I have strange problem with 1800 router , I can't see any debug messaging , the ping from PC to this router is Ok , but no icmp debug appears , even I enable "debug ip icmp " the version of router is : C181X Software (C181X-ADVENTERPRISEK9-M), Version 12.4(6)T6
View 2 Replies
I have a message that appears when i run a debug on my switch :
Core1#pak 5884A9C consumed in input feature , packet consumed, MCI Check(63), rtype 0, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
I am new user of cisco router i can access the hardware and login in the account but the problem is if i use the command "enable" asking for a password, old I.T. personnel who setup this router already resign.
View 2 Replies View RelatedI've created a BVI2 where I bridged dot11 0.2 and vlan2 in order to have wired and wireless clients in the same vlan.Some wired client are not reachable from the lan. Wireless clients have no pbl in reaching each other.Monitoring a MAC address that is supposed to be behind the FA2 I have noticed that it moves to vlan2 when in fact it should be behind the FA2.Of course when "show mac-address-table" says it is behind Fa2 the ping to that MAC address works whereas when the TCAM reports it is behind vlan2 it doesn't. Once the MAC address is behind the vlan2 if I clear the mac-address-table and that mac-address is still put behinf Fa2 then the pings works again, sometime I have to perform twice the clear command before the MAC address goes back to the right location.I'd like to understand why the router moves that MAC address from Fa2 to vlan2 and that's the reason for my question in the subject.I don't have any problems for port Fa0 and Fa1."Show int fa2" doesn't show any problem/errors or the likes.BTW even if I force that MAC address to be statically behind FA2 the ping works fine but then stops and if I do "show mac-add" the static entry for it is still there... so looks like there us something that overrides that static entry. If clear everything and I have the mac-address be behind Fa2 then everything starts to work again. I used Fa3 instead of Fa2 and I get the same results.
IOS: c870-advipservicesk9-mz.151-3.T1.bin
what logging buffered 51200 debug do?i saw it on cisco 881 sec k9
View 1 Replies View RelatedI am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
View 4 Replies View RelatedMy Nexus is a 5548-UP model, NX-OS version : 5.1(3)N2(1b)
I try to debug an OSPF and an ICMP problem using the debug ip ospf command and the debug icmp command but not output appear on the terminal. As the switch is remote, I entered the terminal monitor command of course.
SG01NX01# terminal monitor
SG01NX01# debug ip ospf 1 packets
SG01NX01# show debug
[Code].....
What other command can be used to debug packets on a 3750 switch ?
View 2 Replies View RelatedI'm testing debug spanning-tree functions in a lab, hardware is Cisco 6509 with SUP-720-3B and WS-X6748-SFP, IOS is 12.2.33.SXJ. It's a root in some vlan's, stp mode is rapid-pvst.I wanted to see how spanning-tree is working (STP packets dump, etc.), and entered following commands on 6509: [code]
Then, I turned the "debug spanning-tree all" mode on. Now, I expect to see BPDU packets from Cisco, and other spanning tree events in logs on syslog server, or in log buffer, but I don't get anyting there. Except, there're some lines in log (they repeat very rare): [code]
I have aaa new model configured on a number of isr's(1800, 1900, 2900, 3800 etc). When i have aaa configured, the telnet logins use that authentication and not the password in the line vty portion. Is this by design. would disabling aaa enable both telnet and aaa authentications, essentially making it a dual login.
View 3 Replies View RelatedI have an 1800 isr that is running with port forwarding only. It is running a series of ip nat inside source static address port address port commands. It does not have an access list bound to the outside interface. This is working fine, but i am wondering if this is a security concern?
View 1 Replies View RelatedI would like to configure IP SLA with ICMP tracker. What is the minimum IOS & Feature required in cisco 1800 Router?
View 2 Replies View RelatedI've just started out playing with a Cisco 1800 router to gain some knowledge of Cisco devices before taking a CCNA. I also have a 2950 switch but will start with the router.
I'm using an Android phone as a wireless Internet access point. This issues IP addresses by DHCP in the 192.168.43.x range with 255.255.255.0 subnet.
Also I have a Linksys WRT54G router running DD-WRT firmware acting as a wireless bridge to the Android phone, and it has 4 LAN ports.
This bridge is up and running and I have successfully connected my laptop to the Linksys for testing and can use the Internet provided by the phone.
Connected to the Linksys is a Cisco 1800 router. Connected to the router is my Citrix XenServer PC and a NAS box.
The XenServer and NAS are on another network 07.05.19.x range with 255.0.0.0 subnet using their own static IPs. One of the virtual clients on the XenServer will be a DHCP server to service other virtual clients. All still in the 07.05.19.x range.
Basically I want the devices on the 07.05.19.x IP range to be able to use the Internet gateway at 192.168.43.1 to access the Internet.
