I am trying to configure Crypto PKI in ciscio 2911, Once i configured the root certificate for the router , i can see the validity date wrongly but the same certificate is fine in the other devices . [code]e when i am trying to configure the local certificate.
View 1 RepliesI am currently getting a strange error when trying to use and crypto services on our ASA 5520 (8.0.3)Initially I observed that a connected VPN had dropped.Then when I attempted to use ASDM or SSH I was blocked.
In the end I opened telnet as a test and this was successful. Syslog also shows that traffic is passing as normal.The only obvious error I can see when observing various debug traces is this;
FW02# CTM: rsa session with no priority allocated @ 0xCF1FBBA0
CTM: Session 0xCF1FBBA0 uses a nlite (Nitrox Lite) as its hardware engine
CTM: rsa context allocated for session 0xCF1FBBA0
CTM: rsa session with no priority allocated @ 0xCE7A5EA8
[code]....
I configuring QoS policing in a Cisco 2911 in a 128K/256/512 link, but when I apply the configuration in interface I receive the error below:
Configured Percent results in out of range kbps.Allowed range is 8-2000000. The present CIR value is 6.
Current configuration : 191 bytes
!
interface GigabitEthernet0/1
description ***V-SAT***
bandwidth 128
[Code].....
I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
Here is the document I was referencing
[URL]
I have configured Priority Queueing in my Cisco 2911 Router. I have set queue list high, medium, normal and Low. But when I put show interface gi0/2, it is showing the queueing strategy is priority queueing but it is not showing the (size/max/drops) values.
View 1 Replies View RelatedI am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
I have a 2911 router where I was configuring the device to allow remote desktops connections. Everything is working properly, but for some reason my ACL has disappeared.
View 5 Replies View RelatedPurchased a 2911 router for a customer, and I'm sure I'm missing a module here.
Teleco installed T1 and left connection to smart jack. Router only has 2-3 copper ports.
Can I get away with configuring the blackbox with RJ45 to the copper port on the router ethernet or do I need to purchase a HWIC ?
I get the following error:
Router#config t
Router(config)#snmp-server view rttmon ciscoRttMonMIB included
%Bad OID
The same command is accepted on a Cisco 2900 router
Router#show version
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
[Code]......
I have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
View 1 Replies View RelatedIf all you have is a high end cisco router available, can you plug in hosts to the router ports, and configure them within the same subnet? (When I try to configure ports within the same subnet, I receive a "same subnet" error.
View 3 Replies View RelatedI have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies View RelatedFirmware 1.3 introduced a DHCP server.
It seems that I can add a pool for any subnet except the 192.168.1.1/24. I have successfully added a pool for 192.168.0.1/24, 172.16.16.1/24, etc. But when I use the same commands to add a 192.168.1.1/24 pool, I get:
sw(config)#ip dhcp pool network Device sw(config-dhcp)#address low 192.168.1.20 high 192.168.1.250 255.255.255.0 Illegal IP addresses range or subnet configuration Trying to configure a network pool on default IP interface
VLAN 1 IP was changed from default 192.168.1.254 to a static of 192.168.0.1.
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
I have this situation, I need to establish an IP sec communication to another site but I need to identify all my packets sent, as a different networks as my local one. for example: my local network is 10.5.0.0/24 and I need to sent packets as 10.6.0.0/24. I suppose that I need to do Nat with this IPs. But in this router Nat is already applied to outbound traffic to Internet. How can I apply this NAT to crypto map only?
My router is a Cisco 877 with 12.4 IOS an this is the relevant configuration, crypto map vpn it´s used to sent traffic to second site.
crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxxxx address XX.XX.XX.XX
crypto ipsec transform-set vpn esp-3des esp-sha-hmac
crypto map vpn 1 ipsec-isakmp set peer XX.XX.XX.XX
[ code]....
I'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?
View 1 Replies View RelatedI have to connect one of our it labors with some ec2 instances in amazon vpc. I downloaded a configuration file from amazon which starts with the command
crypto isakmp policy 200
My router tells me that he does not know crypto isakmp.
I searched on the internet and found that i have to install a specific license, but unfortunately i cannot find which license i have to install.
The show license command show following licenses
AdvIpServices active
AdvSecurity active
advsecurity_npe, ios-ips-update, waas_Express no state displayed
ssl_vpn active but eula not accepted
I found that i can accept the eula license with license boot module c880-data technology-package SSL_VPN command
But this command is also not available on my device. getting the crypto isakmp command working?
