Uhg. I deployed a 3560G a week ago and it was crashing... so I replaced it Sep 7 around 16:00 and now this one is crashing. Different logs.
Version 12.2(55)EX3
Sep 6 18:06:08: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 6 21:05:18: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 7 04:12:43: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 7 05:35:09: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 7 08:21:37: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 7 11:13:18: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Replacement Version 12.2(55)EX2
Sep 7 16:34:48: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 8 03:39:38: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 8 18:26:06: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 9 18:14:38: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
More detailed syslogs are in the attaced 'crash-logs.txt' file.
The device is running OSPF (it is in an NSSA). I have several other devices configured almost the same running the same IOS in my network and they are working fine.This does make the third out-of-box 3560C Cisco that has failed on me within a few days.
I have a number of 3560CG-8PC-S switches. My intention for them is to act as kind of gateway L3 switches - one for each satellite site. My thinking was simply to have an L3 device at the gateway to each of those sites so that any inter-vlan traffic within each site can stay within the site rather than having to traverse the relatively slow radio links to get back to the 3750X stack in the core. They are also, however, going to be directly serving client devices
My issue is that for some reason, when connecting a new device (laptop etc) to one of the access ports on the 3560's, the port behaves as if it's being blocked. No DHCP addresses go through, the indicator remains orange, and the clients have no connectivity. However, if I wipe the config, I get a VLAN 1 IP address for my client no problems at all. And to make matters more confusing, only two out of my four 3560's are doing this. The other two have exactly the same config, but work perfectly.To that end, I'm loading the config below. I've followed that by the show running-config output, and show ip interface brief outputs.
I got some specs here that I can't seem to match with any existing switch - unless the 350CG-8PC-S can be powered by PoE.Let me quickly put down the important specs.
8x Gigabit ports 2x 1G Copper or 1G SFP Uplinks (It'll be a 1x Copper and 1x SFP setup) support for PoE passthrough ( so just capable of it, provided it's 2x Copper Uplinks )
When will Cisco release the IOS release 15 for Catalyst 3560CG? We need it because of the critical voice feature (authentication event server dead action authorize voice) for 802.1x.
Actually only release 12.2(55)EX3 is available for the 3560CG-8PC-S models. The funny part is that for older 3560-12PC-S models there is release 15 already available.
I tried to put QoS in a WS-C3560CG-8TC-S version 12.2(55)EX2.It shows 0 traffic in class-map. Here is the config My question is why I can not see the traffic via class-map?it should in the default Q if incorrect mark.I erased the config and config with the autoQoS, shows the same result.
class-map match-any VoIP description Voice IP Phone RTPmatch access-group 157 class-map match-any WEB description Internal Web, SSL Web, DNS query, Pinnaclematch access-group 153 ! policy-map QOSMARK class VoIP set dscp ef class WEB set dscp cs3 class class-default set dscp default
I am facing with Cisco 3560CG Switch. We have a Cisco WS-C3560CG-8PC-S (Cisco Catalyst 3560-C Switch, 8 GE PoE, 2 dual-purpose uplinks, IP Base image) switch which will be a core switch and the internet link from the ISP is terminated on a Modem. The ISP configured the internet modem and provided the details such as Gateway IP, Subnet Mask, DNS IP address, Usable IP Address Block, to configure the switch, where ew have connacted the Modem. When, I verified the details, there were only 4 IP addresses available under Usable IP address block. Spoke with the ISP and they confirmed that they cannot increase the IP Addresses (some limitation on the Modem) in the pool and we have to do NATing at the switching (Which we can't do, because of IP Base image limitation). About the network, it will be a flat network with only one VLAN which is used for Wireless Guest Access.
One of our edge router (6500, running ios 12.2(33)SXJ) crashed with the following error. I found there were some RP-SP-ping GOLD test skipped due to high SP CPU utilization, but dont know if thats the reason. Crashinfo is attached. Hope to get you expert opinion on this. Shall we go for upgrade ?
Feb 17 15:19:10: %C6K_PLATFORM-2-PEER_RESET: RP is being reset by the SP %Software-forced reload 15:19:10 met Sun Feb 17 2013: Breakpoint exception, CPU signal 23, PC = 0x42E24578
I have a situation. I am running two-switch 3750-stack and it crashed this morning. IOS version the switches is: "flash:c3750-ipservicesk9-mz.150-1.SE.bin"
SRPRSRGBYA#
Log Buffer (10000 bytes): 3:40.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan104, changed state to up Nov 3 13:13:40.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan201, changed state to up Nov 3 13:13:40.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan202, changed state to up M-1-CRASHED: (SRPRSRGBYA-1) Nov 3 13:18:13.336: %PLATFORM-1-CRASH(code)
I am trying to bridge the traffic(including different vlan traffic) from rtrA to rtrB using "bridge-group" functionality.I achived the same using a 7200 using the below configuration. [code] When I tried the same using 7600 router ping failed between rtrA and rtrB. Then from the documents it seems "bridge irb" is not supported in 7600.Is there any other way we can achieve the same fuctionality ( eg: using switchport also fine) ?
I´m looking for an IOS on a 7609 SUP720/MSF3 that supports the NAT-PT feature (IPv4 to IPv6 translation). I searched on the Cisco Feature Navigator but the tool didn´t show up any IOS for the 760x platforms. I only got the feature "NAT-PT: Support for Overload (PAT)" with IOS 15.xS train.
