in a LAN.What model of 3750 Switch should we use to tackle this situation.I have learnt that WS-C3750X-24P should support it.Isnt it?
Can we use optical fiber SFP module to connect 2950 switches to core switch?Does Cisco 2950 Switch support optical fiber sfp module?
View 2 Replies
View Related
May 25, 2013
I need to connect 4 Floor Building with 4 Cisco 2960 - 48 ports switch each other and it needs to be through a fiber. So all PCs connected to each switch would reach the LAN/WAN from the other switch. (attached is the image here with)
I see that the 2960 has 2 SFP ports each port of each switch should connect each other or how?
My simple question is:
1. What cable / patch code I have to use = Single-mode or Multimode? ( distance for each switch will not more then 25 mts)
2. Do I have to use SFP or SFP+ module?
3. What kind of SFP/SFP+ module I have to use = Single-mode or Multimode?
4. What kind of connector should patch code have = LC / SC or ?
5. How to connect each switch with redundancy like ...each switch should be interconnected with each other or I have to choose Cisco 3750G which has more then 2 SFP ports (option#1 & opetion#2 = attached here with) =
Best practice for connecting cisco switches over fiber.
View 10 Replies
View Related
Apr 2, 2013
I have a 6500 connected to 3750 using fiber connection using patch panel.on the gig port of the 6500 give of error in Input errors, CRC and FRAME.There is no error from the 3750 gigport.
View 6 Replies
View Related
Apr 27, 2013
I have the following connectivity :Nexus(7004) - M1 8Port card with x2-10GB-SR <----------------------> 6509 -- 6704 card -- xenpak-10GB-SR ,The fiber link is not coming up.
View 4 Replies
View Related
Oct 23, 2012
I want to connect two linksys SRW2048 through fiber optic.. it's located different rooms with fiber optic....Is it possible through VALN....This setup using for CCTV connectivity?
View 1 Replies
View Related
Apr 24, 2012
I was checking some things on my Cisco 4500 and spot checking some of the ports. Using CNA it says it is at 10. The web browser to the switch says Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000-TX on port 6i/18 The CNA says, so what would cause the difference?
View 3 Replies
View Related
Jun 18, 2012
We would like to setup a link to our DR site that is separate from our main network traffic. This link will be used by an EMC VNX SAN for replication traffic. The SAN will be plugged into a fiber port on a 3750 switch and going out from the same switch (going in as multimode, going out as single mode) into a patch panel that runs over to the DR site (about a mile away). At the DR site it will go from the fiber panel into another 3750 switch which ends up going back out of that switch into our DR SAN.
I'm wondering what the best way would be to configure the fiber ports to accomplish this. I'm affraid that the replication traffic will find it's way over through another route and congest our main network unless configured appropriately.
View 4 Replies
View Related
Nov 5, 2012
We have Fiber link down down from both ends. From switch A goes to fiber box then to other fiber box then to switch B.
Switch A
Model: WS-X4418-GB-Gbic
Type: 1000BaseSX
Switch B
Model: WS-C3750G-24TS-1U
Type: 1000BaseSX SFP
Both sides are configured as trunk .
View 9 Replies
View Related
Mar 5, 2012
I'm looking for switches that support single mode fiber connections and would like to know if "WS-C3750-FS-S Catalyst 3750 24 100BaseFX + 2 SFP" and "WS-C3750G-12S-S Catalyst 3750 12 SFP" can serve the purpose?
View 6 Replies
View Related
Nov 20, 2011
We have Cisco 3524XL switch, Motorola AXS1800 chassis. I am configuring this cisco switch so I can connect AXS1800 traffic thru cisco 3524XL, on switch port gigabit 0/1, I am using cisco Part no. WS-G5486 (1000Base-LX) connector to connect to AXS1800, both port are member of vlan 200 allowed, and configured dhcp-server 192.168.0.1, but still I can't ping any host or host can't get DHCP server.
View 2 Replies
View Related
Jul 18, 2012
The module WS-X4306, support fibber fiber single mode ó fiber multi mode? what GBIC is for fiber single mode or fiber multi mode?
View 1 Replies
View Related
