I have a issue where after configuring aaa and rebooting, logging into the console port seems to be auto trying something before it finally times out and let's the user try. I getting the following sequence: [code] I need aaa to work via vty, however I need the device to boot directly to the Username: prompt so I can continue to use my VB script to clear the config when the devices are return from the field.
View 4 RepliesI have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G
Total Output Errors 0 47749
Small Buffer Misses
4 misses
139 misses
[code]....
I would like to find out if security plus license ASA-5505-sec-pl be applied to ASA5505-K8. I think the strength of encryption should not be determining whether additional feature can be applied or not, but I need to confirm with you people..
View 1 Replies View Relatedcrypto map mapName 20 match address NAME_20_cryptomapcrypto map mapName 20 set peer IPADDRcrypto map mapName 20 set transform-set ESP-3DES-SHAcrypto map mapName interface IFNAMEcrypto isakmp identity addresscrypto isakmp enable IFNAMEcrypto isakmp policy 10authentication pre-shareencryption 3deshash md5group 2lifetime 86400crypto isakmp policy 30authentication pre-shareencryption 3deshash shagroup 2lifetime 86400crypto isakmp policy 50authentication pre-shareencryption aeshash shagroup 2lifetime 28800(code)
I need to be sure that when traffic matches access-list "NAME_40_cryptomap" Isakmp policy 50 are used. And then traffic matches "NAME_20_cryptomap" isakmp policy 10 are used. How do i link the crypto map with the specefic isakmp policy?
I encountered this problem with cisco 870 atm interface. I applied service-policy output, its being accepted but when you do a show run interface, it's not there.
View 5 Replies View RelatedI get that to avoid fragmenting the packets we need to reduce the MTU to 1492, fine, but should the MTU restriction be applied at the virtual-template (server)/dialer (client) or on the physical ethernet interfaces?If I apply it to one or the other, which takes precedence? Should I just apply it to both the virtual/dialer interfaces and the ethernet interfaces?
View 6 Replies View RelatedI have a cisco 887 connected as temp measure to a 3g device via a fast0 port. all works fine. VPN comes up...but the moment i apply the crypto map to the vlan.. DHCP stops allocating ip address. I have remove irrelevant config ( dialer, atm etc as they not been used)
config below
p dhcp excluded-address 10.29.80.253 10.29.80.254
ip dhcp excluded-address 10.29.80.1 10.29.80.229
!
[Code]......
I have a cisco ISE 3355 and WLC 5508 and microsoft Active Directory 2008. I joind the ISE to the ADe successfully and I can see all groups on the AD, also I integrated the ISE with the WLC. my problem is when I created the Authentication policy on the ISE and joined to the AP by the PC nothing applied to the PC.
WLC version 7.4
ISE version 1.1.1.268
my client insisting to set a dscp value of 56 (= CS7 , the highest priority) for their video packet without any bandwith restriction in the input of fast ethernet port and PPP Multilink serial output port of the 7513 router. What will be the outcome at time of video streaming and video conference ? As this dscp value CS7 is the highest priority and reserved for network only.we are using ospf routing (some of the network is connected through this multilink port via ospf routing), also this ethernet is connected to various statice routed ip network via cisco asa and cisco 4507. The keep alive ospf neighbor router will be lost or not?
View 2 Replies View RelatedI have a connection between HQ and Branch which connected by GRE tunnel over IPSec. I use Cisco router 3745 that has IOS version: 12.3(18) and Cisco router 2911 that has IOS version : 15.0(1r)M9 with ipbase, security and data license.
I tried to apply command to both routers as follows:
Cisco 3745 (HQ)
crypto isakmp key test address 10.1.1.2
crypto isakmp keepalive 60
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto map vpn01 local-address Loopback0
[code]....
When I appied this command that will show a notification as below:
NOTE: crypto map is configured on tunnel interface. Currently only GDOI crypto map is supported on tunnel interface.
*** After appied this command, I cannot ping or send any traffic to HQ. ***
I use this command that is working normally on Cisco router 3745 that has IOS version: 12.3(18) and Cisco router 2811 that has IOS version : 12.4(7b).
it seems that users with active device authorization - e.g. permitting only a certain user defined group - can anyway view all devices or views?Is it possible to apply the same view rule from user management, so that these users can only view certain devices or topologies?