3750 Stack (Voice gateway for phones configured on the 3750 and has a VPC nexus) + + + + + + (Nexus5596) ++++++++++ (Nexus5596) (Gateway for all other vlan like PC / servers / etc) + + + + + + 3750x access layer (VPC to Nexus) [CODE].....
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102 Autobooting specified file using Variable BOOT ..... Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
I got the error in object when I try to add a new HSRP group in new vlan.All the HSRP group has the same HSRP group the 2.another way to provide clients's default gateway redundancy for each Vlan intead to use the HSRP?
I am having problems with IGMP and QoS on CAT6500 platform with SUP720 engine.The problem is, it seems that all IGMP packets are getting marked with DSCP 48 when sent out of the switch regardless of any input service policy. I found several articles saying that PFC QoS does not apply to IGMP packets. However in IOS 15 that should be possible, but I didn't get it to work there either. [code]
we observe that the process platform causes about 50% cpu load of our Nexus 7010.Could not find any information for what this process is responsible to find out the root cause of the high cpu load.
I know that an ELAM can be setup on a 6500 running ipservices 12.2(33)SXJ, however I noticed that following commands are not available on a 6500 router running advipservices 12.2(33)SXJ:show platform capture elam asic etc
So I wanted to know if there is an alternate way to setup an ELAM for troubleshooting purposes?
We have 2 x C6506E and 2 x C3560-48's, they are all interconnected via port channels at 2Gb per channel. The 6506's are running CEF but the 3560's are not (The 3560's carry all our server traffic).When I do a show CEF on the 3560's it says %IPv4 CEF not running. There does not appear to be a global command to enable CEF on these switches.Is this an IOS version option or is not supported on the hardware platform?
In our environment we have some HP chassis, and with them there are blade switches. Lately, we've been seeing some drops on few servers connected on the blade switch ports. The switch model is WS-CBS3120X-S. And below is the tx drop for two interfaces ( where the servers are connected to).
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
Previously posted as C2900 - inward NAT partial success...
Running C2900-UNIVERSALK8-M, Version 15.0(1)M3 RELEASE SOFTWARE (fc2)
I have several sets of inward NAT defined (51001-51007, 52001-52007. 53001-53007),all to various internal addresses. When I attempted to add another set, the new onesdo not work and get a "timeout" error.
When I tried port 51008, it gets a timeout. When I changed 51008 to 51010, the 51010 now gets a timeout, and 51008 now gets "connection refused" (which I expect).The original sets all work, the new ones (added at the end of the lists) do not.When I am on any of the internal machines, the target (192.168.1.21) works fine.When I am "in the router", I can connect via the ssh command, so I know that therouter can talk to 192.168.1.21 on port 22 as expected.
We are attempting to PXE boot from clients obtaining their DHCP lease information from DHCP pools configured on our 4506. The PXE server, and the client are configured in separate VLANs. We have configured option 66 to point to the PXE server IP address, and the bootfile option to point to the PXE boot configuration filename. On the client side SVI, we also have configured the ip helper-address command to point to the PXE server (which also acts as another DHCP server for redundancy).
The PXE boot continuously fails stating it is unable to find the configuration file. If we remove the DHCP pool from the 4506, and allow the client to receive their DHCP lease info from the secondary server (Windows 2k8 - same server as PXE server), they PXE boot with no issues.
We have no problem obtaining DHCP info, just completion of the PXE process.
We have an issue where switches are failing weekly in a switch closet. In the past month we have gone through several 3750G switches and a couple 4510s. The power supplies have eventually made a popping noise and had to be replaced. on the 4510s we've tried two chassis and gone through several power supplies.The switches have been behind UPS systems so should be receiving conditioned power.Could load from the PoE devices really be causing this? I wouldn't think it's power since they are behind a UPS.
i have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
today I witnessed a cisco n5k that stopped playing fair. For a yet unkown reason several interfaces started to show output errors all begining within the same second. While i instantly thought this would be a wiring issue I began to ask myself what an output error actually means. Google usually brings up output drops, not regular output errors. So what is it and how can a 10G fiber interface even detect that there is a problem without receiving what it was sending?
I've just noticed an error I've never seen before in our switch logs. We have a stack of 6 Cat3750G-48TS-E switches. The first two in the stack have been up for just over a year and I've only just noticed this error. Thus far, I haven't noticed any symptoms - I just stumbled upon this error while checking for something else.
As far as I can tell, this has only popped up once and it was 2 days ago. Unfortunately, due to an incorrect firewall rule, our syslogs were not getting to our syslog server so I don't have any historical logs to check against, but it hasn't happened since.
The error I've seen is as follows:-
Jun 5 17:04:03.288: * ManagementInterfaceInitialized exception in port-asic 0 (N16FujitsuSwitch.com.au-2) Jun 5 17:04:03.288: ***********************************************************
We have just under 500 switches in production (various models but for this discussion we'll stick with 3750's). All are currently running tar IOS (web based). We want to upgrade the IOS from c3750-ipbasek9-tar.122-55.SE1.tar to.122-55.SE5 but some of our switches do not have enough flash to upgrade successfully. We use CiscoWorks to distribute our software upgrades. I know you can lower the flash requirements on the IOS in CiscoWorks, which I have done (changed from 16Mb down to 12Mb) and the upgrade still fails.
1) How far can I lower the flash installation requirements in Ciscoworks and what are the ramifications?
2) If we decide to change from the tar IOS version to the bin IOS version because we don't even use the web based features anyway, is there an easy way to do this? (CiscoWorks will not upgrade an image from tar to bin)
