Cisco :: Switch 3750 Without IOS
Nov 10, 2012I have a 3750 switch.The status of the switch is rommon," switch : ".there is not an IOS in the switch....Are there ways to install an IOS excepted xmodem
View 6 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3750 / 3800 - Configure Trunk Between Switch And Extreme Switch
Nov 2, 2011i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedCisco Switching/Routing :: 3750-X Stacking Switch By Switch
Nov 18, 2012I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedCisco WAN :: Using A 3750 Switch To Route
Feb 1, 2011I need to use a 3750 switch running 12.2 code to route between two networks in a test setup.Switch#sh verCisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2006 by Cisco Systems, Inc. The idea for the test setup is 3750 emulates a client's live network which is two routers having a site-to-site tunnel connecting from their ISPs. This will allow me to test the tunnel configuration with the router configs that are in production but replacing one of the routers with an ASA.
View 3 Replies View RelatedCisco WAN :: Output Errors On 3750 Switch?
Jan 31, 2012I am looking at the interface stats of port Fa1/0/2 and see something strange. Ouput drops are 42Billion in 16mins, then 21249 few seconds later, then followed by 42Billion drops again, then 21444...and so forth..I keep getting an entirely different output drops reading everytime i refresh within seconds of each refresh!
sh int fa1/0/2
FastEthernet1/0/2 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is ecc8.8266.d604 (bia ecc8.8266.d604)
Description: MSGMERGF1
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 12/255, rxload 11/255
[code]....
Cisco VPN :: 3750 / ASA Tunneled Traffic With Switch?
Jun 8, 2011I have some client with Anyconnect 3.0 configured .I want that all traffic (vs. LAN and vs. Internet) is tunnled in the SSL VPN. On the ASA i configured a route that all traffico tunnled goes to Switch 3750. route inside 0.0.0.0 0.0.0.0 192.168.80.229 tunneled The switch ahve this configurtion for the routing
ip default-gateway 192.168.80.228
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.80.228
But if i have a pc that have default gw the switch ip 192.168.80.229 all works fine, but the client vpn have a problem that can't go to internet.I attach a schema and a configuration.If i try to navigate only through the ASA with the client VPN all works. But if i try to tunnle the von traffic to the switch and come back to the and then to internet all stop to works.
Cisco :: 3750 Switch Time Zone Off
Apr 28, 2013some of my switches (3750s) are on the right time and some are not. i have them all pointed to the same DC for NTP and they all say they are synchronized. is it possible to have the switches pole the DC for the right time and update?
View 4 Replies View RelatedCisco WAN :: Dot1x Authentication On 3750 Switch?
Jan 18, 2010I have 3750 switch (WS-C3750G-24TS-S1U) with IP Services version
Switch Ports Model SW Version SW Image------ ----- ----- ---------- ----------* 1 28 WS-C3750G-24TS-1U 12.2(46)SE C3750-IPSERVICESK9-M
on the switch, I have configured aaa new-modelaaa authentication dot1x default group radius dot1x system-auth-control but i am not able to implement the command under interface
Switch(config)#int gigabitEthernet 1/0/20Switch(config-if)#do?down-when-looped
dot1x commands are not available under the interface config. Is the IOS version is compatible with dot1x?
Cisco AAA/Identity/Nac :: ISE & 3750 Switch MAB Configuration
Jan 16, 2013I am writting in response to MAB issue which I noticed a few days ago and I am still not able to undestand what exactly happend. First of all I would like to say that I configured MAB authentication and according to the MAC the ISE configure a VLAN. All worked well: the test computer can change VLAN based on its MAC. The problem appear when I cut the connection to ISE server. Accourding to configuration the switch authorize the new device to VLAN 11 (critical VLAN) That is fine ! When the ISE server is up again I had a configuration which should reauthorize all ports assign in critical VLAN. But why that is not happend ??? It looks as the switch didn't notice that the RADIUS (ISE) was up and working again. [code]
View 1 Replies View RelatedCisco LAN :: Four Member Switch Stack 3750
Apr 16, 2013We have a current 3-stack 3750 ( 48-P,48-TS & 3750v2-48PS ) running fine. There is a plan to introduce a fourth stack member ( 3750X-48P ) into this stack.as per cisco documentation, it suggests to use 3750X as master for a mixed stack. In this case, we will need to upgrade current other 3 stack switches to a latest version.,Can we do a no-downtime ios upgrade on the existing 3-switch stack?, when this upgrade is done, is there any way to have the new ios pushed down to all three stack members at the same time or do we need to each member upgrade seperately?, for adding the fourth member, is it acceptable if master is ruuning ver eg. 12.2(55) and all rest of the members run ver 12.2(53) ? will this create any issues and will stacking be successful.
View 5 Replies View RelatedCisco WAN :: 3750 - Move Configuration From One To Another Switch?
