Cisco WAN :: IOS 2650XM To Buy 12.5 With Crypto
Sep 4, 2012I have a 2650XM 16mb flash, 64 mb ram. 12.2(12a). now I want to buy 12.4(25d) with crypto. How much is it? And where can I buy it ?
View 10 Replies
ADVERTISEMENT
Cisco WAN :: 2650xm / 2811 - Hierarchical QOS Over Two Logical Connection?
Nov 16, 2011We have two logical connection which are connected via 1 physical Ethernet interface to 2 routers in central sites. Both connections are 2 Mb/s. How can i classify the output traffic in order to shape both direction to 2-2 Mb/s.
There are not suitable "match" command!!! ??The branch routers are 2650xm and 2811.
Cisco Switching/Routing :: Does 2650xm Or 2620 Can Have 1 Additional FE Card
Nov 10, 2011Need to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies View RelatedCisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?
Nov 25, 2011I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
Cisco VPN :: 877 - Crypto Map With NAT
Mar 7, 2011I have this situation, I need to establish an IP sec communication to another site but I need to identify all my packets sent, as a different networks as my local one. for example: my local network is 10.5.0.0/24 and I need to sent packets as 10.6.0.0/24. I suppose that I need to do Nat with this IPs. But in this router Nat is already applied to outbound traffic to Internet. How can I apply this NAT to crypto map only?
My router is a Cisco 877 with 12.4 IOS an this is the relevant configuration, crypto map vpn it´s used to sent traffic to second site.
crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxxxx address XX.XX.XX.XX
crypto ipsec transform-set vpn esp-3des esp-sha-hmac
crypto map vpn 1 ipsec-isakmp set peer XX.XX.XX.XX
[ code]....
Cisco VPN :: Can SR520 Do More Than One Crypto Map
Jan 11, 2013I'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?
View 1 Replies View RelatedCisco VPN :: 881 ISR Crypto Isakmp Not Available
Jun 26, 2011I have to connect one of our it labors with some ec2 instances in amazon vpc. I downloaded a configuration file from amazon which starts with the command
crypto isakmp policy 200
My router tells me that he does not know crypto isakmp.
I searched on the internet and found that i have to install a specific license, but unfortunately i cannot find which license i have to install.
The show license command show following licenses
AdvIpServices active
AdvSecurity active
advsecurity_npe, ios-ips-update, waas_Express no state displayed
ssl_vpn active but eula not accepted
I found that i can accept the eula license with license boot module c880-data technology-package SSL_VPN command
But this command is also not available on my device. getting the crypto isakmp command working?
Cisco :: C2951 ISR Can't Configure Crypto Map?
Aug 8, 2012i have 2951 ISR but i cant configure encryption it have UniversalK9 IOS and i cant find any other ios that will support crypto map?
View 4 Replies View RelatedCisco WAN :: C1941 Crypto Is Not Enabled
Aug 5, 2012i have Cisco 1941 router with following IOS image:Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2) below mentioned commands are not working :
crypto isakmp policy 5
encr aes 256
authentication pre-share
group 2
what could the issue ? do i need to change the IOS image.
Cisco Firewall :: PIX 525 Crypto Map Correction
Jun 13, 2012This setting is correct?
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 auto
[Code]...
Cisco VPN :: 881 - Isakmp Crypto Module Not Available
Aug 21, 2012I have a Cisco 881 ISR (CISCO881-SEC-K9) and have the advanced security license installed and enabled/active and in use (see screenshot). However, the isakmp crypto module is not available.
[code]....
Cisco VPN :: 2800 - Crypto Map On Dialer Interface
Jul 4, 2011I have applied a crypto map (fo ipsec vpn) on the dialer interface (for PPoE connection) in Cisco 2800; every time when the router restarts the crypto map is removed from the dialer interface even though i save the configuration every tim when i apply the map on the interface. Is there any way that the crypto map remains there on the dialer interface after the restart of router.
View 1 Replies View RelatedCisco VPN :: 121 Output Of Show Crypto IPSec SA
Aug 18, 2011In a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies View RelatedCisco VPN :: 1841 - No Crypto Engine Accelerator N
Feb 16, 2011In my test lab , I have a CISCO 1841 with a AIM-VPN/BPII-PLUS board , everything was working fine , until I would like to see the difference with and without the accelerator.Sins the moment that the IOS told me that he will change to SW accelerator instead of HW accelerator , I can not make it work anymore.I have a copy of the full working configuration before I did this , I have put it back on my router but still NO VPN. [code]
View 2 Replies View RelatedCisco WAN :: How Many Crypto Maps Would 3925 Support
Feb 18, 2011I have a network architecture like the one HERE but with alot more spokes (32). Would my cisco 3925 be able to support so many crypto maps?
View 2 Replies View RelatedCisco VPN :: Error While Configuring Crypto PKI In 2911
Feb 27, 2012I am trying to configure Crypto PKI in ciscio 2911, Once i configured the root certificate for the router , i can see the validity date wrongly but the same certificate is fine in the other devices . [code]e when i am trying to configure the local certificate.