View 5 Replies View RelatedIn earlier versions of LMS it was possible to choose i.e. the Routers category (top level) and enter a series of commands to be excluded from the comparison. In LMS 4.0.1 I experience, in several different installations, that this is not possible. It seems I can enter one exclude command beyond the defaults per category, the rest is not applied even though the feedback from the application is positive. Next time I access the Exclude Commands view, the commands I entered are gone. Is this a change of behaviour or a bug?
View 2 Replies View RelatedSo there are two VLAN's traveling over the port attached to the controller (User vlan 100, and Guest vlan 102). I need to block the guest from everything but the internet allowing the free flow of everything else on the User vlan. All info sanitized of course.I think I have the ACL's correct for what I am trying to accomplish I just can not get this ACL to work on a trunk port.Confirmed the ACL to work correctly on access ports however.
ip access-list extended Wireless
permit ip 172.100.0.0 0.0.255.255 any
permit udp any any eq bootpc
permit udp any any eq bootps
permit udp any any eq domain[code].....
I am having ASA firewall 5520. I want to block yahoo mail, gmail using regex for particular users only.
View 5 Replies View RelatedI need to Upgrade my NCS to version 1.1.0.58. Actually my NCS is in the version 1.0.1.4 and i have a lot of templates configured and 1500 Access Points applied.
I have 5 WLCs and will do too the upgrade in the WLCs to version 7.2.130.0.
Will I lose some configuration with these upgrades ? Because the version 1.1.0.58 has more features than version 1.0.1.4 in the NCS and the WLC was adjusted some bugs.
The configurations that i has in the NCS version 1.0.1.4 is H-REAP and in the version 1.1.0.58 will be the FlexConnect, theoretically is the same, but i don't know if the configuration is the same in the two versions.
Can i do a downgrade in the NCS from version 1.1.0.58 to 1.0.1.4 if i have problems ? I was looking for a document who show how can i do this, but i didn't find nothing about.
How to check applied group policy on the domain clients
View 1 Replies View RelatedI'm havoing probems with my network "stuttering" and wanted to update the firmware. The RVO82 is currently running v2.0.0.19-tm and I have downloaded the latest; V 4.0.0.0.07-tm and tried to upload it to the router using both Safari and Firefox but the update won't take. I have followed the instructions to go to a fixed ip of 192..168.1.50 and have a connection directly to the router( bypassing the switch) but cannot get it to update.
View 1 Replies View Relatedwe're having an issue with the command "cts dot1x" when applied to an uplink interface. It basically kils the connection with this command is applied. Once you remove it, everything is back to normal, the platform is a cisco 3750x.
View 0 Replies View RelatedI have a 3560G and an ASA FW, for which I am trying to use PBR to append the next hop. The gateway is the switch VLAN address and the amended net hop is the same VLAN interface on the ASA. Trouble is, I can ping the FW from a client, but not the switch. If I remove the route map, I can ping both. Even more strange is this is the case for some VLANs, but not all!
Config:
HOST ON VLAN 96
IP 10.11.120.99
S/M 255.255.255.240
[Code].....
I have a customer that has a stack of 3750x switches installed in production and now would like to install the powerstack cables. The switches are in production and downtime would like to be avoided. Can you install the powerstack cables with the switches powered up? I would assume you can, but wanted to verify before doing so.
View 4 Replies View RelatedI am confused on how acl's respond on normal cisco switch (eg.6500) when applied on respective vlans. this is my scenario:on a 6506, i have 2 main vlans in question: Vlan 100 ( vendor1 - 172.16.100.0/24 ) & Vlan 200 ( vendor2 - 172.16.200.0/24 ). the requirement is,
- vendor1 should be able to access/ping vendor2 end points
- vendor2 should not be able to access/ping vendor1 end points
Now, if i ping from a host 172.16.100.11 in vlan 100 to another host 172.16.200.21 in vlan 200, will i be able to get a successful response ?
I am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.
View 24 Replies View RelatedI have noticed that changes in MAC address filter list are applied only after reboot of router. It is inconvenient.
Router Linksys E4200
Firmware Version: 1.0.03
Operation system on client computer is Windows 7.Can it be resolved in the next version of firmware?
