Cisco WAN :: Output Errors On 3750 Switch?
Jan 31, 2012
I am looking at the interface stats of port Fa1/0/2 and see something strange. Ouput drops are 42Billion in 16mins, then 21249 few seconds later, then followed by 42Billion drops again, then 21444...and so forth..I keep getting an entirely different output drops reading everytime i refresh within seconds of each refresh!
sh int fa1/0/2
FastEthernet1/0/2 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is ecc8.8266.d604 (bia ecc8.8266.d604)
Description: MSGMERGF1
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 12/255, rxload 11/255
[code]....
View 3 Replies
ADVERTISEMENT
Sep 13, 2011
I have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G
Total Output Errors 0 47749
Small Buffer Misses
4 misses
139 misses
[code]....
View 1 Replies
View Related
Jul 13, 2011
EEHYP_CS_801#sh logging Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: disabled
Monitor logging: level debugging, 236 messages logged, xml disabled,
filtering disabled
[Code].....
View 5 Replies
View Related
Mar 13, 2013
One of my Catalyst 3750 switch have many out drops, I execute "sh mls qos int g2/0/3 statist" command, there are many output drops in queue3 threshold3. [code]
View 8 Replies
View Related
May 11, 2011
My router, a Cisco 7204 with NPE 300, is experiencing output drops and input errors on a fastethernet interface. I have a 100Mbps connection with less than 15Mbps utilization at peak times.
FastEthernet1/0 is up, line protocol is up Hardware is DEC21140, address is 0014.a985.1a1c (bia 0014.a985.1a1c) Internet address is 38.102.66.134/30 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 3/255, rxload 1/255
[Code]....
View 17 Replies
View Related
Jan 9, 2012
today I witnessed a cisco n5k that stopped playing fair. For a yet unkown reason several interfaces started to show output errors all begining within the same second. While i instantly thought this would be a wiring issue I began to ask myself what an output error actually means. Google usually brings up output drops, not regular output errors. So what is it and how can a 10G fiber interface even detect that there is a problem without receiving what it was sending?
View 2 Replies
View Related
Jun 6, 2012
We are facing output queue problems on our ATM interfaces. A lot of output queue errors are been shown as below.
Cisco 2811 -> ATM Link -> <-ATM Link <- Cisco 3945 Routers.
Cisco 2811 Version is 124-15.T9.bin
Cisco 3945 Version is SPA.150-1.M1.bin
Cisco 2811 Output Errors
View 3 Replies
View Related
Nov 17, 2012
I have seen an error in GRE configured between two routers over WAN. i am monitoring the WAN link and GRe tunnel via WhatsupGold NMS and it reported that Gre tunnel having packet loss sometimes and this time it affects the services and traffic passing over tunnel.sh int t101 shows output drops . is that the problem ? i have read that i have to adjust MTC size but i tried to change the tunnel MTU to 1400 but still sh int t101 shows MTU as 1514 ? What could be the problem of output drops in my tunnel link. [code]
View 1 Replies
View Related
Apr 16, 2012
I've been working on breaking down and understanding the default auto qos configuration on a Cisco 3750 in the hopes of putting together a QoS strategy that will fit our environment. I'm having some difficulty understanding how the "mls qos queue-set output" syntax works.
From another post, at [URL], the author offers the following example and explanation;
mls qos queue-set output <1/2> threshold 2 400 400 100 400thresshold 1: 400%
thresshold 2: 400%
thresshold 3: 100% (implicit, not configurable)
reserved: 100%
max: 400%
However, I'm having trouble understanding what is meant. Here, it looks like it's saying, for example;
mls qos queue-set output 1 threshold 2 400 400 100 400
How come there is syntax stating "threshold 2" when in the succeeding part the 400 refers to thresshold 1 and threshold 2 again? The syntax 400 400 is, apparently, already referring to thresshold 1 and 2, no?
View 1 Replies
View Related
Dec 4, 2012
We have a 100Mbps metro-ethernet link connecting to a remote site. This link is terminating in our 3750-x stack switch.We are getting a LOT of output drop on that interface and our remote IP Phone calls keep going off because of that.I've disabled all kind of QoS, but no luck.
View 16 Replies
View Related
Sep 28, 2011
Am not finding the resolution to my infrastucture and getting output drops. Sw1 is connected Sw2 as below stated
Please find the conf:
Sw 2 3750 conf:
interface GigabitEthernet1/0/46
no switchport
ip address 172.16.100.81 255.255.255.248(code )
View 5 Replies
View Related
Jan 26, 2009
I have a 3750 switch (c3750-ipbasek9-mz.122-46.SE.bin) were i want to add bandwitdh limit pr. interface, doing the following:
ip access-list extended customer_A
permit ip any any
class-map match-all BW_10Mbps
[Code]....