View 1 Replies View RelatedCisco VPN :: 65335 DMVPN Crypto Map Priority
Feb 27, 2013New to the forum and not much Cisco IOS experience let alone on the security side of things. I know how to navigate the IOS and can do basic switching and routing just fine. My company currently has a DMVPN setup w/ about 10 tunnels going back to the hub. We have 4 more sites they want me to setup and I keep getting stuck at the crypto maps. I have been reading about VPN's, DMVPN's , etc. for days now but can't find any examples of how we are configured. The priority of our crypto maps start at 65536 and go up. Default max is 65335 from what I have read, and I cannot assign a priority that high statically. [code]
View 3 Replies View RelatedCisco Firewall :: ASA 5510 Needs Crypto Keep Regenerated
Sep 11, 2012I have a ASA 5510 that has something weird going on I have just added a base config where you can access on a inside interface but for some strange reason after I disconnect i have to ping inside interface first before I can connect via telnet or SSH and then regenerate therecrypto key
View 3 Replies View RelatedCisco VPN :: 1800 - Static Crypto Configuration
Sep 3, 2012I ahve a requirement to configure static crypto for 1800 site and I need to configure on two sepaarte interfacs at spoke site which means I need to configure 1800*2 = 3600 peers at central site. The challenge I have is due to load balancing , the traffic dynamic crypto can not be used since traffic may be initiated from Dc on other link which may get dropped incase not encrypted.
View 5 Replies View RelatedCisco WAN :: 2901 Router Crypto Commands
Jan 13, 2013I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
Cisco :: DHCP Not Allocating Address When Crypto Map Applied
Dec 12, 2012I have a cisco 887 connected as temp measure to a 3g device via a fast0 port. all works fine. VPN comes up...but the moment i apply the crypto map to the vlan.. DHCP stops allocating ip address. I have remove irrelevant config ( dialer, atm etc as they not been used)
config below
p dhcp excluded-address 10.29.80.253 10.29.80.254
ip dhcp excluded-address 10.29.80.1 10.29.80.229
!
[Code]......
Cisco :: Deleting Whole Crypto ISAKMP Setup / Policy?
Sep 27, 2012Just looking at a new clients setup and they have a ISAKMP vpn to the old security company I am trying to remove...I am fairly new to cisco, I actually know how to setup the ISAKMP policies, acl's etc but never had to completely remove one before All I can find is Clear Commands which seem to just flush the config not actually delete any of the policy etc...Its not that urgent as all passwords are changed on the domain and the cisco, the usernames have been deleted as well.
#show crypto isakmp peers
Peer: ** Port: 500 Local: **
Phase1 id: **
#show crypto isakmp policy
Global IKE policy
[code]...
Cisco VPN :: ASA5505 Use One Crypto Map / Add Second Set Peer And Match Address
Aug 24, 2012We have an HQ site with a 2811 (w/ADVSECURITYK9-M) acting as the firewall. We currently have 1 ASA5505 that has an established ipsec l2l VPN. I'm trying to connect a 2nd ASA, but I've noticed I can only add 1 cryptomap to the outside interface. A show ver shows 1 Virtual Private Network Module... Surely that doesn't mean only 1 VPN?Do I use one crypto map, and add a second 'set peer' & 'match address' inside the crypto map itself?
View 10 Replies View RelatedCisco VPN :: 2811 Showing Crypto Map As Empty And No SA Shown
Nov 16, 2011I replaced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config.
View 1 Replies View RelatedCisco VPN :: Crypto ACL Asa 5520 Direct All Traffic To Go Over Vpn Tunnel
Feb 14, 2013we have a L2L-VPN-Tunnel beetween our Headquarter (ASA5520 with Network 10.100.1.0) and a branch office (Cisco1841 with network 10.100.10.0 ). This works fine for years, but now we wish to change the configuration so that ALL traffic from the branch office goes over the vpn-tunnel. My question: How I have to change the crypto acl to reach this. Below the relevant parts of the branch route.
View 6 Replies View RelatedCisco VPN :: 1800 GETVPN Crypto Map On Loop Back
Jan 12, 2013We have 6 WAN routers connected through ISP MPLS cloud , we need to implement GET VPN between these WAN routers.We have 2 Key servers (1800 routers) , and the WAN routers will act as Group Members (6 GMs)
The attached configuration files are for working configuration for typical GETVPN (crypto map applied on WAN interface)
In Key server configuration , the crypto isakmp command is using the WAN interface IP address of each WAN router (172.16.x.x) , and since that the KS routers are connected to local backbone (VSS) , they should be able to reach 172.16.X.X , and therefore the subnet 172.16.X.X is advertised to the local network (check GM configuration file under eigrp - redist connected )
This is what our customer want to avoid ! they do not want 172.16.X.X to be advertised to the local network .I know It is possible in GETVPN configuration to configure ,the crypto isakmp command to use loopback address's of the WAN routers instead of the WAN IP , but in this case the crypto map must be applied to the loopback address , and this requires all traffic to be encrypted and decrypted to go through the loopback interfaces on all WAN routers .
i was wondering what is the best solution for this case , I though to use the below config on the GM's
Cisco VPN :: 1494 / Active Crypto Means No Citrix
May 16, 2011We run a hub&spoke network with dual GRE tunnels from each spoke site to seperate independant adsl routers at the hub.IPsec is enabled on each tunnel with crypto maps and then QOS is enabled with pre-classify for voice traffic priority. We also have defined a class for Citrix traffic by identifying port1494 traffic out and anything bound for our citrix servers IPs.Ok so the problem is that once the encryption comes up on the tunnels, the citrix programs wont connect. Take the crypto map off the tunnel and all works fine.
