I have a cisco 887 connected as temp measure to a 3g device via a fast0 port. all works fine. VPN comes up...but the moment i apply the crypto map to the vlan.. DHCP stops allocating ip address. I have remove irrelevant config ( dialer, atm etc as they not been used)
config below
p dhcp excluded-address 10.29.80.253 10.29.80.254
ip dhcp excluded-address 10.29.80.1 10.29.80.229
!
[Code]......
I have two sites.Main site (local) has two Vlans: Vlan1 and Vlan2. Each has its own IP address range.VLAN 1 is the default Vlan and is used for CORPorate traffic. IP range 10.33.4.*VLAN 2 is for guest access to the internet IP range 10.10.10.*I have a WLC4402 on the this site with 2 WLANs: CORP on Vlan1 and GUEST on Vlan2.
Branch site (remote) which has 2 Vlans: Vlan1 and Vlan2. Each has its own IP address range.VLAN 1 is the default Vlan and is used for CORPorate traffic. IP range 10.125.15.*VLAN 2 is for guest access to the internet IP range 10.10.11.*I have an 1141 on this site using HREAP.
Locally, if you connect to CORP, you get a CORP ip address and access to CORP network. If you connect to GUEST, you get a guest ip address and guest access to the guest network. Simple so far....
Remotely, if you connect to CORP, you get a CORP ip address 10.125.15.x and access to CORP network (great). If you connect to GUEST, you get a CORP ip address 10.125.15.x and access to CORP network (not great). This is with the HREAP native vlan ID for the access point set to 2 on the controller.If I set the native vlan ID to 1 on the controller, I can not get an IP address at all.If I do not set the native vlan ID on the controller, I can not get an IP address at all.
I am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.
View 24 Replies View RelatedI have noticed that changes in MAC address filter list are applied only after reboot of router. It is inconvenient.
Router Linksys E4200
Firmware Version: 1.0.03
Operation system on client computer is Windows 7.Can it be resolved in the next version of firmware?
We have an HQ site with a 2811 (w/ADVSECURITYK9-M) acting as the firewall. We currently have 1 ASA5505 that has an established ipsec l2l VPN. I'm trying to connect a 2nd ASA, but I've noticed I can only add 1 cryptomap to the outside interface. A show ver shows 1 Virtual Private Network Module... Surely that doesn't mean only 1 VPN?Do I use one crypto map, and add a second 'set peer' & 'match address' inside the crypto map itself?
View 10 Replies View RelatedI'm planning to setup a network with more than 300 PCs. I know that using class C address is not enough to allocate number of IP addresses required. What I meant in the preceding sentence is that If I use this network address 192.168.1.0 (class C), it will allow only 256-2 = 254 IP addresses, What about other PCs in the network ?
View 3 Replies View RelatedI have an apartment with a shared internet connection with a roommate. I'm paying for all internet costs because he says he "doesn't use it as much as I do". He frequently slows my connection down by downloading movies and probably porn. Time to bottleneck this douche.
I have an ASUS WL-520GU All four slots are hardwired: my computer, his computer, PS3 in the main room, printer.Plus several mobile devices are connected via wireless throughout the day.I only want to bottleneck his computer.How do I do it?
We are currently running a ACE20 with 11 contexts. Recently we have seen that one of the contexts is being 'starved' of resources, especially Concurrent Connections, Bandwidth and Throughput.
Whilst we know how to address this situation by reallocating resources from less busy contexts, I was wondering if there was a more scientific way of looking at the resources being used and calculating the best way to allocate them across the ACE other than just looking at the 'show resource usage' and 'show resource allocated' commands?
Has Cisco or any other 3rd party developed a handy tool to monitor the the ACE resources which will possibly assist with calculating the optimum resource allocations across all contexts?
My customer requires the hostport on an access switch to be allocated to a specific Vlan based upon the AD Group that the user is a memeber of ? I am planning to setup NAC in a Real Gateway OOB deployment, using an ACS 5.2. I was initially thinking that the initial authentication server would be the ACS and then the AD, which using group mappings within the AD, I could then assign the user to a specific ACS group and then pass a Radius attribute back to the NAC manager for processing?