May 20, 2013im trying to move the config from an 3750 to 3750 PoE but without using the PoE options.I have allready download the config with tftp and upload it to the 3750 PoE. Now the new config is stored on the PoE switch but some of the old setting are still there. Not sure why, i think the config only overwrite the settings which are in the conf file and the setting which are not in the conf file but enabled on it will stay on the switch.After the upload of the config file I deleted all the config I do not need by hand.They are some settings i can't delete and I don't know why, this are the sittings:
1. each fastethernet port has this option: "no cdp enabled" this entry was no availble on the old switch, is the any possiblity to remove this entry?
2. the same for "no mls qos rewrite ip dscp"
3 and for this one "vlan internal allocation policy ascending"
Cisco Wireless :: 3750 - QoS Configuration In Switch For AP And WLC
May 6, 2013The access swtich is a Cisco 3750 and the Core switch is a Nexus 5000 series. I am configuring the switchport were the AP (3502) and WLC (5508) is connected below:
For AP: interface GigabitEthernetX/XX
switchport access vlan 244
switchport mode access
[Code]....
The WLC is connected to the Nexus switch and it is not accepting the 'mls qos trust cos' command.
Cisco WAN :: QoS Configuration For 3750 Switch WAN Port?
Jul 27, 2011We are using 3750 switches as WAN router facing the WAN cloud. To configure QoS for its WAN port, should I use 'auto qos voip trust" or treat it like a router port and configure class-maps, policy-maps, and attact service-policy input or output?
Because switches have different queuing and dropping methods than routers, auto qos can generate QoS configs that are considered most appropriate for 3750 switches. However the switch functions as WAN router. Maybe it should be configured using router type of QoS with policy-maps and service-policy?
Cisco AAA/Identity/Nac :: 3750 - Cannot SSH To Switch 2960
Jan 10, 2012I replaced an access switch 3750 with a switch 2960. Basically I just copy the whole config of the 3750 to 2960.
The 3750 use AAA, Crypto pki trustpoint TP-self-signed and radius-server host etc.
Now I can only telnet to 2960 but not SSH to it.
Cisco WAN :: Setting Up Password On 3750 Switch?
Jan 23, 20121. set up password on a new cisco 3750 switch
2. steps to recover a lost password.
Cisco WAN :: 3750 - Stack And Switch Port Keeps Going Up / Down
Nov 7, 2012I have 2 3750x switches connected via a pair of stackwise cables, but I keep seeing error messages about the stack&switch ports going up and down,Performance wise, it seems to work, but I'd like to eliminate this message... Sometimes it will go hours without bouncing, sometimes it does it a few times a minute....
*Mar 4 12:56:57.903: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN
*Mar 4 13:16:48.070: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 2 has changed to state UP
*Mar 4 13:16:49.093: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 2 has changed to state DOWN
*Mar 4 13:38:55.802: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state UP
*Mar 4 13:38:56.809: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN
[code]...
Cisco LAN :: 3750 Switch To Juniper Firewall
Oct 6, 2012We have a 3750 as core switch with critical oracle servers ( production & development ) connected to this. The goal is to have these servers behind a firewall, which is to be done by logically routing the traffic towards the device.Now, we need to connect the 3750 with two juniper srx firewall physically. The oracle server VLAN will be removed from 3750 and same layer 3 vlan will be created in the juniper firewall. How do i connect the 3750 to the two junipers. what configurations will be involved, on a logical basis.
View 11 Replies View RelatedCisco :: 3750 Switch - Connectivity Lost For Some Ports?
Mar 8, 2013In my 3750 stack switch there are more than 10 L3 vlans currently in use.In that only one vlan for example vlan 11 (we given up link directly to the nodes connected to that ports which is in vlan 11)losing connectivity for sometime and again connectivity restored.Except Vlan 11 all other vlans are working fine. When we troubleshooted the issue some of the ip's able to ping and some not able to ping. checked the interface status of that ports (no crc and input errors) and port is in up status only.we also checked cpu utlilisation ,device uptime, all are no issues found. am sharing my sw basic config and one interface status at the time of issue.But only one port learning more than 50 Mac-Addresses dynamically.and am learning mac address violation in another port which is port security and storm control enabled on that port..Its seems to be any attack or something else????
interface GigabitEthernet1/0/20
--More-- description
switchport access vlan 11
switchport mode access
spanning-tree portfast
logs:
Mar 8 05:58:25.848 IST: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0026.0a18.8218 on port GigabitEthernet1/0/16.
Mar 8 05:59:25.862 IST: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0026.0a18.8218 on port GigabitEthernet1/0/16.
AT the time of issue interface status:
sh int gi2/0/14
GigabitEthernet2/0/14 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0026.ca46.5c8e (bia 0026.ca46.5c8e)
Description:
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,[code]......
Cisco WAN :: 3750 AAA ACS And Switch Lockups Cannot Console Onto The Switches
Jul 9, 2012We are having a problem with our ACS and switch configuration.Basically if the switches lose connectivity to the ACS server the switches completely lock up, you can’t even console onto the switches.We want them to use the fall back username and password when this happens.
View 1 Replies View RelatedCisco Switching/Routing :: Configure QOS In 3750 Switch?