How would I set up my 1800 to achieve this?
Also, am I right in understanding that the 1800 will ignore DHCP leases from the Android phone due to it being a Layer 3 device.
I setup a GRE tunnel between two cisco 1800 & 1900 routers. I can't received multicast.
Here is a copy of my configs:
R3#Building configuration...
Current configuration : 1238 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname R3!boot-start-markerboot-end-marker!logging message-counter syslog!no aaa new-modeldot11 syslogip source-route!ip cefip multicast-routing no ipv6 cef!multilink bundle-name authenticated!archivelog config hidekeys! interface Loopback0ip address 10.0.0.3 255.255.255.255!interface Tunnel0ip address 192.168.24.2 255.255.255.252ip pim sparse-modetunnel source Loopback0tunnel destination 10.0.0.1!interface FastEthernet0/0ip address 10.0.3.1 255.255.255.0ip pim sparse-modeduplex autospeed auto!interface FastEthernet0/1ip address 192.168.23.2 255.255.255.252ip pim sparse-modeduplex autospeed auto!interface Serial0/0/0no ip addressshutdownno fair-queueclock rate 2000000! router eigrp 1network 10.0.0.3 0.0.0.0network 10.0.3.1 0.0.0.0network 192.168.23.2 0.0.0.0no auto-summary!ip forward-protocol ndno ip http serverno ip http secure-server!control-plane!line con 0line aux 0line vty 0 4exec-timeout 5 0privilege level 15no login!scheduler allocate 20000 1000end
[code]....
When i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies View RelatedI don't know much about routers, but lately I've been playing around with router configuration and getting better but I am kind of stuck now.
The scenario is this.
I have 3 ip net from the ISP:
178.249.51.0/255.255.255.248 Gateway 178.249.51.1
178.249.51.8/255.255.255.248 Gateway 178.249.51.9
178.249.51.16/255.255.255.248 Gateway 178.249.51.17
[Code]....
I am also wondering - when we get more public IP net from the ISP, is this the correct way to do it?
I have this system: IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1
An error appear in console (many times in one minute):
Jan 3 16:25:37: %LINK-3-BADMACREG: Interface StackPort1, non-existent MACADDR registry for link 0
-Process= "<interrupt level>", ipl= 4
-Traceback= 20A364 187F04 58D6FC 58B950 2D7CE0 2E00C8 2E2BEC 2E2F24 2B0BF8
What is the problem? What is the solution?
I'm using "WS-C4948(12.2(54)SG)+PWR-C49-300AC/2". The following message are logged in the system log, but it was to check the status with the show command and status LED, but there was no abnormality. I thought the power supply has failed, but I seem different.
040861: Apr 27 07:00:50: %C4K_IOSMODPORTMAN-4-POWERSUPPLYBAD: Power supply 1 has failed or been turned off
040862: Apr 27 07:00:50: %C4K_IOSMODPORTMAN-4-POWERSUPPLYFANBAD: Fan of power supply 1 has failed
I checked.>> #show environment alarm no alarm
#show environment status power supply
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C49-300AC AC 300W good good n.a.
PS2 PWR-C49-300AC AC 300W good good n.a.
All Status LEDs are green.
I've taken 2 4507's fresh out of the box running CAT4500E-ENTSERVICESK9-MZ.122-53.SG2.BIN which was upgraded from CAT4500E-IPBASEK9-MZ.122-53.SG2.BIN
I'm getting constant %C4K_S2W-4-WRITECALENDARERR: Calendar write operation Failed errors on the console. I was also getting them on the original IOS version.
Anything I've seen say's to ignore them but their very frequent filling up the logs.
There's very little return on google and no bugs to report on Cisco?
I have in logs following error message:
%DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module 1
Has failed test SpineControlBus 20 times on device Power Mgmt Bus on slot 10 due to error Spine control test failed error number 0x00000002.
I get a unclear log entry in a VSS system.
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
[code]....
Have a small stack of two 3750 routers. Get the following error message every few secounds:
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state UP
Now I replaced the stacking cables but no joy. It was ok for an hr or so but then the error messages popped up again. Also random links on this stack back to access layer user switches have been going up and down randomly. So I have decided to take the next step and upgrade the IOS.
Although when I try and copy a new IOS I get the following error:
%Error writing flash:/c3750-ipservicesk9-mz.122-55.SE6.bin (No space left on device)
Seems this image is 130MB while the image that is currently on it is 74MB and free space is 54MB. How do I get the image onto the router? If I delete the current image from flash will that cause the router to stop functioning?
