I have ASA5540 with asa712-k8.bin.
There is a plenty of tunnels ended and it works.But i have one tunnel, which doesn't work.I tried turn on "debug crypto isakmp" and it show this: RECV PACKET from 10.200.79.161 ISAKMP Header. [code]
So there is problem with IPSEC and with no matching SA, but i don't know which one.Then i try to turn on "debug crypto ipsec 255" but it displays nothing. [code]
I just installed this DIR-825 router and when I look for an available network the only one that comes up is the 2.4. No 5.0 at all.
View 5 Replies View RelatedI have a Cisco 1800 ISR router running IOS 12.4(22)T5.Clientless SSL VN is configured and working, and has three bookmarks.When logged into Clientless SSL VPN and displaying the portal page in IE-8, the bookmarks are visible and functioning as expected.When logged into Cleintless SSL VPN and displaying the portal page in FireFox-14 or Chrome-21, the bookmarks are not visible.The window for the bookmarks is displayed, but the content (file tree) is not.
View 1 Replies View RelatedWhen I went to the cmd prompt and typed in ipconfig/all I got...
Ethernet adapeter Wireless Newtork Connection 4:
Description- Dell Wireless Mini Card
Physical Address-00-1E-4C-05-99-B3
[Code].....
I have turned on the aaa command authorization without applying adequate privileges to the user. I can now log in through that user but the ASA 5510 displays an error :ASA 5510# show running-config
ERROR: % Invalid input detected at '^' marker.
ERROR: Command authorization failed.
I am unable to make any configuration changes on the firewall. Is there any default user through which I can log in and disable the aaa authorization ? if not, how can I resolve this situation ?
My EA4500 with the latest firmware will only display nine connected devices at a time. It also seems to randomly shuffle which devices to show as connected, even though several more than nine are connected and online. Does anyone else's device list limit itself to displaying only nine devices? The Linksys phone apps also display a maximum of nine devices. I like the routers new user interface and understand that it has received a lot of praise, however this is the second bug I've experienced in as many months (the first being a failure of the device list to update once devices are upgraded to Windows 8, requiring a reset to default settings in order to fix).
View 5 Replies View RelatedWhy does the sx300 series only displays ping and traceroute results in 20ms intervals (see below)? The example in the CLI manual shows "regular" results. These 20ms intervals are not useful for troubleshooting. This is version 1.1.0.73 on an sf300-24. [code]
View 2 Replies View RelatedMy E4200 settings show both the 5.8GHZ and 2.4GHZ channels to be active, with SSID's displayed. However, when I look for available networks via my laptop(s)/tablets, etc, only the 2.8GHZ channel is visible. I've tried changing various settings and even updated the firmware but nothing has changed.
In addition my "guest" portal displays as not being password protected, even though it is setup for password protection in the E4200 menu.I've rebooted the router several times, but nothing has changed. The 5.8GHZ channel is not visible.The router is also performing frequent random disconnects, but that appears to be a separate issue, based on other posts.
when tryin to install new WLAN driver of the following details from dell website wit my service tag WLAN half mini card 1501 it displays no compatible hardware found
View 2 Replies View RelatedLinksys WRT610N displays garbage when accessing the "Wireless Page" in Internet Explorer (from Windows 7 or Windows 8)My issues is simmilar to one reported here: url...Accessing my Linksys Wireless Router model WRT610N using IE opening "Wireless" page displays full screen of garbage characters (looks like chinese).
View 2 Replies View RelatedI just installed my new E4200, and am setting the Access Restrictions. Is there anyway to block the popup window that displays every time I enter the form or save the settings?
I'm using IE9 and have tried adjusting the Popup Blocker, but to no avail.
i have 3 access-list configured IN | Out on my Border router (MARTIAN) ,i have to look which one block some of the traffic passing through ,for that matter i have enabled the below commands on my ISR 2900: with nothing output.
View 3 Replies View RelatedMy tunnel had been running fine for a couple of months. Now, not so much.Here is some debug.
View 6 Replies View RelatedI have been using "debug ip packet" on a Cisco 2921 running IOS 15.1(4)M1. The problem I have is that, although I am using an ACL to limit the output, I am seeing some output that is distracting from what I am trying to see. Specifically, I am seeing the following:
Mar 19 20:22:36.135: IP: s=192.168.20.253, d=224.0.0.2, pak 30DB6D4C consumed in input feature , packet consumed, MCI Check(80), rtype 0, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
[ code]...
