Cisco WAN :: Adding IPSec To 1941 Router?
Jan 17, 2013I need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Router 1941 But Can't Do Ipsec
Oct 10, 2012I did have a router cisco 1941 but can not do ipsec with it,i did take a smart net.
View 3 Replies View RelatedCisco WAN :: Adding 3rd T1 To 1941 For More Bandwidth
Aug 15, 2012We have a Cisco 1941 Router with two single HWIC cards supporting two T1 lines 3Mbps total bandwidth. We have a distance learning lab that takes atleast 2mb connection when in use so it realy kills our bandwidth. I was looking to possible add a thrid T1.
My question: Can I just buy a double wide HWIC card and replace the single port one. Would this require re-configuration or it's simply plug n play?
What other options can I try for more bandwidth instead of adding thrid T1.
Cisco WAN :: 1941 Router - Enable IPSec Virtual Tunnel Interface With Tunnel Mode IPv4
Sep 23, 2012I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies View RelatedCisco VPN :: 1941 Disappearing IPsec Routes With RRI
Aug 26, 2012I am trying to set up a pair of 1941 routers in a HA configuration to act as L2L VPN gateways. The active router of the pair should distribute routes to the remote destinations using OSPF to internal routers. The VPN part is working fine and the routers are correctly advertising routes to internal hosts, however my problem is that when an IPsec sessions disconnect, the routes disappear and therefore internal hosts cannot reestablish a connection. If the remote end establishes a connection, the routes appear again and connectivity is restored.
My setup is as follows: (ASA) --> (pvpn01 & pvpn02 HA pair) --> (internet) --> (remote peer)
The other router in the pair has exactly the same config except with different interface IPs. The remote end is configured to talk to the HA address
91.216.255.248.The VPN routers are both running IOS version 15.0(1r)M9.
When I initially boot the routers, the route for 192.168.66.0/24 appears in 'show crypto route', and is advertised to neighboring routers. If I ping an address on that network an SA is established and stays active as long as there is traffic flowing. pvpn02#show crypto route
If I then stop traffic flowing over the tunnel and wait until the IPsec SA lifetime is expired, the route is deleted from the system routing table and therefore not distributed by OSPF. The result is that internal hosts cannot reestablish the tunnel as the other routers have no route to the 192.168.66.0/24 network.
Is this a bug, or is there another way to get the RRI routes to persist on the active router?
Cisco WAN :: 1941 - Multiple VRF BGP / GRE / IPsec Failing
May 17, 2011I'm trying to configure a Cisco 1941 to connect to multiple Amazon VPC instances. Each VPC instance brings up 2 x IPsec over GRE tunnels with BGP in to the EC2 cloud and enables flat extension of the corporate LAN. Basically. you can spin up EC2 instances in a private subnet and route to them across the VPC link from the corporate LAN.
The Amazon configuration is templated and not designed to support multiple instances on one customer access gateway - however, I want to overcome this and find a technical solution around bringing up a second physical router. I've got VRF configured and working for the first instance, but when we add a second VRF to the configuration IPsec fails. The second VRF is essentially identical to the first.
We're potentially looking at a licensing issue with IOS 15.x, the version we're running is...
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
data None None None
[Code]....
However, the IPsec configuration is complete and all keychains etc. are in place as they should be.
Cisco Security :: 1941 - Unable To IPsec
Oct 10, 2012I did purchase a router 1941 universal k9 but i can not do ipsec on it, i took a smart net for that router in order to have or download ipsec on it.
View 1 Replies View RelatedCisco WAN :: 1941 ADSL Fail Over To 3G HWIC With IPSEC VPN
Jul 23, 2012The setup is a S2S VPN with failover to 3G HWIC in a Cisco 1941 however the IPSEC tunnel needs to remain up through 3G if ADSL fails.The failover works ok, however when plugging ADSL back in, the - "sh crypto session" shows both dialer 0, and dialer 1 with the crypto map session to the other side of the VPN and either side is now not pingable.The NoIP DDNS updater client runs on a server in the network and all IP resolution to host1,host2 works ok (other side of VPN is Cisco 1921 with ADSL HWIC and 3G HWIC). [code]
View 5 Replies View RelatedCisco Switching/Routing :: 1941 / IPSec Tunnel Up No Traffic?