When i trie to apply the "service-policy output 10 Mbps" to the interface, it says the service-policy output is not supported on the switch. Is this a software related isue ?
View 4 Replies
View Related
May 15, 2011
I am seeing Interface output drops that appera to be incorrect. When I do "Show Interface gi1/0/20", I will get interface output drops of "4294961382". But, when I do the same command again it shows "0" drops. Is this a reporting error? I am ruinning c3750-ipservicesk9-mz.122-58.SE.bin on a 3750 stack with 2 switches in the stack. [code]
View 10 Replies
View Related
Feb 16, 2012
When configuring QoS on 3750s/3560s, we're mapping packets to particular interface output queues with commands such as: [code] The command to see what's actually being enqueued, dropped, etc. is: [code]
Note that these queues are numbered 0 - 3, and not 1 - 4. We've been assuming that the first queue number in the "mls qos" (i.e., 1) command maps to the first queue (i.e., 0) in the "show mls qos" command.
View 1 Replies
View Related
Jun 22, 2012
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies
View Related
Dec 14, 2011
I have a PIX 535 connected through OFC to Cisco 2960 Switch.
PIX end - G0 (SC type Connector) - Switch End - Gi1/0/28 (LC type connector)
When I am pinging from either side, I am getting packet drops. CRC error is increasing at PIX interface.
Speed settings, tried with
auto - auto
auto - nonegotiate
nonegotiate - auto
nonegotiate - nonegotiate
But no improvements. When its connected with SC - SC connector, its working fine.
Switch also working fine when connected LC - LC.Switch OS is 15.x version.
Cisco PIX Security Appliance Software Version 7.0(4) <system>
Device Manager Version 5.0(4) Cisco PIX Security Appliance Software Version 7.0(4) <system>Device Manager Version 5.0(4)
View 1 Replies
View Related
Feb 7, 2011
I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
View 9 Replies
View Related
Jan 10, 2013
I've been fighting what seems to be an increased number of outqueue drops on our core stack and edge switches for the last 3 or 4 weeks.(The core consists of a stack of 5 3750s in 32-gig stack mode. The wkgrp switches are 3560s. all are at 12.2.52) The wkgrp switches are directly connected to users. We use Nortel IP phones with the phone inline with the user PC. auto-neg to 100/full. [code] However I have tried turning off QOS on a couple of workgroup switches (no mls qos, but left individual port configurations the same) but am still seeing drops.Since I have disabled qos on the switches in question (no mls qos) (not the core tho) I am presuming these commands have no affect on the switch operation and therefore cannot be related to the problem. With QOS turned off one would presume that it is general congestion - especially at the user edge where busy PC issues might contribute. So I wanted to see if I could see any instances of packets in the output queues building up.
I wrote some scripts and macros that essentially did a snapshot of 'show int' every 20 seconds or so, and looked for instances of 'Queue: x/' where x was greater than zero.What I found after several days of watching the core stack, and a few of the workgroup switches that are most often displaying the behavior, was that I NEVER saw ANY packets in output queues. I often saw packets in Input queues for VLAN1, once in a great while I would see packets on input queues for fa or Gi interfaces, but NEVER on output queues. [ code] Additionally, when I look (via snmp) at interface utilization on interfaces showing queue drops (both core and wkgroup), they are occurring at ridiculously low utilization levels (as low as 4 to 8%). I've tried to look for microbursts between the core and a wkgroup switch where the core interface was experiencing drops, but haven't seen any (using observer suite). [code] While the queue-drop counts aren't critically high at this point, they are happening more frequently than in the past and I would like to understand what is going on... In most cases, no error counters are incrementing for these interfaces. Is there some mechanism besides congestion that could cause output queue drops?
View 4 Replies
View Related
Oct 6, 2012
I have 2 cat3524xl's and a 3550. I recently did something to the IOS that makes the switch not display any output to the console port. Not sure what I did but even doing the reset as instructed in the Cisco docs by holding the mode button foe 2 seconds after boot. I get the flashing green light but still no output. All POST tests pass according to lights so I tried different cables and all baud rates with no change. I hoocked switches back up in lab and can see them in CDP neibors but do not know how to access them from there as they have no IP assigned to them. Remember this is two of them with exact same issue.
