I have been using "debug ip packet" on a Cisco 2921 running IOS 15.1(4)M1. The problem I have is that, although I am using an ACL to limit the output, I am seeing some output that is distracting from what I am trying to see. Specifically, I am seeing the following:
Mar 19 20:22:36.135: IP: s=192.168.20.253, d=224.0.0.2, pak 30DB6D4C consumed in input feature , packet consumed, MCI Check(80), rtype 0, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
[ code]...
These would appear to be HSRP messages. But I don't understand why they are appearing when I configure "debug ip packet 101". The ACL is pretty simple:
Using 'debug ip packet acl# det on a 2911. On an older Cisco router you could set up an ACL
access-list 150 permit tcp any any eq 1023 and then run debug ip packet 151 det and this would give a good debug output for any traffic matching a TCP port of 1023.Now when I try this on a 29xx ( Version 15.1(4)M3 ) I get the screen filling with a lot of multicats HSRP communications.
I have tried rewriting the acl to have other deny statements after the permit to limit the source or destination hosts and/or the ports but the HSRP data is still there.
like this access-list 150 permit tcp any any eq 1023 access-list 150 deny udp any any eq 1985(code)
I'm troubleshooting one way audio with our anyconnect phones.I think it is a routing issue.typically I wouldnt run debug ip packet detail on a production router, however I just found out that you can use acl's to specify the traffic to be debugged.
R1(config)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1 R1(config)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1 R1(config)#end R1#debug ip packet 199 detail IP packet debugging is on (detailed) for access list 199
The use of debug commands requires the allocation of system resources like memory and processing power and in extreme situations can cause a heavily-loaded system to stall. Use debug commands with care. Use an ACL in order to selectively define the traffic that needs to be examined to reduce the impact of the debug command. Such a configuration does not filter any packets.
I'm trying to troubleshoot a random packet drop issue for an IPSec tunnel between two VTIs. For over a month, we didn't see any issue, and starting today, we have up to 30% packet loss across an IPSec tunnel.
After some analysis, I concluded that the packet loss happens somewhere on the path from the uc520 to the 2921. Packet counts show up correctly on the uc520 physical egress interface, but the packet count is low on the ingress interface on the 2921.
Pings outside the tunnel along the same path are fine.
I also cleared the tunnels on both ends and after they reestablished, the issue was still present.
Any pointers on finding where the packets get lost?
rr-hq-2921#ping 10.1.13.1 source g0/1 rep 100 Type escape sequence to abort. Sending 100, 100-byte ICMP Echos to 10.1.13.1, timeout is 2 seconds:
i have 3 access-list configured IN | Out on my Border router (MARTIAN) ,i have to look which one block some of the traffic passing through ,for that matter i have enabled the below commands on my ISR 2900: with nothing output.
how to debug an ACL I've created on a 4404 WLC, specifically I want to monitor what packets are being denied by the ACL as something that should be working isn't
I've created an explicit deny statement at the end of the ACL and verified that the counter increases each time I try the problem software update.
What I can't work out is how to get the WLC to tell me what packets are being denied by the explicit deny statement, all I can find are 'show acl' commands which just give me the counts.
The equivalent on a router would be debug ip packet acl and adding the log keyword onto an ACE. I suppose I could configure a SPAN session on the WLC uplink to the switch but that seems overkill?
Iam fairly new to Cisco IOS and am having trouble getting an IPSEC tunnel to come up between 2 cisco 881-s. I have entered both debug crypto isakmp and debug crypto verbose but when I try to ping an internal IP at the other location through my VLAN1 interface no debugging info comes up.
Also my ACL-s for the crypto maps show no activity. I have tried many things so my configuration files are starting to get really messy.
I'm attempting to debug an ipsec tunnel on an ASA 5510 (8.4(3)) and when I turn on `debug crypto ipsec` and then execute `logging monitor` I get an constant stream of TCP debugging events, is it possible to only view ipsec messages?
Debug is not showing up on the console. I have configured logging console. My older switches, if an interface goes down or is brought up, it shows up on the console, but not on the new 4507s.
WS-C4507R-E cat4500e-ipbase-mz.122-53.SG2.bin TG-4507#sh loggingSyslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator.
Any way of narrowing down a degub for a peer address only? For example, I currently run 'debug crypto isakmp 127' which captures everything, but can I run the same dVPN debug for peer address 1.1.1.1?I know you can run 'sh crypto ipsec sa peer 1.1.1.1'.We're using an ASA5520 (8.4.2).
I am quite new to wireless side and had a small Q regarding watching debug output while i am ssh to the WLC? I tried the other day and did not see any messages, now this could be for the reason that nothing triggered or perhaps it needs something like terminal monitor?? i couldnt find any such command. my WLC is 5508 running 7.3 version.
I have a 2600 with a PRI card, when I try to do an isdn test call int s1/0:23 ######### the debug constantly comes back with "Cause i = 0x83E020 - Mandatory information element missing" Vendor states he doesn't see the SDN 'flag' coming through. I have both the isdn nsf-service, and the dialer map configured to use a class with the outgoing sdn command.