Mar 7, 2013I have an IPSec tunnel configured on my Cisco 1941. The other device is an ZyXEL router.I can see the tunnel is up but there is no traffic.This comes out the show crypto ipsec sa
interface: Dialer1
Crypto map tag: CMAP_AVW, local addr 10.10.10.89
protected vrf: (none)
local ident (addr/mask/prot/port): (192.168.200.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.150.0/255.255.255.0/0/0)
current_peer 20.20.20.161 port 500
[code]....
Cisco Switching/Routing :: 1941 / K9 Unable To Ping Over Site To Site IPSEC
Jul 12, 2012I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedCisco VPN :: PAK To Activate VPN On 1941 K9 Router
Jul 1, 2012We bought a CISCO1941 K9 router. To enabled IPSec feature, I need the PAK to active IPSec on 1941. Where I can buy a valid PAK? Could it be done via on-line support?
View 5 Replies View RelatedCisco VPN :: Activating SSL On 1941 Router?
Mar 23, 2011I have got a Cisco 1941 router and would like to activate my SSL VPN license on it. How do i go about it?
View 6 Replies View RelatedCisco WAN :: What Is The Processor Available In 1941 Router
Jan 31, 2012What is the processor available in cisco 1941 router? is it RISC?
View 4 Replies View RelatedCisco VPN :: How To Configure SSL VPN On 1941 Router
Mar 22, 2011How do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies View RelatedCisco WAN :: Cannot Log Into 1941 Router To Setup
Mar 28, 2011We purchased this router with the cisco IOS software installed. I've installed the Vista driver on my win 7 box. I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.
View 3 Replies View RelatedCisco WAN :: 1941 Choose Router For VPN And Eigrp
Feb 16, 2013We have software router vyatta and about 15 branches with cisco 881w and cisco 1941. All branches have 10mbs bandwidth and 3 of them have 50mbs. Link to vyatta has 100mbs bandwidth and situated in datacenter.All branches connect to vyatta via vpn site-to-site with ipsec.I want to change vyatta to cisco router or asa.
View 7 Replies View RelatedCisco WAN :: How To Break 1941 Router Password
Jun 16, 2010i have cisco 1941 router.unfortunately i dont remember password.Can any body tell me how to break password.I tried to go in Rom mon using ctr+break but nothing is happened.
View 5 Replies View RelatedCisco WAN :: 1941 Router ATM Interface Went Down While Applying QoS?
Sep 28, 2011c1900-universalk9-mz.150-1.M4.3
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*0 CISCO1941/K9 FCZ1510C50V
Technology Package License Information for Module:'c1900'
----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
[code].....
Cisco WAN :: Load Balancing In Router 1941?
Nov 28, 2012i have cisco 1941 router with HWIC-4EWS Card We have two ISP, how to configure the load balancing
View 3 Replies View RelatedCisco WAN :: 1941/K9 Router Configuration For Internet?
Dec 22, 2010We configured 1941 k9 router for inernet purpose
ip name-server 218.248.255.146ip name-server 218.248.255.212multilink bundle-name authenticated!!!license udi pid CISCO1941/K9 sn FHK144773MG!!interface GigabitEthernet0/0 ip address x.x.x.x 255.255.255.248 ip nat outside ip virtual-
[Code]....
when i configured access-list 2 permit any . Internet working on local systems but we are not able to connect telnet.
Cisco WAN :: Bundling 2 Gigabitethernet In 1941 Router
Apr 7, 2011I am using cisco 1941 router in my DC for Internet service. I am going to terminate 2 WAN links each 4 mbps to my Gigabiethernet ports. Is bundling is possible to enjoy full 8 mbps internet to my organisation?
View 5 Replies View RelatedCisco WAN :: 1941 Router - CP Express Not Working After Upgrade
Aug 13, 2011I am trying to upgrade CP Express to 2.5 and after the upgrade I bring up the webpage to login and I am prompted for my credentials, I enter them and I am authenticated. However the CP Express home page never loads. I have tried to reload 2.0 but it does the same thing.
