I have noticed that changes in MAC address filter list are applied only after reboot of router. It is inconvenient.
Router Linksys E4200
Firmware Version: 1.0.03
Operation system on client computer is Windows 7.Can it be resolved in the next version of firmware?
I have a few desktops in my home network with a new E4200 router. Have to add my wifes Lenovo notebook to the net and activated MAC filtering as addition to the WPA2.Set her MAC address in the filter list. Only one MAC is allowed to access WLAN.An hour later I see in the Filter list four (4) different and unknown MAC adresses added to the list.
View 8 Replies View RelatedI am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.
View 24 Replies View RelatedWe have a wifi router RV220W and we need to filter the mac address. The problem is that the number of the "allowed" devices is around 50 (not all connected at the same time), but the maximum number of mac address which can be listed in this router for each VLAN is 20, so for the moment we set 3 VLAN, each one with a different mac adderss list. This is very awkward because the area to be covered by the wifi network is large and we need repeaters, but having 3 VLAN we should put 3 repeaters for each point. Is there any way to configure this router in order to have a single VLAN but with a mac address filter list of 3 x 20 mac address?
View 1 Replies View RelatedIt would be nice if there was a "Note" field next to each MAC field whereby you could specify what device the MAC belongs to. I have quite a few listed but recently I've gotten rid of the devices. I have to go through all my current devices, not them in another program, and then remove the ones that are no longer needed.
The Wireless Client List doesn't capture all the names so that's not what I'm looking for.
Also, it would be great if the "Note" would tie into the Parental Controls so that I know exactly what device I'm choosing. It currently lets you select from the Wireless Client List, but the list doesn't have all the Client Names populated.
So, one, is this feature available (or something similar) and two, if not, please take this into consideration as a useful feature for a new version down the road.
If you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View RelatedI don't know how many of you read the article List of tested USB storage devices for the Linksys E4200 before buying it. Basically, what it says, is that you cannot connect your "too old" or "too new" (>2TB) HDD to this router and you have to settle with an WD MyBook Mirror Edition 2TB or Seagate FreeAgent Desk 2TB at best. Needless to say that this not good enough. First I believed that the list is incomplete and if a brand is listed with a model then a bigger or a smaller one will work as well. Sadly this is not the case: neither WD Passport with 320 GB (FAT32) nor a LACIE 1TB (NTFS) could be connected to E4200.
If any of you succeeded to pair the router with a different external HDD than the ones from the.
P.S.: I strongly believe that Cisco should work on an updated firmware which should expand the list of supported HDDs.
I want to add more than 40 mac address filter into my WRT54GL with firm version V4.30.7 but the form to enter the mac address list just limited to 40 mac address register. How do I can add more than 40 mac address list in my WRT54GL ? perhaps we can add the list into WRT54GL like XML file or somehow that can make me add more than 40 mac address register list.
View 2 Replies View RelatedI'm looking for an updated list of tested and compatible external HDDs that the 4200V2 will support f(media streaming). Any updated list?Clarify that the following references to "WD 1.5 & 2 TD" translate to WD My Book Essential Edition 1.5 & 2 TB as opposed to the WD Elements HDDs? There has to be a better list than the one in FAQs.
View 1 Replies View RelatedThe official List of tested USB storage devices for the Linksys E4200 is so short, and the fine print "If your USB storage device is not listed on the table, it is not guaranteed to work with the router" is very discouraging. Let's create the community-based list of tested External Hard Drives for the Linksys E4200? Post here the brand / model of your external hard drive which works well with your E4200. State Firmware version as well. My Toshiba 640GB Canvio® USB 2.0 Portable Hard Drive (Toshiba P/N e05a064cau2xr, M/N 593400-b), when connected to E4200 Firmware v1.0.03 (Build 14), stops the router's both wired and wireless connection after a couple of hours.
View 9 Replies View RelatedOne of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies View RelatedI could get a list of clients on the E3200 wireless (or wired) ports. I have my E3200 setup as a WAP LAN-LAN off a switch and it is not the DHCP server on the network. I can see a list of MACs on the client list, but no client names and no IP addresses. They are definitely named and show up on the WRT54GL (DHCP and NAT) as devices
View 5 Replies View RelatedI have a router 2811 that it's configured with VPN remote access and I'm trying to block clients based on their MAC address, I tried configuring access interface as routing/bridging, configured an ACL 750 for 48-bit MAC address access list and enable "bridge-group 1 input-address-list 750" command on bridged interface, but the only match I got when VPN clients access the LAN is from router interface.
