I have a stack of Catalyst 3750E switches.
IOS image :c3750e-ipbasek9-mz.122-55.SE3.bin
I have been seeing multiple occurance of the below message in the switch logs.
"Failed to send hrpc non blocking message"
I could not find a relevant reference for this message in the Cisco.com.
I have a pair of 3750E-24PD-S stacked together, it seems after stacked together the stacked switch always flood the console screen with these messages which are not true: [code] Switch-2 is the stack member, Switch-1 is the stack master. The RPS fan failed refers to RPS2300 or the internal power supply of 3750E? Even when I turned on the RPS2300 the stacked switch still display the messages. Also I have two RPS2300 serving stack master and stack member respectively both RPS2300 were switched off why the messages only refer to Switch-2 and not Switch-1? [code]
View 1 Replies View RelatedI need to use cisco 3750E switch on core. I want to know whether BGP is supported on this model or not?Currently i have c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin" preinstalled. and i checked BGP is not supported on this IOS image.
View 7 Replies View Relatedhow to send message to the other computer with lan connection using command prompt?
View 1 Replies View RelatedQuick question here. Using 3750E series switches with multiple VLANS configured. These switches serve as our 'core'. I have SVIs configured for the different VLANs and add inbound ACLs in each of the SVIs to control traffic between VLANS. This switch also terminates a P2P Ethernet link which connects to our Colo facility. The port used for this is configured as an L3 port. I noticed today that I was able to send traffic across this L3 link that I thought should have been blocked by an ACL I had in place but it wasn't. So the traffic flowed from a port in say VLAN 20 across this L3 link (assigned with an IP address). Would this traffic flow not cause traffic to be checked against an ACL applied in the inbound direction on the SVI of VLAN 20 (int vlan 20)? Traffic does get checked when routing between SVIs. Why would it not get checked when routing between SVI and L3 interface?
View 2 Replies View RelatedI am in the process of upgrading our network switches and wondering if the .lic file will work with the new software or if I have to rehost for the move to 15.0. Its a remote site and I would like to get some solid info before I pull the trigger.
Also which IOS should I be upgrading to?
c3750e-ipbasek9-mz.150-2.SE.bin
or
c3750e-universalk9-mz.150-2.SE.bin
[Code].....
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedI'm running a home network with 3 computers via a linksys router attached to a westell modem. Is there a local network messaging system I can use to pop a message on a screen to one of the other computers? Can I use DOS?
View 1 Replies View Relatedhave 2 3750's one is an 3750E the other one is a G... Since they are 2 different versions Do I need to correct ios for each for example my 3750E switch i would have
IP BASE
c3750e-ipbasek9-mz.122-53.SE2.bin and for my 3750G switch should i use
IP BASE
c3750-ipbasek9-mz.122-53.SE2.bin
Which would be 2 separate images
Can I get a stack cable longer then 3m?
View 1 Replies View RelatedServer Error: 550 emails blocked from send.
View 1 Replies View RelatedWe're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
I am seeing on my 3750E series switches (WS-C3750E-48TD). I have multiple VLANs configured on here, one which is used as a 'workstation' VLAN. I have an inbound ACL applied to the VLAN interface *(int vlan 50 to be exact). This list is admittedly long at roughly 6000 ACE's. Now I just recently installed these switches as they replaced some 4507R switches which we moved to our new centralized DC. Here is the issue I am having. This same ACL was applied to the same VLAN interface on the 4507s when they were doing the work of the 3750s. What I used to be able to do was actually edit the ACL by removing it with no ip access-list extended WS-In and then followed up by the ip access-list extended WS-In ......and the lines I wanted in the ACL. I know I could use the line numbers to edit the ACL but this worked OK for me. When I would do this on the 4507R, the ACL was still applied to the interface but traffic never seemed affected by the removal and re-adding of the ACL. I did this by copying and pasting the ACL into a terminal window. It seemed as though on the 4507 the ACL was not compiled until the entire thing was in loaded in and therefore traffic was not processed by the ACL until the load was done
View 3 Replies View RelatedI have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies View Relatedwhat is difference between Cisco catalyst 3750e 48 and SF300-48p.