View 3 Replies View RelatedCisco Switching/Routing :: 1941 Router Cannot Get To Internet From PC On LAN
Mar 12, 2012I am having an issue accessing the internet from a PC on the LAN. I have configured the PC with the gateway of the router infront of the ISP to test. I can ping from the router to google or any other internet IP. From the PC I can ping to the GIG0/1 (Inside LAN IP) and the GIG0/0 (Outside WAN IP going to ISP) but I can't ping the Next Hop IP of the ISP or anything past that. If I do a trace route from the PC to the google IP address it hits the GIG0/1 Inside LAN IP Address but fails from there. Here is a cut down snap shot of the router configure
[code]....
Cisco Switching/Routing :: Setting Up VPN For 1941 Router?
Sep 6, 2012im having trouble setting up a vpn for a 1941 router this is what I have setup
crypto isakmp policy 10
encr aes 256
authentication pre-share
crypto isakmp key ########## address 63.247.48.50
[code]....
my whole problem comes about when i need to Nat 192.168.1.0 to 10.12.14.0/24 before it goes through the tunnel.
Cisco WAN :: Configure 1941 Router For PPPOE With Dynamic IP?
Dec 18, 2010how to configure the Cisco 1941 router for PPPOE with dynamic IP
View 10 Replies View RelatedCisco WAN :: 1941 - Speed Slow After Connecting To Router
Apr 6, 2013In my company bought 20 mbps lease line(ISP Line).I connect directly with my laptop and after checking it show 20 mpbs speed.If i connect cisco 1941 router and configure PAT and Its working fine but I check with speed I connect directly to another interface on my router to laptop at that it show only 8 mpbs speed.I am check with ISP person but they told its not an issue in ISP because we connect directly it show perfectly 20 mbps speed but connecting with your router at that time it show 8 mbps speed,so problem with your router configuration.
View 4 Replies View RelatedCisco WAN :: Plug HWIC-1FE On 1941 Router Running?
Feb 26, 2013I want to know if I can plug a HWIC-1F on a cisco 1941 router without shut it down?
View 1 Replies View RelatedCisco VPN :: Change Country Code On 1941 Router
May 3, 2011I am trying to install SSL VPN on our 1941 router. When i try to send a CSR for signing the site complains about the country code not being correct. How can i change the contry code in Cisco IOS Version 15.0(1r)M9 ?
It is also complaining about the domainname, but the thing right now is the contry code.
Cisco WAN :: 1941 Router With PPPoE ADSL Conflict
May 3, 2013I m getting the below debug log and can not get IP from my ISP. It is static IP address and there is modem in bridge mode for the adsl line.
Below Conf and debug out put,interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
end
[Code]....
Cisco WAN :: 1941 - Small Router And LTE 4g Connection / Information
Jan 18, 2011Is there any small router model (like 1941) that can be ready for future 4G LTE?
View 1 Replies View RelatedCisco WAN :: Will 1941 Router Support USB Cellular Data
Jan 9, 2011The 1941 router has USB ports, Will it support a USB celluar data card?
View 5 Replies View RelatedCisco Switching/Routing :: 1941 Router Does Not Keep Config When Turned Off?
Aug 22, 2012I have a 1941 integrated services router that will not keep the configs. After several atempts of saving running config to the startup config, then rebooting the device. I am having to reload the configs manually from TFTP because they are gone. I have also tryed the "wr" command to see. Is there a proper way to shutdown this particular type of router?
View 2 Replies View RelatedCisco WAN :: 1941 Router Not Pass Traffic From Window 7 Computers
Jul 14, 2011I cannot telent to 1941 router from a Window 7 PC and I can a Window XP PC. Telnet is enabled on Win 7 PC. I upgraded 1941 to latest IOS.Compters running Windows XP can telnet to router and hit the internet. Computers running Windows 7 cannot hit the internet. I replaced the 1941 with a 1760 router and Win 7 computers can telnet to router and hit the internet. I used the same config from the 1941 on the 1760.
View 5 Replies View Related