Internet(VPN) ---> Router1 (FE 0/1) ---> Router1 (FE 0/0) --> Router2 (FE 0/0) --> Router2 (FE 0/1) --> LAN
I tried configuring on Router1 (FE 0/0) interface and also on Router2 (FE 0/0) interface with same behaviour. Router2 is used for internal NAT.
bridge irb
bridge 1 protocol ieee
bridge 1 route ip
[Code].....
I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.
I just bought the Cisco e4200 v2 router, I did all the installations as the Cisco connect software instructed me and everything went fine.After the installation I configured the router on the WAN settings as (Automatic Configuration - DHCP), like my old router (Linksys WRT54GL) and I saw that my router doesn't get the WAN address from cable modem from my ISP(it stays on 0.0.0.0), it doesn't renew the IP address.
View 3 Replies View RelatedMy wife accidently reset the password on our E4200 wireless router and did not write it down. I have tried to reset the router as well as run the set up CD - no luck. How can I recover and get my wireless network back in operation?
View 1 Replies View Relatedi got an E4200 V2 and it is updated to Linksys Smart Wifi firmware.. Is it possible to block a specific public IP address?
View 4 Replies View RelatedAfter an indeterminate period my E4200 (firmware version 1.0.03) stops renewing the Internet IP address. This happens in both router mode and bridge mode.In router mode the E4200 is set for DHCP and connected to the cable modem, in bridge mode it is connected to a Dell switch with DHCP being provided by my Win2008R2 server.It appears that the device stops recognizing the existence of the Internet port - no lights come on when a cable is plugged in - whether connected to the cable modem or my Dell switch. Plugging the same cable into one of the 4 lan ports and that port lights up immediately (i.e. it is not a patch cable problem).If the E4200 is left switched off for some time (possibly days) it will work properly again for a while.
View 6 Replies View RelatedFrameware version: 1.0.03.
Environment: Internet (external IP say 24.x.x.x) ISP provided modem+router (192. 168. 1.x/ 24 IPTV network) E4200 (192.168.0.x/24 my home network).
The DDNS option page did report update succefully and shown the external IP address correctly on the page, however when I login to dynDNS it shows 192.168.1.x, which is the E4200 IP dhcp from the ISP's router.I know that it's double NAT, but the 192.168.1x/24 subnet is the IPTV subnet, and my old Dlink router did support and update the dynDNS entry properly.
I replaced my old wireless router with a Cisco Linksys E4200, running firmware version 1.0.02 build 13 May 24, 2011. About once a minute the router sends an unsolicited DNS message to the IPV4 multicast address 01:00:5e:00:00:fb with a destination IP address of 224.0.0.251. The unsolicited message is a DNS response with source port 32784, transaction ID 0, flags 0x8400 (standard query response, no error), questions 0, answer RRs 2, authority RRs 0 and additional RRs 1. The two answers both relate to the router itself: one has Name Cisco18738.local, type A (host address), class 1 (IN), cache flush true, time to live 1 minute, data length 4, and the address of the router. The other is the reverse of the same address. The additional record is for Cisco18738.local, type NSEC, class IN, cache flush true, time to live 1 minute, data length 5, next domain name Cisco18738.local, RR type A (host address).
When my desktop computer receives these messages it logs an error, for example: "Jun 23 07:39:22 sauterws02 avahi-daemon[1067]: Received response from host 10.146.9.1 with invalid source port 32784 on interface 'eth0.0'" The 10.146.9.1 is the router's IP address. I also see these messages on the wireless link from my laptop.I suppose the E4200 is generating these DNS messages in a misguided attempt to make sure there is no old information about its name. Is there a way to turn them off? If not, is there a way to report this to Cisco as a bug?
I've got threeLinux Boxes (running Centos 6). They were all connected to my cheap WRT54GL-- DHCP worked every time.Absolutely no problems. Both the LInux boxes and the WRT54GL had MTU set to manual, 1492.I replaced the WRTt54GL with the expensive E4200. I set the new router's MTU to manual, 1492. NONE of my Linux boxes ever receive a DHCP address. I look at the logs, and they do DHCPDISCOVER, get DHCPNACK, try several different intervals, and then fail the interface and quit.ALL I did was unhook cables from the WRT54GL and plug into the E4200. Yes, the WRT54GL was powered off. NOTHING was changed in the Linux configs. Yes, DHCP is enabled, address-range assigned, etc. BTW-- one box is dual boot with Win7-- in Win7 (using the same card, obviously), DHCP works just fine. But, Linux doesn't work.
I can give the boxes static IP's, and all is well. Just can't get DHCP to work. I evfen tried putting in DHCP reservations (via MAC assignments) for the E4200-- still doesn't work. The new E4200 is on the 02 firmware (which I believe is cuurent). If I can't iron this simple task out, in a couple of days I'm taking the E4200 back, and getting a refund. I'll stay with my old WRT54GL... it works. Hate to give up on some of the new E4200 features, though.
