When will Cisco release the IOS release 15 for Catalyst 3560CG? We need it because of the critical voice feature (authentication event server dead action authorize voice) for 802.1x.
Actually only release 12.2(55)EX3 is available for the 3560CG-8PC-S models. The funny part is that for older 3560-12PC-S models there is release 15 already available.
We have a catalyst 2950 switch running:
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)
This release doesnt have the snmp-server enable traps errdisable command.
Where to look on the cisco site for the next available release for me that would have this command in place?
I got some specs here that I can't seem to match with any existing switch - unless the 350CG-8PC-S can be powered by PoE.Let me quickly put down the important specs.
8x Gigabit ports
2x 1G Copper or 1G SFP Uplinks (It'll be a 1x Copper and 1x SFP setup)
support for PoE passthrough ( so just capable of it, provided it's 2x Copper Uplinks )
Does that match the 350CG-8PC-S ?
I tried to put QoS in a WS-C3560CG-8TC-S version 12.2(55)EX2.It shows 0 traffic in class-map. Here is the config My question is why I can not see the traffic via class-map?it should in the default Q if incorrect mark.I erased the config and config with the autoQoS, shows the same result.
class-map match-any VoIP description Voice IP Phone RTPmatch access-group 157
class-map match-any WEB description Internal Web, SSL Web, DNS query, Pinnaclematch access-group 153
!
policy-map QOSMARK
class VoIP set dscp ef
class WEB set dscp cs3
class class-default set dscp default
[code].....
I have a number of 3560CG-8PC-S switches. My intention for them is to act as kind of gateway L3 switches - one for each satellite site. My thinking was simply to have an L3 device at the gateway to each of those sites so that any inter-vlan traffic within each site can stay within the site rather than having to traverse the relatively slow radio links to get back to the 3750X stack in the core. They are also, however, going to be directly serving client devices
My issue is that for some reason, when connecting a new device (laptop etc) to one of the access ports on the 3560's, the port behaves as if it's being blocked. No DHCP addresses go through, the indicator remains orange, and the clients have no connectivity. However, if I wipe the config, I get a VLAN 1 IP address for my client no problems at all. And to make matters more confusing, only two out of my four 3560's are doing this. The other two have exactly the same config, but work perfectly.To that end, I'm loading the config below. I've followed that by the show running-config output, and show ip interface brief outputs.
configure terminal
hostname ASW34
!
enable secret *RuT1l3&
service password-encryption
username xxxx password xxxx
[code].....
I am facing with Cisco 3560CG Switch. We have a Cisco WS-C3560CG-8PC-S (Cisco Catalyst 3560-C Switch, 8 GE PoE, 2 dual-purpose uplinks, IP Base image) switch which will be a core switch and the internet link from the ISP is terminated on a Modem. The ISP configured the internet modem and provided the details such as Gateway IP, Subnet Mask, DNS IP address, Usable IP Address Block, to configure the switch, where ew have connacted the Modem. When, I verified the details, there were only 4 IP addresses available under Usable IP address block. Spoke with the ISP and they confirmed that they cannot increase the IP Addresses (some limitation on the Modem) in the pool and we have to do NATing at the switching (Which we can't do, because of IP Base image limitation). About the network, it will be a flat network with only one VLAN which is used for Wireless Guest Access.
View 1 Replies View RelatedUhg. I deployed a 3560G a week ago and it was crashing... so I replaced it Sep 7 around 16:00 and now this one is crashing. Different logs.
Version 12.2(55)EX3
Sep 6 18:06:08: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 6 21:05:18: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 7 04:12:43: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 7 05:35:09: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 7 08:21:37: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 7 11:13:18: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Replacement Version 12.2(55)EX2
Sep 7 16:34:48: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
Sep 8 03:39:38: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 8 18:26:06: %PLATFORM-1-CRASHED: Data TLB Miss Exception (0x1100)!
Sep 9 18:14:38: %PLATFORM-1-CRASHED: Debug Exception (Could be NULL pointer dereference) Exception (0x2000)!
More detailed syslogs are in the attaced 'crash-logs.txt' file.
The device is running OSPF (it is in an NSSA). I have several other devices configured almost the same running the same IOS in my network and they are working fine.This does make the third out-of-box 3560C Cisco that has failed on me within a few days.
i created the 10 V LAN in my Cisco 3750 switch.All other V LAN DHCP IP's (192.168.2.X - 192.168.10.X) will be release from the DHCP server except VLAN1 . In my 3750 switch i created DHCP pool(192.168.14.X).... and i assigned to VLAN10.... but one of the client is assigned to V LAN 2(192.168.2.X) configuration. but its getting IP from the Cisco DHCP instead of DHCP server.