View 2 Replies View RelatedI have a cisco 850 that is not getting a WAN ip address thorugh DHCP. I have FE4 (The WAN port) set to get an ip address via DHCP, but when I do a test connection from CCP I get this error: Checking interface IP address…failed.No Ip Address for the interface has been obtained. The interface is configured to obtain an ip address through dhcp. The remote end may not be configured with a dhcp server or the dhcp pool may be empty.
Please contact your ISP or WAN administrator and check if the server has been configured to lease ip addresses to the client’s connection through DHCP. Retest connection.I know that the modem is providing an ip address via dchp, because I can plug my computer directly into the modem and get an ip address, so I think I may have missed a setting on the router. Here is he running config: [code] I think the problem may be the Firewall is not letting dhcp through (even tough I haven't set it up yet, and there are no rules in the firewall yet). But I'm not 100% sure about that.
I have an intermittent issue getting a DHCP address when using a Cisco Wap 200. Sometimes i can get an address but most of the time my devices fail. This happens with / without WPA or WEP.
View 7 Replies View RelatedI am running a Dell Inspiron 530 with Windows XP SP 3. My computer is displaying cannot aquire network address, can't contact dhcp. I have already had the modem and ethernet cables tested, they're fine, and I have tried replacing the network card, no luck. I have also run ip config renew and replace as well as ipconfig/all everything was zero. I checked the startup menu and all the appropriate network apps are marked started and automatic.
View 11 Replies View RelatedI disconnected and reconnected the powercable while holding on to the setup button until system, alert, setup go amber. The system led light began blinking green. I waited until one of the leds lights on the ports starts blinking green I then connected the ethernet cable connected to my pc. I made sure my lan connection on my computer was set to dhcp.In the docs claim it should take about 1 minute to grab a new ip address. After a few minutes i check the ipconfig on my pc and I get the apipa address.The setup light on the switch remains green while system is amber. The led for port 1 stopped blinking and remains green.My pc is not grabbing an ip address I don't know what else to do.
View 7 Replies View RelatedI just tried replacing a cheap domestic router/switch with an RVS4000 V2 on our work network. This has a WAN connection to a cable modem for internet access via a dynamic IP address.
When I first connected the RVS4000 it got a WAN ip address via DHCP of 192.168.100.11. This is the type of IP address we get when there is an upstream problem with our ISPs cable network, and sure enough we had no internet access. The RVS4000 was set to use DHCP on the WAN interface. So I logged a support call with our ISP but they said there were no problems at their end.
I then swapped the RVS4000 out for the original router. This worked fine and got a WAN DHCP address of 77.xxx.yyy.zzz as it should. Swapped back to the RVS4000 and back to the same problem of getting a 192.168... address.
So, I downloaded the latest firmware from Cisco, which was V2.0.3.2 and flashed the RVS4000.
I then tried again connecting the RVS4000 to the cable modem but this time it would not get any WAN DHCP address at all. On the Status/Gateway page of the web interface it said that the WAN interface was down. However, on the front panel there was a yellow light indicating a live connection on the internet port.
I use the dhcp demon (dhcp server) on my PIX 501 to give my local clients automatic ip addresses, my dhcpd config is here:
dhcpd address 192.168.251.20-192.168.251.40 inside
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd domain lokalnet
dhcpd enable inside
I know DHCP can assign more than just address, mask, and gateway. It can also assign a hostname, and DNS. Does anybody know if it can also be used to assign an SNMP address?
View 6 Replies View RelatedI have 2 computers that cannot/will not acquire an IP address from my DLink router.There are 2 other computers that aren't having any problem at all...so I assume that it is not a problem with the DHCP service of the router. The 2 computers are laptops: one netbook running Windows XP and another standard laptop running Windows Vista Home Premium x86. Both computers are running McAfee and I have scanned with McAfee and Malwarebytes, and both are malware-free (no infections were found on either system on first scans...so it's not like I'm dealing with a system that has had infections removed). When connected to the network, they attempt to acquire an IP address, but cannot for some reason and then Automatic Private IP Addressing takes over and they come up with a 169.254.x.x address. I cannot figure out why this takes place, as I have gone through Winsock repair, uninstalled and reinstalled both network adapters (ethernet and WLAN) on both laptops and nothing seems to make a difference. I have even tried disabling APIPA by adding the "IPAutoconfigurationEnabled" DWORD value in the registry......still the same. I have manually configured the adapters with a static 192.168.0.x address, and I can begin to communicate on the local area level...but still cannot establish any kind of Internet connection.