These would appear to be HSRP messages. But I don't understand why they are appearing when I configure "debug ip packet 101". The ACL is pretty simple:
access-list 101 permit icmp host 96.87.145.1 host 192.168.20.1
access-list 101 permit icmp host 192.168.20.1 host 96.87.145.1
So I thought the implicit "deny ip any any" would block these messages. I even tried to block them specifically using an extra line:
access-list 101 deny udp host 192.168.20.253 host 224.0.0.2 eq 1985
But still they show up!
Is there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies View RelatedUsing 'debug ip packet acl# det on a 2911. On an older Cisco router you could set up an ACL
access-list 150 permit tcp any any eq 1023 and then run debug ip packet 151 det and this would give a good debug output for any traffic matching a TCP port of 1023.Now when I try this on a 29xx ( Version 15.1(4)M3 ) I get the screen filling with a lot of multicats HSRP communications.
I have tried rewriting the acl to have other deny statements after the permit to limit the source or destination hosts and/or the ports but the HSRP data is still there.
like this
access-list 150 permit tcp any any eq 1023
access-list 150 deny udp any any eq 1985(code)
how to debug an ACL I've created on a 4404 WLC, specifically I want to monitor what packets are being denied by the ACL as something that should be working isn't
I've created an explicit deny statement at the end of the ACL and verified that the counter increases each time I try the problem software update.
What I can't work out is how to get the WLC to tell me what packets are being denied by the explicit deny statement, all I can find are 'show acl' commands which just give me the counts.
The equivalent on a router would be debug ip packet acl and adding the log keyword onto an ACE. I suppose I could configure a SPAN session on the WLC uplink to the switch but that seems overkill?
Iam fairly new to Cisco IOS and am having trouble getting an IPSEC tunnel to come up between 2 cisco 881-s. I have entered both debug crypto isakmp and debug crypto verbose but when I try to ping an internal IP at the other location through my VLAN1 interface no debugging info comes up.
Also my ACL-s for the crypto maps show no activity. I have tried many things so my configuration files are starting to get really messy.
[code]...
I'm attempting to debug an ipsec tunnel on an ASA 5510 (8.4(3)) and when I turn on `debug crypto ipsec` and then execute `logging monitor` I get an constant stream of TCP debugging events, is it possible to only view ipsec messages?
View 2 Replies View RelatedDebug is not showing up on the console. I have configured logging console. My older switches, if an interface goes down or is brought up, it shows up on the console, but not on the new 4507s.
WS-C4507R-E
cat4500e-ipbase-mz.122-53.SG2.bin
TG-4507#sh loggingSyslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
[code]....
I have this situation, I need to establish an IP sec communication to another site but I need to identify all my packets sent, as a different networks as my local one. for example: my local network is 10.5.0.0/24 and I need to sent packets as 10.6.0.0/24. I suppose that I need to do Nat with this IPs. But in this router Nat is already applied to outbound traffic to Internet. How can I apply this NAT to crypto map only?
My router is a Cisco 877 with 12.4 IOS an this is the relevant configuration, crypto map vpn it´s used to sent traffic to second site.
crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxxxx address XX.XX.XX.XX
crypto ipsec transform-set vpn esp-3des esp-sha-hmac
crypto map vpn 1 ipsec-isakmp set peer XX.XX.XX.XX
[ code]....
I'm troubleshooting one way audio with our anyconnect phones.I think it is a routing issue.typically I wouldnt run debug ip packet detail on a production router, however I just found out that you can use acl's to specify the traffic to be debugged.
R1(config)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
R1(config)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
R1(config)#end
R1#debug ip packet 199 detail
IP packet debugging is on (detailed) for access list 199
The use of debug commands requires the allocation of system resources like memory and processing power and in extreme situations can cause a heavily-loaded system to stall. Use debug commands with care. Use an ACL in order to selectively define the traffic that needs to be examined to reduce the impact of the debug command. Such a configuration does not filter any packets.
Any way of narrowing down a degub for a peer address only? For example, I currently run 'debug crypto isakmp 127' which captures everything, but can I run the same dVPN debug for peer address 1.1.1.1?I know you can run 'sh crypto ipsec sa peer 1.1.1.1'.We're using an ASA5520 (8.4.2).