View 2 Replies View RelatedI would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies View RelatedI have the network described below, on which I am running PIM.
(network) ---- Embedded Linux Router --(vlan 5)-- CAT 3560G --(vlan 5)-- Cisco 1811 Router ---- Multicast Listener
The Linux Router and the 1811 have formed a PIM neighbor relationship. The multicast listener sends an IGMP Join and I can see the PIM join leave the 1811 router (via "debug ip pim"). Using tcpdump on my linux router I never see the Join come in, but I can see the PIM Hellos (which is why the neighbor relationship formed).
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View RelatedI have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies View RelatedDoes Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedI have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedWe have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
I have peculiar challenge ahead of me and would like to get new perspectives.
The objective is to route specific VLAN traffic and the caveat is that I have multiple VLANs with the same network address.
For example:
VLAN100 10.10.10.0/28 VLAN101 10.10.11.0/28 VLAN102 10.10.12.0/28
VLAN103 10.10.12.0/28
VLAN104 10.10.11.0/28
I need traffic going from VLAN100 with a destination of 10.10.11.0 forwarded to VLAN101 and NOT VLAN104.
This task is currently being completed by a multi context firewall and we're trying to decommission the asset.
I have a 2504 WLC connected to a Catalyst 3560 which has multiple vlans and is connected to a 2800 series router. I know the catalyst is L3 but I am needing nat functions to get outside to the internet. From my 2800 series router I am able to ping out to the internet, also I am able to ping the vlan interfaces on the catalyst switch. Problem is from the catalyst switch I can ping the inside and outside address of the 2800 but I cannot get any further then that. I cannot ping the 2800 router gateway. Not sure what I am doing wrong as far as routing.
I've attached my 2800 and 3560 configs.
We have a IP-phone system connected to port 1 on a 3560 switch, the phone system tags traffic with dscp. The switch uplink is on port 24.
Is this configuration correct:
interface 1:
auto qos trust
interface 24:
priority-queue out
Are there any best practices for preventative maintenance on Catalyst Chassis switches. Looking to build a PMI schedule for a customer. Or is there evidence not to perform it at all. Things like re-seating line cards, cleaning fan exhausts, etc.
View 1 Replies View RelatedDoes the Catalyst 3560 support GRE ?
I know that Catalyst 3750X support GRE ,but Catalyst 3750X cannot work in hardware it.
Does the Catalyst 3560 cannot work in hardware too?
i have a cisco catalyst 2960g and for some reason out of the blue, some interfaces go down and then up. It started doing it after a power cycle.
View 1 Replies View RelatedI've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies View RelatedI'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
View 1 Replies View RelatedI am trying to setup the WOL for our enterprise. We have a C4500 setup with mutliple Vlans. We are using Microsoft SCCM server to wake up workstations for security update. The workstations are on vlan190 and the Microsoft server is on vlan 441
Here's my config
the config below
interface Vlan190ip directed-broadcast 100 (Enables the translation of a directed broadcast to physical broadcasts)
access-list 100 remark ====== Wake-On-LAN ======no access-list 100 permit udp host 10.4.40.98 any eq 9 logaccess-list 100 remark ====== End of ACL 100 ======
[Code].....
have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot the master switch in the stack, the master switch change to another switch, then I can telnet/ssh to this switch. I check the Ciscoworks server syslog report, there are many MAC address flapping error message, and I beleive the MAC address flapping occured before several weeks. ( the G2/0/15 & G3/0/15 is connect to a VMware ESX server and the EtherChannel config mismatch with this Catalyst 3750 switch ) How to mention the root cause of the "low on memory" problem and what is the abnormal memory usage ( free memory percentage below ?% )?
View 5 Replies View Relatedmy Catalyst 3750 switch. Following a power cut the switch no longer boots up. The SYST light flashed green but no POST checks are made. I cannot see any boot messages from the console port either. The switch was on a UPS but some thing may have damaged the switch.
View 7 Replies View RelatedI have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
I am trying to find out what the most upto date IOS I can put in my Cisco Catalyst 3500 XL switch, and I'm not sure if this the newest software. I have a lab setup at my house to study for the CCNP certs and this IOS doesn't have all the commands I need, well it might but all depracated commands.
View 5 Replies View RelatedThere is a requirement to configure tacacs and radius on catalyst 3750X (version 15.0) where two vrf exist.Is therer a solution to configure "tacacs-server,host x.x.x.x vrf yyy" ?? I know it is possible to configure under the "aaa group server radius xxx" the command "ip vrf forwarding yyy".Is there anything else for the tacacs-server and radius-server command?
View 2 Replies View RelatedDoes SUP 7E is comatible with IOS? It came with IOS-XE preloaded and there are no IOS software listed under downloads.
View 3 Replies View Related