Here is the relevant config
crypto isakmp policy 1 encr 3des authentication pre-share group 2crypto isakmp key **** address *.*.*.*
crypto isakmp key **** address *.*.*.*
crypto map SDM_CMAP_1 1 ipsec-isakmp description Tunnel to hub1
set peer *.*.*.*
set transform-set ESP-3DES-SHA match address 104 qos pre-classifycrypto map SDM_CMAP_1 2 ipsec-isakmp description Tunnel to hub2
set peer *.*.*.*
set transform-set ESP-3DES-SHA match address 105 qos pre-classify
[code]....
I deliberately weight EIGRP to favour Tun0 and have Tun1 as a failover. I was thinking of Route-mapping the Citrix traffic to Tun1?
Cisco VPN :: ASA5540 Debug Crypto ISPEC 255 Displays Nothing
Feb 19, 2012I have ASA5540 with asa712-k8.bin.
There is a plenty of tunnels ended and it works.But i have one tunnel, which doesn't work.I tried turn on "debug crypto isakmp" and it show this: RECV PACKET from 10.200.79.161 ISAKMP Header. [code]
So there is problem with IPSEC and with no matching SA, but i don't know which one.Then i try to turn on "debug crypto ipsec 255" but it displays nothing. [code]
Cisco WAN :: L2L VPN / 3640 With IOS 12.3(16) - Unable To Recognize Crypto Commands
May 23, 2013 I have a Cisco 3640 router with IOS v.12.3(16) It does not recognize the crypto commands.
#sh version Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3640-I-M), Version 12.3(16), RELEASE SOFTWARE (fc4) Technical Support: [URL] Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Tue 23-Aug-05 20:03 by ssearch Image text-base: 0x60008B00, data-base: 0x60D36000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) ROM: 3600 Software (C3640-I-M), Version 12.3(16), RELEASE SOFTWARE (fc4)
router01 uptime is 3 hours, 43 minutes System returned to ROM by power-on System image file is "flash:c3640-i-mz.123-16.bin"
[code]....
Cisco VPN :: C2811 - (Show Crypto Isakmp / Ipsec Sa) Shows Nothing
Feb 25, 2012I have setup ipsec VPN in my C2811 router but when "show crypto isakmp/ipsec sa" shows nothing. Remote end point is an "ASA5520". Does it indicates that the remote ASA5520 not yet configured?
Code...
Cisco WAN :: IPSec VPN Crypto Sa Is Active But It Doesn't Work 2811
Jul 15, 2012My router is Cisco 2811 with IOS version 12.4(22)T1. It had established IPSec with another peer (203.*.*.250 shown below) for long until recently we make it re-establish IPSec VPN with another peer (203.*.*.30 shown below). It showed that the new sa is active but the result still showed there were 4 deleted SAs. The 4 obsolete sa entries won't vanish no matter what I do i.e. reset the interface, re-create crypto map, clear all sa and etc.
From numerous testings we knew that the VPN doesn't work even the desired sa is there remaining active. I reckon it has something to do with those deleted sas ( i mean it is supposed to show only the last one if it is working fine ). I don't know how it would be come like this as we did pretty much the samething on other VPN routers with no problems.
Cisco VPN :: C2921 / Setting ASA-Router VPN No Crypto Command Options
Jun 4, 2013I am trying to set up vpn tunnel between ASA and router C2921 for site-to-site routing. This was described on many sites. However I do not have required option under crypto command.
g1c1router1(config)#crypto ? key Long term key operations pki Public Key components
g1c1router1(config)#crypto
There are no crypto map etc options.
Some people suggested that I need crypto IOS. I have:
boot system flash:c2900-universalk9-mz.SPA.152-4.M3.bin
license udi pid CISCO2921/K9 sn FGL171910C1
Do I have to generate some keys? How do I do it? crypto key generate ?
Cisco VPN :: 2651 No Matching Crypto Map Entry For Remote Proxy
Jul 14, 2011ASA is the server, 2651 is the client. Phase 1 is negotiating, after entering XAUTH on the 2651, the ASA is showing:
Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 10.250.2.0/255.255.255.0/0/0 local proxy 10.10.3.0/255.255.255.0/0/0 on interface Outside
Not sure what this means in this instance, the maps are setup the same as the article below. I guess I more expected that sort of error if this was a static tunnel and there was an ACL issue. I don't have a lot of knowledge on the Easy VPN with the ASA. [code]