View 2 Replies View RelatedI am quite new to wireless side and had a small Q regarding watching debug output while i am ssh to the WLC? I tried the other day and did not see any messages, now this could be for the reason that nothing triggered or perhaps it needs something like terminal monitor?? i couldnt find any such command. my WLC is 5508 running 7.3 version.
View 2 Replies View RelatedWhere can I find information on using debug on the SGE2010P switches? The information in the admin and reference guides is extermely limited.
View 1 Replies View RelatedI have a 2600 with a PRI card, when I try to do an isdn test call int s1/0:23 ######### the debug constantly comes back with "Cause i = 0x83E020 - Mandatory information element missing" Vendor states he doesn't see the SDN 'flag' coming through. I have both the isdn nsf-service, and the dialer map configured to use a class with the outgoing sdn command.
View 10 Replies View RelatedI use a C892 router with the IOS c890-universalk9-mz.152-1.T.bin. I just ran the command "debug ip packet 151 detail" and then the router stopped to work because it was overloaded. The ACL151 I used is as follow:
Extended IP access list 151
10 permit ip host 10.1.1.1 host 91.1.1.1
In the syslog then I got hundred of messages from IPSec:
Jan 11 09:43:35.677: IP: s=10.80.10.254, d=10.64.19.99, pak 8A7453CC consumed in output feature , packet consumed, IPSec: to crypto engine(70), rtype 1, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
[code]....
For me it seems just like that this ACL is not applied and that I have a debug then for the whole traffic.
I have a Cisco 857 which seems to be dropping connection on its public interface.I would like to see the logs of the ppp or something which may identify the problem of why the device has lots its connection.
I know what you can setup logs for a specific IP, but it is possible to setup logs for debug messages?Also what other logs would identify the problem?
I'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?
View 1 Replies View RelatedI have to connect one of our it labors with some ec2 instances in amazon vpc. I downloaded a configuration file from amazon which starts with the command
crypto isakmp policy 200
My router tells me that he does not know crypto isakmp.
I searched on the internet and found that i have to install a specific license, but unfortunately i cannot find which license i have to install.
The show license command show following licenses
AdvIpServices active
AdvSecurity active
advsecurity_npe, ios-ips-update, waas_Express no state displayed
ssl_vpn active but eula not accepted
I found that i can accept the eula license with license boot module c880-data technology-package SSL_VPN command
But this command is also not available on my device. getting the crypto isakmp command working?
I have a 2650XM 16mb flash, 64 mb ram. 12.2(12a). now I want to buy 12.4(25d) with crypto. How much is it? And where can I buy it ?
View 10 Replies View RelatedWhat would cause debug output to not show on a remote session via telnet connection where you've enabled terminal monitor?
The reason I ask is I was working with a client and we were debugging WCCP. I ran the debug ip wccp packets and events commands, then entered terminal monitor. After this, we saw nothing. We should have at least seen particular WCCP-related packets because we saw the necessary cluster view was established which can't be done without the exchange of these packets.
Can having syslog (logging) configured cause the issue? Did I use the command incorrectly?
I've created a BVI2 where I bridged dot11 0.2 and vlan2 in order to have wired and wireless clients in the same vlan.Some wired client are not reachable from the lan. Wireless clients have no pbl in reaching each other.Monitoring a MAC address that is supposed to be behind the FA2 I have noticed that it moves to vlan2 when in fact it should be behind the FA2.Of course when "show mac-address-table" says it is behind Fa2 the ping to that MAC address works whereas when the TCAM reports it is behind vlan2 it doesn't. Once the MAC address is behind the vlan2 if I clear the mac-address-table and that mac-address is still put behinf Fa2 then the pings works again, sometime I have to perform twice the clear command before the MAC address goes back to the right location.I'd like to understand why the router moves that MAC address from Fa2 to vlan2 and that's the reason for my question in the subject.I don't have any problems for port Fa0 and Fa1."Show int fa2" doesn't show any problem/errors or the likes.BTW even if I force that MAC address to be statically behind FA2 the ping works fine but then stops and if I do "show mac-add" the static entry for it is still there... so looks like there us something that overrides that static entry. If clear everything and I have the mac-address be behind Fa2 then everything starts to work again. I used Fa3 instead of Fa2 and I get the same results.
IOS: c870-advipservicesk9-mz.151-3.T1.bin