View 19 Replies View RelatedThe laptop can connect to the internet using the wifi card. However, it cannot connect to the internet when using the wired connection but it can be pinged from other machines at work. The NIC does not pick up a different IP address even after releasing and renewing the IP address through cmd. I have uninstalled and reinstalled the NIC. The NIC is working because when I set a static IP address the machine can connect to the net. Using DHCP it goes back to that same IP address. I have tried a winsock repair as well with no go, as well as taking the machine off the domain and re-joining it. Is there something I can do on my end to get a different IP address through DHCP or do I have to get a Network engineer involved? This is a machine on a corporate LAN?
View 15 Replies View Relatedi did just had a rogue anti-virus infection i did a removal of it AV Security 2012
View 1 Replies View RelatedI am using Windows 2011 SBS and Windows 7 clients.My server has a DHCP range of 192.x.x.150 to 192.x.x.199 and all other I.P. addresses are static. On a workstation located at I.P. 192.x.x.13 I am seeing an address conflict.When I perform an "nbtstat -a 192.x.x.13" command from the server I am given the logical computer name of a staff members personal laptop.Investigation of the laptop reveals that it is set to DHCP, and clearly the address of 192.x.x.13 is outside of my servers DHCP scope, so this I.P.should never be assigned, let alone in duplicate.I Google this topic before posting, and it was suggested that IPv6 could be having an adverse affect. I determined this because I performed a ping on the laptop and only got a MAC address back rather than an I.P. address.However after unticking IPv6, and rebooting, the laptop is still causing havoc.I can set a static I.P. address on the laptop, however this is not ideal.
View 2 Replies View RelatedI wanted to connect to the Internet but my laptop has this message: " Your IP address lease has expired. DHCP was unable to renew your lease." I cannot connect to the Internet. What should I do?
View 1 Replies View Relatedproblem is my brother has been playing with its config page. he changed the IP Address of the modem and disabled DHCP. he forgot what IP Address he inputted on the config page. I tried resetting the router with the small button on its side. Nothing happens. all the lights blink when i pushed the reset button for 10 sec. but nothing happens. i still can't access its default IP which is 192.168.1.1 IS there anyway to determine its IP Address even if DHCP is disabled ?
View 5 Replies View Relatedi have configured wlc 2504 .in that i have configured two interfaces.one is guest, 2nd is internal user, the pblm when user try to connect with that contain ssid user not getting ip address,
i have connected only one link between core to wlc on port 1.for guest interface i used port 4.but no physical link.
I would like to share one problem with WLC 5508 . we added a new virtual interface on the WLC. One new SSID is associated with this interface.
We created a ACL for this interface to restrict the access via WIFI to certian services. It´s not correct that everything works fine because the change were not applied. [code]
The changes of the ACL are applied on the fly, but for reason we don´t know, the clients don´t get a DHCP IP-Address (after changing the ACL) until the Controller is rebooted.
Currently we're providing DHCP to wireless clients from a dhcp pool on a cisco 6500. Due to new requirements we need to move to windows 2008 dhcp and when I test this on an unused WLC (7.0.235.0) the client doesn't get an address.
When I do a packet capture on the client I see it requesting dhcp but not getting any response from the server. When I do a dhcp debug on the client I see the same (see attached file).
This seems to me to be a server issue but the same server is supplying addresses to wired clients.
Is it problem with iPads or LAP1141n?WLC 4404 and many 1142 and 1141, so other devices laptops, iphones, androind phone works as well.But iPad authorized, but can't get an ip address from dhcp server (dhcp not local on wlc, on windows machine) with coverage lap1141, but it get ip with coverage lap1142, and when i got it i roaming to lap1141 and it stays, if i off/on iPads can't get it again from lap1141.