I use a C892 router with the IOS c890-universalk9-mz.152-1.T.bin. I just ran the command "debug ip packet 151 detail" and then the router stopped to work because it was overloaded. The ACL151 I used is as follow:
Extended IP access list 151 10 permit ip host 10.1.1.1 host 91.1.1.1 In the syslog then I got hundred of messages from IPSec: Jan 11 09:43:35.677: IP: s=10.80.10.254, d=10.64.19.99, pak 8A7453CC consumed in output feature , packet consumed, IPSec: to crypto engine(70), rtype 1, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
[code]....
For me it seems just like that this ACL is not applied and that I have a debug then for the whole traffic.
There is a plenty of tunnels ended and it works.But i have one tunnel, which doesn't work.I tried turn on "debug crypto isakmp" and it show this: RECV PACKET from 10.200.79.161 ISAKMP Header. [code]
So there is problem with IPSEC and with no matching SA, but i don't know which one.Then i try to turn on "debug crypto ipsec 255" but it displays nothing. [code]
I have a Cisco 857 which seems to be dropping connection on its public interface.I would like to see the logs of the ppp or something which may identify the problem of why the device has lots its connection.
I know what you can setup logs for a specific IP, but it is possible to setup logs for debug messages?Also what other logs would identify the problem?
What would cause debug output to not show on a remote session via telnet connection where you've enabled terminal monitor?
The reason I ask is I was working with a client and we were debugging WCCP. I ran the debug ip wccp packets and events commands, then entered terminal monitor. After this, we saw nothing. We should have at least seen particular WCCP-related packets because we saw the necessary cluster view was established which can't be done without the exchange of these packets.
Can having syslog (logging) configured cause the issue? Did I use the command incorrectly?
I've created a BVI2 where I bridged dot11 0.2 and vlan2 in order to have wired and wireless clients in the same vlan.Some wired client are not reachable from the lan. Wireless clients have no pbl in reaching each other.Monitoring a MAC address that is supposed to be behind the FA2 I have noticed that it moves to vlan2 when in fact it should be behind the FA2.Of course when "show mac-address-table" says it is behind Fa2 the ping to that MAC address works whereas when the TCAM reports it is behind vlan2 it doesn't. Once the MAC address is behind the vlan2 if I clear the mac-address-table and that mac-address is still put behinf Fa2 then the pings works again, sometime I have to perform twice the clear command before the MAC address goes back to the right location.I'd like to understand why the router moves that MAC address from Fa2 to vlan2 and that's the reason for my question in the subject.I don't have any problems for port Fa0 and Fa1."Show int fa2" doesn't show any problem/errors or the likes.BTW even if I force that MAC address to be statically behind FA2 the ping works fine but then stops and if I do "show mac-add" the static entry for it is still there... so looks like there us something that overrides that static entry. If clear everything and I have the mac-address be behind Fa2 then everything starts to work again. I used Fa3 instead of Fa2 and I get the same results.
I have strange problem with 1800 router , I can't see any debug messaging , the ping from PC to this router is Ok , but no icmp debug appears , even I enable "debug ip icmp " the version of router is : C181X Software (C181X-ADVENTERPRISEK9-M), Version 12.4(6)T6
We are experiencing intermittent issues with the IPS on our ASA5585 vs 8.4(2). Probably something with the dataplane. So I want to keep debug cplane 255 activated and logged with log debug-trace setting to syslog server. But when session times out the debug command is cleared so the output stops. Since it is a intermittent issue I want to keep debug activated...Totally different behaviour then with routers which keeps it activated. how to keep debug activated on a ASA.
I have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
I am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
My Nexus is a 5548-UP model, NX-OS version : 5.1(3)N2(1b)
I try to debug an OSPF and an ICMP problem using the debug ip ospf command and the debug icmp command but not output appear on the terminal. As the switch is remote, I entered the terminal monitor command of course.
SG01NX01# terminal monitor SG01NX01# debug ip ospf 1 packets SG01NX01# show debug
we have made migration from CISCO 2821 to ASR1002-X.Cisco router is used as LNS for our ADSL links, using L2TP protocol. On 2821, everything worked fine. Migrating with same config on ASR1002-X, everything worked except L2P sessions.
We wanted to debug but no debug is displayed about L2TP or PPP in console with commands :
We don't understand why no debug log ??? Is it a bug in IOS XE ?show vpdn session all and show vpdn tunnel all gave "%No active L2TP tunnels"
Here our configuration :
sh ver Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 1 5.2(4)S1, RELEASE SOFTWARE (fc3) Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc. Compiled Sat 06-Oct-12 13:03 by mcpre
I'm testing debug spanning-tree functions in a lab, hardware is Cisco 6509 with SUP-720-3B and WS-X6748-SFP, IOS is 12.2.33.SXJ. It's a root in some vlan's, stp mode is rapid-pvst.I wanted to see how spanning-tree is working (STP packets dump, etc.), and entered following commands on 6509: [code]
Then, I turned the "debug spanning-tree all" mode on. Now, I expect to see BPDU packets from Cisco, and other spanning tree events in logs on syslog server, or in log buffer, but I don't get anyting there. Except, there're some lines in log (they repeat very rare): [code]
I want talk BGP with ISP though 200Mb/s WAN link by using Cisco Router 2921; and in the near future WAN link will be upgraded to 1Gb/s. Does Cisco Router 2921 has enough performance to do this task?