Nov 7, 2011configure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies View RelatedCisco Switching/Routing :: Switch 3750-X Vulnerability
Jul 19, 2012I had a bad expirience with Switch 3750-X. Because of an auditing security processess, my customer ran a software called "Nessus" to do a scanning of vulnerability on the network. When this software is point to switch, the process of the switch will next to 100% and reset. The software only do a listening on the ports to see what ports are opened and the switch should not reset because this. Bellow is the log os switch on the moment of test; we note that the processess 'HTTP' rise moments before the switch reset. I disable the HTTP service on switch but the problem persist. The test was made only one machine connected to switch.
View 4 Replies View RelatedCisco Switching/Routing :: 3750 POE Switch Stacking?
Aug 12, 2012We have three Cisco 3750 - 48port POE -LAN switches and i am trying to see if there are any issues when we stack POE and Non-POE type of switches.Aslo looking for information on the advanatage and disadvantage the stacking can provide on a Cisco 3750 48port.
View 3 Replies View RelatedCisco WAN :: 3750 ME Switch Getting Error Message After Restart
Aug 28, 2011I am using 3750 ME switch and we have restarted the switch 7 weeks age and we are getting error message, we are using MPLS / BGP in this switch.
View 1 Replies View RelatedCisco Switching/Routing :: Setting MTU On A 3750 Switch?
Dec 12, 2010The question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
Cisco Switching/Routing :: Remove QOS From 3750 Switch
Jun 8, 2007How do you properly remove the QOS queues and configs from the switch.A was using auto qos which created a whole mess of qos configs on my running-config. I did "no mls qos" in conf term but that did not remove the queues.
View 3 Replies View RelatedCisco Switching/Routing :: 3750 / Add A New Switch In Stack?
Jun 21, 2012i want to remove an access layer 3750 48 POE master switch and replace with a new 3750 switch in the stack. i want to copy the same configuration to new switch since the old switch is having POE issue and I got replacement of the malfunctioned switch. we have VTP domain is configured in the network...
View 3 Replies View RelatedCisco Switches :: Possible To Trunk SF300 With 3750 Switch
May 4, 2011Is it possible to trunk a SF300 switch with a 3750 switch? If so how? Whenever I turn trunking on the 3750 port I lose connection to the SF300.
View 5 Replies View RelatedCisco WAN :: No IOS - Cannot Access Multilayer Switch (catalyst 3750)
Sep 10, 2011Working on my CCNA w/ live equip, I accidentley deleted the hardware IOS- yes, beginners mistake. Upon bootup, I do not get a command prompt. I tried the recovery procedure(hold mode button before power up) recommended by Cisco to no avail. My issue is I use SecureCRT & the charaters/font is ineligible. Here is an example of what I see when typing; "þæb Bûÿÿûýÿ¿¿ÿÿ". Currently, the SYST indicator is blinking & I have no access.
View 3 Replies View RelatedCisco WAN :: 3750-X POE Power Is Not Coming On Switch Port
Feb 22, 2013We have configured Cisco 3750X POE series switchs with Stack.WS-C3750X-48P each with Redundant 1100W & 715 W PSU's. They are configured with Stack-Power in Sharing mode and the switches are Smart Stacked as well.IP Phone and Access points are connected its working in last two years,
Now we are facing some issue on Cisco IP Phone and Access point, When i have problem if unplug (disconnect & Reconnect) the IP Phone from Switch port,Power is not comming on switch port.Plug it into another switchport of the same Switch it may not power in any port.I tried shut & no shut and reconfigured on switch port , I have verified multiple switch ports same issue on the switch I have changed cable.
Cisco WAN :: 3750 - Getting Error On Enabling IP Routing In L3 Switch
Nov 5, 2012I am really stuck in enabling ip routing though a simple task. I have configured 10 v LAN's in stacked 3750 switches have ip base image. I want to enable ip routing for inter V LAN communication but it is giving this error:
%COMMON_FIB-4-ISSUENCODEWRONGLEN: Message IPv6 global features, rev B for slots 2 (0x4) is wrong length (10, should be 7).
Cisco WAN :: Catalyst 3750 - Adding Switch To Stack
Mar 23, 2012I have a Catalyst 3750 I want to add to an existing stack (same models) through the stackwise port We use some complex QoS and other features on our network, and I'm not sure how much configuration I need to do on the new switch before adding it to the stack. Since this is going into an existing setup?
View 9 Replies View RelatedCisco Switching/Routing :: 3750 - Cannot Communicate With Switch
Sep 11, 2012Cisco 3750, I'm trying to reset the password but cannot communicate with my switch
View 1 Replies View RelatedCisco Wireless :: Connecting WLC 2504 With 3750-x Switch?
Aug 15, 2012I connected my 2504 wlc with my 3750-x switch using port-channel. Later i came to know that LAG mode is not supported in 2500 series , so i removed port-channel from my core switch and connected all the 4 port in WLC to core without any port-channel. Is that recommended?
one more thing is , from WLC i can ping tha management interface on my core. but i cannot ping the default-gateway of my dynamically created interface on my WLC to core(core is the defauly gateway for all).