View 14 Replies View RelatedI have a issue where after configuring aaa and rebooting, logging into the console port seems to be auto trying something before it finally times out and let's the user try. I getting the following sequence: [code] I need aaa to work via vty, however I need the device to boot directly to the Username: prompt so I can continue to use my VB script to clear the config when the devices are return from the field.
View 4 Replies View Relatedmy Laptop is about nine years old, HP Pavillion Pentium 4. I run Windows XP Home Edition Version 2002 SP3. I use a broadband card from Verizon that I just put in my USB (no router, etc) I'm getting a System Error Source DHCP Event ID 1002. When this happens, my computer, I believe, is going into sleep mode and I have to reboot the system. When I turn it back on and go back on the internet, all my websites that I was in are still there. The error says: The IP address lease 10.170.223.48 for the Network Card with Network address 2c3068c16ED1 has been denied by the DHCP Server 10.173.229.86 (The DHCP Server sent a DHCPNACK message)The DHCP Server Service did not extend the lease on your computer's IP address, so your computer temporarily lost its connection with the Network. I tried the ipconfig /release and ipconfig /renew. I tried going in services.msc and going under DHCP and keeping it automatic but stopping it. I called Verizon and I believe he refreshed my Network settings (I think I knew more about the topic than he did) He said it was my computer, whatever. I just tried the static IP but it didn't seem to take. I restarted and it jumped back to automatic. My last guess is it's something to do with the time frame of when it automatically obtains the address and when it expires. When I do the ipconfig /all it shows only a two hour time frame before it expires. Today I noticed that my computer shut down/sleepmode at the exact time the ipaddress was obtained. So, is there a way to increase this time between obtaining and expiring?
View 7 Replies View RelatedI'm a heavy PC Gamer, I play games such as World of Warcraft, Borderlands, Call of Duty, Steam Games, I also know my way around fixing internet issues, But this one just seems to have gotten me off guard, Recently, 1-2 days ago, I was browsing the internet like a normal day, and It was late, so I decided to go to sleep, Turned my computer off, Woke up the next morning, Turned it on, It then shows that I kept getting kicked off the LAN for some reason, It was like this[CODE]
View 2 Replies View Related I've came across IP address that aren't enough for some users in the company. The IP addresses are more than enough to cater to the user's notebook or PC. However, some users does not know that there are actually limits to the IP we have, so quite a number of them actually uses their mobile / pads to tap the company's wireless.
I was wondering if i could restrict that particular user from tapping onto the network. I know it sounds a bit impossible because DHCP doesnt have that smart function to block whoever we sees deemed as a "nuisance".
I just got a brand new laptop and I can't get it to connect to LAN.It's plugged in to the same hub as my main machine and I can't even access my router UI.It's not the cable because I tried plugging in my main machine's cable to the new laptop and the same thing happens.ipconfig reveals an Autoconfiguration IPv4 Address of: 169.254.197.187 But that number should say 192.168.1.1xx I've tried uninstalling and reinstalling the Ethernet driver as well.I've tried resetting the router and modem.I've tried resetting TCP/IP.
View 13 Replies View RelatedI have an Avaya IP Phone for work. This has been tested at work and works as expected. After the IP Phone boots it's able to obtain an IP address from work. At home when I plug the IP phone into my DIR-655 router, it's unable to obtain an IP address. Other network devices are able to obtain an IP address, for example any computer or laptop. Also my wireless works with no issues expect for the IP phone. I've already done some searching and found other users with the same issue but I haven't been able to find a solution other than setting a static IP address. I'm curious why this relatively new router won't work with an IP phone. I've played with some of the router settings but it didn't make a difference. Any work around to get the DHCP to work? I'm running the latest firmware for my router: 1.35A Hardware Versions: A4.
View 9 Replies View RelatedMy WRVS4400N, V2.0.2.1CPU:STAR 9202.Doesn't allocate IP address on DHCP for anything but the Open SSID. All others, WEP, WPA, WPA2, nothing.I tried different clients, Intel Centrino wifi, Cisco, AG-CB21 same results.The config is std, I tried one VLAN for ALL SSID, I tried different VLANS, same.
View 0 Replies View Related