I have a 2650XM 16mb flash, 64 mb ram. 12.2(12a). now I want to buy 12.4(25d) with crypto. How much is it? And where can I buy it ?
View 10 Replies View Relatedi have 2951 ISR but i cant configure encryption it have UniversalK9 IOS and i cant find any other ios that will support crypto map?
View 4 Replies View Relatedi have Cisco 1941 router with following IOS image:Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2) below mentioned commands are not working :
crypto isakmp policy 5
encr aes 256
authentication pre-share
group 2
what could the issue ? do i need to change the IOS image.
This setting is correct?
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 auto
[Code]...
I have a Cisco 881 ISR (CISCO881-SEC-K9) and have the advanced security license installed and enabled/active and in use (see screenshot). However, the isakmp crypto module is not available.
[code]....
I have applied a crypto map (fo ipsec vpn) on the dialer interface (for PPoE connection) in Cisco 2800; every time when the router restarts the crypto map is removed from the dialer interface even though i save the configuration every tim when i apply the map on the interface. Is there any way that the crypto map remains there on the dialer interface after the restart of router.
View 1 Replies View RelatedIn a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies View RelatedIn my test lab , I have a CISCO 1841 with a AIM-VPN/BPII-PLUS board , everything was working fine , until I would like to see the difference with and without the accelerator.Sins the moment that the IOS told me that he will change to SW accelerator instead of HW accelerator , I can not make it work anymore.I have a copy of the full working configuration before I did this , I have put it back on my router but still NO VPN. [code]
View 2 Replies View RelatedI have a network architecture like the one HERE but with alot more spokes (32). Would my cisco 3925 be able to support so many crypto maps?
View 2 Replies View RelatedNew to the forum and not much Cisco IOS experience let alone on the security side of things. I know how to navigate the IOS and can do basic switching and routing just fine. My company currently has a DMVPN setup w/ about 10 tunnels going back to the hub. We have 4 more sites they want me to setup and I keep getting stuck at the crypto maps. I have been reading about VPN's, DMVPN's , etc. for days now but can't find any examples of how we are configured. The priority of our crypto maps start at 65536 and go up. Default max is 65335 from what I have read, and I cannot assign a priority that high statically. [code]
View 3 Replies View RelatedI have a ASA 5510 that has something weird going on I have just added a base config where you can access on a inside interface but for some strange reason after I disconnect i have to ping inside interface first before I can connect via telnet or SSH and then regenerate therecrypto key
View 3 Replies View RelatedI ahve a requirement to configure static crypto for 1800 site and I need to configure on two sepaarte interfacs at spoke site which means I need to configure 1800*2 = 3600 peers at central site. The challenge I have is due to load balancing , the traffic dynamic crypto can not be used since traffic may be initiated from Dc on other link which may get dropped incase not encrypted.
View 5 Replies View RelatedI have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
I have a cisco 887 connected as temp measure to a 3g device via a fast0 port. all works fine. VPN comes up...but the moment i apply the crypto map to the vlan.. DHCP stops allocating ip address. I have remove irrelevant config ( dialer, atm etc as they not been used)
config below
p dhcp excluded-address 10.29.80.253 10.29.80.254
ip dhcp excluded-address 10.29.80.1 10.29.80.229
!
[Code]......
Just looking at a new clients setup and they have a ISAKMP vpn to the old security company I am trying to remove...I am fairly new to cisco, I actually know how to setup the ISAKMP policies, acl's etc but never had to completely remove one before All I can find is Clear Commands which seem to just flush the config not actually delete any of the policy etc...Its not that urgent as all passwords are changed on the domain and the cisco, the usernames have been deleted as well.
#show crypto isakmp peers
Peer: ** Port: 500 Local: **
Phase1 id: **
#show crypto isakmp policy
Global IKE policy
[code]...
We have an HQ site with a 2811 (w/ADVSECURITYK9-M) acting as the firewall. We currently have 1 ASA5505 that has an established ipsec l2l VPN. I'm trying to connect a 2nd ASA, but I've noticed I can only add 1 cryptomap to the outside interface. A show ver shows 1 Virtual Private Network Module... Surely that doesn't mean only 1 VPN?Do I use one crypto map, and add a second 'set peer' & 'match address' inside the crypto map itself?
View 10 Replies View Related