Also I noticed there seems to be more than one flash directory. See below:
copy tftp: ?
flash1: Copy to flash1: file system
flash2: Copy to flash2: file system
flash: Copy to flash: file system
null: Copy to null: file system
nvram: Copy to nvram: file system
running-config Update (merge with) current system configuration
startup-config Copy to startup configuration
system: Copy to system: file system
vb: Copy to vb: file system
The current router image seems to be in flash1 and flash 2 also. Could I delete the image from flash1. Upload it there and then boot the router from flash1?
For a week now, one of my Cisco 3945 routers displays, from time to time, the following message in its log:
2012-07-16T14:12:43.852017+00:00 cb00-r103 220: [syslog@9 s_sn="59"]: Jul 16 16:12:42 MEST: %SYS-2-INTSCHED: 'may_suspend' at level 4 -Process= "OSPF-100 Hello", ipl= 4, pid= 320
2012-07-16T14:12:43.852017+00:00 cb00-r103 221: [syslog@9 s_sn="60"]: -Traceback= 15CB073z 9081B7z 2851571z 11B7582z 11C275Ez 11C2906z 11C03E3z 1B907B5z 1B9064Cz 1BA5737z 172047Fz 47FFDCz 4D2EEDFz 4D2ED71z 4D2EA2Bz 4D30097z
2012-07-16T15:06:11.686817+00:00 cb00-r103 222: [syslog@9 s_sn="61"]: Jul 16 17:06:10 MEST: %SYS-2-INTSCHED: 'may_suspend' at level 4 -Process= "OSPF-100 Hello", ipl= 4, pid= 320
2012-07-16T15:06:11.686817+00:00 cb00-r103 223: [syslog@9 s_sn="62"]: -Traceback= 15CB073z 9081B7z 2851571z 11B7582z 11C275Ez 11C2906z 11C03E3z 1B907B5z 1B9064Cz 1BA5737z 172047Fz 47FFDCz 4D2EEDFz 4D2ED71z 4D2EA2Bz 4D30097z
[code]....
It never happened before and the configuration did not change. The only thing that happened, the WAN connection (point-to-point to a Cisco 3845) went down and the router rebooted while the WAN was down. When the WAN came up again, everything went fine, until about an hour later and the first occurrence of this mentioned log.This 3945 does establish an IPSec tunnel with its peer (the 3845) and all the traffic, including OSPF, is going through the tunnel.
my MSFC2 sent this strange log message. %DATACORRUPTION-SP-1-DATAINCONSISTENCY: copy error, The error message decoder tool says: "NOT FOUND". The level is "alert".
View 8 Replies View Relatedwhat is causing " Gigabit port is restricted to full duplex" while trying to hard code speed/duplex on a 4507 switch port?
View 3 Replies View RelatedWe are running a small network business and as funs of ciscos we own a some of the 4948s.We are facing an issue with couple of them as we get the below error message
C4K_CHASSIS-3-INSUFFICIENTPOWERSUPPLIESDETECTED:Insufficient power
supplies present for specified configuration
First thought to replace the power supply didn't actually work as we did that with no result.Power consumption is not an issue as well because all other 4948s work fine with 1 power supply (forgot to mention is 1 power supply in all of them).
I recently upgraded my network to have two 3750x core, one interface on the Cisco is connecting to a Net gear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
003396: Sep 17 01:46:16.328: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003397: Sep 17 01:46:19.843: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003400: Sep 17 01:49:58.769: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/17, changed state to down
[Code] .....
After my research i think this is a looping issue but I'm unsure how to address it.
I have a Cisco 2800 series and it doesn't boot, only shows this message in the CLI>
Bad RAM at location 0xA0000304: wrote 0xA0000304, read 0xA0000004
What means this? I have to change the RAM?
logging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 Replies View RelatedI am receiving the following error message on a Cisco 3750 switch stack. Need troubleshooting this error message.
00:03:13: %SW_MATM-4-MACFLAP_NOTIF: Host 00d0.7400.2730 in vlan 600 is flapping between port Gi2/0/3 and port Gi2/0/2
I recently upgraded a few 2960 switches to 15.0(1)SE, and while they are working fine, I did notice a strange syslog message upon boot-up that wasn't previously there. [code] I did some cursory searching via google but nothing useful presented itself.
View 7 Replies View RelatedI have a stack of Catalyst 3750E switches.
IOS image :c3750e-ipbasek9-mz.122-55.SE3.bin
I have been seeing multiple occurance of the below message in the switch logs.
"Failed to send hrpc non blocking message"
I could not find a relevant reference for this message in the Cisco.com.
I am receiving this error after connecting a copper adapter on a GBIC blade in a 6509. Here are the results from the show Interface. I am waiting to confirm the device on the other side settings but as far as I see I get UP and Up for protocol and line respectively.
GigabitEthernet2/11 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0009.11e4.f3ce (bia 0009.11e4.f3ce)
Description: RCPBSDEV
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]....