View 2 Replies
View Related
Jul 4, 2011
I have a 48 port 2960 switch with 2 10/100 ports ( fa0/46-47) setup in an etherchannel with a 2950 48 port switch. I am getting total output drops on port fa0/47. [code]
View 2 Replies
View Related
Jan 10, 2012
Sometimes our network lag and i thing there is a computer making this problem. i'd like to audit all input output of all port of a Catalyst 1900. all i manage to do is to enter to the console menu via Telnet.. once here, i try monitoring but i'm afraid to do a bad thing :
Catalyst 1900 - Main Menu
[C] Console Settings
[S] System
[N] Network Management
[P] Port Configuration
[Code]...
View 2 Replies
View Related
Apr 15, 2010
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
View 16 Replies
View Related
May 19, 2013
SW1#show interfaces fastEthernet 0/14 counters errors
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
Fa0/14 6682 140364 0 306468 0
Port Single-Col Multi-Col Late-Col Excess-Col Carri-Sen Runts Giants
Fa0/14 0 0 0 0 180103 0 2798
[code]....
View 5 Replies
View Related
Apr 29, 2011
On my D-link routher the power supply broke. I instal another one but it has 2.5A as output instead of 2A as the broken one has. Is it dangerous.
View 2 Replies
View Related
May 22, 2012
What is the cause of having a huge number ( 875349) of total output drops on one of my gigabit utp port gi 2/12 which is connected to Cisco 1841 fa0/0 router by mean of cat5e cable.I did change the cable from cat5e to cat 6 and tried to increase hold queue to 4096 and to tweak wrr queue bandwidth
View 4 Replies
View Related
Feb 26, 2012
what's the meaning of the output:
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi0/40 100M Pair A 2 +/- 4 meters Pair A Normal
Pair B 2 +/- 4 meters Pair B Normal
Pair C 2 +/- 4 meters Pair C Short
Pair D 2 +/- 4 meters Pair D Short
From the command
test cable-diagnostics tdr int gi 0/40
It's normal?If not, then. the problem is on the cable or on one of the interfaces?The interface is connected between a fastethenert on a 2811 router and a 3560-48 switch.The cable is a straight through cat 5e cable. (I have changed several cables with same result).
View 4 Replies
View Related
Feb 11, 2013
I just got a Cisco 2960G 24-port gigabit switch so that our HP servers can have a Gigabit connection to the network. I moved 2 servers to it (HP Proliant DL380's) but they don't actually seem to be able to achieve even close to 1000Gbps. I ran same some LAN bandwidth tests and it was showing only around 200-300 Mbps between all of them. I also ran a network stress test utility, LAN Tornado, and it was showing packet loss as high as 60% when on gigabit, and only .07% when on 100Mbps.
-Both the NIC's and the switch ports are set to 1000/Full
-Currently using Cat5e cabling no more than 25Ft in length (I know Cat6 would be better but Cat5e is supposed to support Gigabit)
-All servers are on the same VLAN
Here are the port statistics when running just a stress test @ 10Mbps that had a 45% packet loss. What's odd though is when I set the servers and switches to 100Mbps, I get less than 1% packet loss.
GigabitEthernet1/0/16 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 203a.07ff.7e90 (bia 203a.07ff.7e90)
MTU 9000 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
[Code].....
View 2 Replies
View Related
Jan 16, 2012
this router of my girlfriends only works when iplug the dsl modem into the output ports what could possibly cause this. would a firmware upgrade straighten it out...
View 1 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Nov 18, 2012
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies
View Related
Nov 10, 2012
I have a 3750 switch.The status of the switch is rommon," switch : ".there is not an IOS in the switch....Are there ways to install an IOS excepted xmodem
View 6 Replies
View Related
Feb 1, 2011
I need to use a 3750 switch running 12.2 code to route between two networks in a test setup.Switch#sh verCisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2006 by Cisco Systems, Inc. The idea for the test setup is 3750 emulates a client's live network which is two routers having a site-to-site tunnel connecting from their ISPs. This will allow me to test the tunnel configuration with the router configs that are in production but replacing one of the routers with an ASA.
View 3 Replies
View Related
Jun 8, 2011
I have some client with Anyconnect 3.0 configured .I want that all traffic (vs. LAN and vs. Internet) is tunnled in the SSL VPN. On the ASA i configured a route that all traffico tunnled goes to Switch 3750. route inside 0.0.0.0 0.0.0.0 192.168.80.229 tunneled The switch ahve this configurtion for the routing
ip default-gateway 192.168.80.228
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.80.228
But if i have a pc that have default gw the switch ip 192.168.80.229 all works fine, but the client vpn have a problem that can't go to internet.I attach a schema and a configuration.If i try to navigate only through the ASA with the client VPN all works. But if i try to tunnle the von traffic to the switch and come back to the and then to internet all stop to works.
View 1 Replies
View Related