I've tried to cascade two Linksys routers, but It hasn't worked for me. The first one (which has cable-modem connection) is the brand new E4200, and the second one is the old WRT54GCv3.[code] However, the WRT54GCv3 doesn't get the IP address from the E4200's DHCP. I've also tried to connect them directly (without the PLC), even specifing an static IP on the second router, but I got the same results.I've to state I don't want to change the first router IP/gateway parameters because I have a web and game home server working with an static IP and I don't want to put it offline temporarily because of readjusting network parameters.
View 9 Replies View RelatedI have E4200 with fixed ip 192.168.1.2, DHCP off connected through LAN ports to FIOS ActionTec as 192.168.1.1. When connecting through wireless network off the E4200, I can obtain and connect fine under Guest network and WEP security, but for any other security setting, WPA, WPA2, Mixed mode, etc. I get the message "Aquiring network address" forever, and I never get a connection.
View 1 Replies View RelatedI have a Linksys WRT54G router.I am trying to set up my internet connection so only my approved MAC Addresses can connect.I set everything up. I purposely excluded my laptop from the list to see if I did it right and I guess I didn't because my laptop is still able to connect to my network.
View 7 Replies View Relatedit would be possible to configure a White list on the SRP500 URL filter. In other words the customer wants to specify allowed URL's and all other URL's must be blocked.
View 1 Replies View RelatedI have a cisco 887 connected as temp measure to a 3g device via a fast0 port. all works fine. VPN comes up...but the moment i apply the crypto map to the vlan.. DHCP stops allocating ip address. I have remove irrelevant config ( dialer, atm etc as they not been used)
config below
p dhcp excluded-address 10.29.80.253 10.29.80.254
ip dhcp excluded-address 10.29.80.1 10.29.80.229
!
[Code]......
I tried to configure my wifi router recently to secure my internet connection. I wanted to add a MAC adress filter, but I had to leave before I could enter them all. I thought that I wouldn't have to enter my own MAC adress since I'm directly connected to the router with a wire, but it looks like I should have entered my MAC adress, because now I can't get access to my router by typing the IP adress, as usual. I tried to reset it, but it doesn't work.
View 2 Replies View RelatedIf i fully populate all switch port (Cisco 3750 series) with 100 filter list on each port is it recommendable.
View 4 Replies View RelatedI have changed from a DSL internet service to a Comcast cable system. I have setup my E4200v1 router as an Access Point, to extend coverage in my building. It works fine, but I can no longer log on to the unit using its' IP address 192.168.1.1. The browser returns the message "Internet Explorer cannot display the webpage." If I want to tweak the settings the only thing I can think to do is to push the reset plug, back to factory settings and go through the whole process. Is there a way to discover the new IP address of the reconfigured router? I left the default address as it was when I made the changes to AP status.
View 1 Replies View RelatedIm using my upstairs neighbors wifi with permission. It has no protection whatsoever but recently i havent been able to use it anymore, and they both just went on vacation yesterday. Their dad was there for a day or two before they all left, my assumption is he thought i didnt have permission and did something to prevent me from connecting without mentioning it before they left.Its full bars (its directly above me) but the router almost instantly doesn't respond when i try to connect. Did he mac filter my wireless adapters adress? I tried changing my mac address on my wireless adapter (aka, desktop, as it doesn't have a nic) but Tmac cant change it successfully. Tmac is able to change my laptops mac though, but even after doing so i still cant connect to the network.
Other issue - right now im using a crappy 2 bar connection called ddrtvap on my laptop. The laptop sitting right where my wireless adapter for the desktop would be and it connects fine, but my desktop cant connect to this network (it connects to the network, but no internet) while the laptop does just fine. Windows repair is super usefull as it tells me something is wrong with my adapters settings but gives no clue as to what.
I'm havoing probems with my network "stuttering" and wanted to update the firmware. The RVO82 is currently running v2.0.0.19-tm and I have downloaded the latest; V 4.0.0.0.07-tm and tried to upload it to the router using both Safari and Firefox but the update won't take. I have followed the instructions to go to a fixed ip of 192..168.1.50 and have a connection directly to the router( bypassing the switch) but cannot get it to update.
View 1 Replies View RelatedI have gone through the data sheet of WAP4410N,bu have got nothing about the scalability of MAC address filter on WAP4410N?
View 1 Replies View RelatedThe wireless client can't get the DHCP address when I enable the On-MAC-Filter-failure, MAC Filtering and Web Auth. Client can get the DHCP address when I only enable the Web Auth in the same WLAN SSID. The WiSM verion is v7.0.235.0. [code]
View 1 Replies View Related