This is the first time I am trying my hands on wireless gears. I have 2500 WLC and 1142 AP (which I converted from Standalone to LAP).I have a layer 3 POE switch where i am using port 1 for the WLC which is a trunk port.
Port 2 is for the AP using access vlan 111
Port 3 is trunk port going to a router where i am running dhcp server for the VLANs which are as follow:
VLAN 110 -Corp Wireless (10.1.110.0/24)
VLAN 111 - AP-Mgmt (10.1.111.0/24)
VLAN 999 - Guest (10.1.101.0/24)
I wanted to block the traffic from the Guest VLAN 999 but when i apply the ACL on the Guest Interface created on the WLC, I dont see any pings going across and neither I see any hit counts on the deny statement as if the ACL is never applied.
I've got router as vpn-concentrator which receives vpn site-to-site connections from 10 branches with cisco 881 and cisco 1941.I started cacti monitoring and found out that there are too many errors on interfaces.URL.
View 5 Replies View RelatedAny info concerning the installation of CW LMS 4.0.1 on Solaris 10!
The installation keeps on failing when it is checking for packages. Also the second time when we downloaded the software once more.
ERROR: AddProperty called with invalid package name: CSCOmd.
I have also attached the install log files.
The system is Solaris 10 with zones:
bash-3.00# more /etc/release
Solaris 10 10/09 s10s_u8wos_08a SPARC
Copyright 2009 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to license terms.
Assembled 16 September 2009
121133-02, 125503-02, 126897-02, 127127-11, 127755-01, 138866-01 Incompatibles:
[Code] .....
I am seeing a lot of the following showing up in the WLC trap log:
Decrypt errors occurred for client <CLIENT-MAC> using WPA2 key on 802.11b/g interface of AP 00:17:0f:81:ad:90
we are using WLC runninn 7.0.98 and ACS 4.0
I am installing LMS 4.1 to windows 2008 R2 SP1.Server hardware meets requirements.A the end of the installation I am getting from the installation log file the following warnings/errors. [code]
View 5 Replies View RelatedHow can I troubleshoot, what can I do if we get poller errors in HUM suddenly? It was running some days only.Its an installation in our solution center and Im in comparing the results with Cacti and Nagios/PnP - there is no problem at the same device and interfaces with this tools.
SCSwitchB
#
MIB VariableInstanceFailure StatusFailure CountLast Failed ReasonLast FailedifHCInOctetsGi3/2Permanent458No Such Instance - The specified instance is not availableMon, Jul 18 2011, 22:02:01 CESTifHCOutOctetsGi3/2Permanent458No Such Instance - The specified instance is not availableMon, Jul 18 2011, 22:02:01 CESTifHCOutOctetsGi3/3Permanent458No Such Instance - The specified instance is not availableMon, Jul 18 2011, 22:02:01 CESTifHCInOctetsGi3/3Permanent458No Such Instance - The specified instance is not availableMon, Jul 18 2011, 22:02:01 CEST
I have installed WCS 7.0 now i have installed Navigator on WCS server.Installation is completed.but when I check the status of WCS, it says "healthmonitor running with errors"any one knows what could be the problem and how much will that effect on WCS performance?
View 6 Replies View RelatedNo date in the TOP-N Interface Errors portlet showing in LMS 4.1, but data for TOP-N Interface Utilization is displayed like expected. The Interface Errors poller show active(without errors) with same Instances as Interface Utilization.
View 1 Replies View RelatedI am receiving allot of Errors "%ASA-4-405001: received ARP collision from IP/MAC on interface dmz1 with existing ARP Entry IP/MAC
When i checked this MAC address in the same firewall it shows too many IP Addresses. What could be the reason ?
I am looking at the interface stats of port Fa1/0/2 and see something strange. Ouput drops are 42Billion in 16mins, then 21249 few seconds later, then followed by 42Billion drops again, then 21444...and so forth..I keep getting an entirely different output drops reading everytime i refresh within seconds of each refresh!
sh int fa1/0/2
FastEthernet1/0/2 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is ecc8.8266.d604 (bia ecc8.8266.d604)
Description: MSGMERGF1
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 12/255, rxload 11/255
[code]....