View 3 Replies View Relatedcan I make the stacking of these two switches WS-C3750E-48PD-SF and WS-C3750X-48PF-L. Both have universal IOS.
View 11 Replies View RelatedI have 3750E swiches with IOS v. 12.2(55)SE3. Couple servers connect to ths switch, after ping of IP this servers I can see mac addresses in mac address table.
For instance:
sw1#show mac address-table vlan 20
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports(code)
---- ----------- -------- -----
When ip generate traffic to this server this mac address appear in table again on shot time (less than 10 seconds).
I had a lot of problems with TCAM table in the past and made changes in SDM ended whit that. But now want to be proactive and anticipate the problems in my TCAM table.
If the my template is "default desktop" they support a number of indirect IPv4 routes of 2k. I wanna know automatically by my management tools if this number reaches 1.9k.
That way I can take corrective actions before the problems starts on my network.
I have a RVS4000 connected to my cable modem which I use as my gateway, the IP address of the RVS is 192.168.3.254
I have a 2811 with 3 subinterfaces of which I can ping all of them from my PC which at the minute is in VLAN 1, the only network that can connect to the outside world is VLAN 1, how can I enable the other 2 vlans to connect to the internet?
My set-up details are
Router
interface FastEthernet0/0.1
description *** Data Network***
encapsulation dot1Q 1 native
[Code]....
After I added the 3rd 3750E to my stack on Sunday I can no longer save my configs with 'copy run start' or 'write mem':
#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
nv_done: unable to open "flash:/config.text.new"
nv_done: unable to open "flash:/private-config.text.new"
nv_done: unable to open "flash:/multiple-fs.new"[OK]
[code]....
my flash seems to have plenty of space:
57409536 bytes total (24203776 bytes free)
Cisco works LMS 4 is very complicated tool for me and it is very hard to configure any cisco device what I need to monitor.Currently I have 3750-X configured, properly discovered and added to DCR. I would like to receive SMTP messages(mail) from LMS if some event occurs. For example when link UPDOWN occurs or when LOGIN_FAILED occurs and so on. I tried to configure it in Monitor > Monitoring Tools > Fault Monito, but without siccess. LMS tell me that there are no devices available.How can I configure some notification so it is able to send me message via smtp?
View 0 Replies View Relatednet send command not working. Even after starting messenger. Error : The Message Alias could not be found on the network
View 3 Replies View RelatedWe tested a QoS in a Cisco 3750E, IOS: 12.2(58)SE2.Voice traffice in the correct Q without any problem, but all the others traffic the Defualt Q (0), tried to capture the traffic and tcp/udp port are correct.Any thing wrong with my ACL or DSCP - CoS?? ( that ACL works fin on 4500 and 6500) [code]
View 3 Replies View RelatedI am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
View 4 Replies View RelatedI have a device which will be sending voice and data packets and is able to mark the packets with DSCP values. Voice, 18 and Data 42.If this was a straight through network, I'd be clear on how to handle this, but.....I will be putting this traffic into a VLAN to isolate it from some other traffic on the network. What is the best way to prioritize this traffic inside the VLAN? Will the Cisco switch look at and respect the DSCP values inside the VLAN and prioritize accordingly inside the VLAN? Or, do I need to do some sort of DSCP to 802.1p mapping? Another option I would be fine with would be mapping the DSCP values for voice and data to two different VLANs and then giving the voice VLAN priority over the data VLAN .... I'm using 3750E switches.
View 7 Replies View RelatedWhat is meaning backup on HSRP statas?There are 5 vlans.The other four vlans aren't backup status.Only one of five vlans display messeages. When I reload Catalyst3750E-1,debug log. [code]
View 6 Replies View RelatedCan we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies View Related9x3750E stacked switch (WS-C3750E-48PD-SF0) (15.0(1)SE2
C3750E-UNIVERSALK9-M)
2x10Gbe uplinks from EMC NAS
At a basic level, we have found that the 10Gbe uplinks have slow read performance with or without a port-channel configured (2-3 minutes for a 700MB file to desktop from the NAS) We switched back to testing a 1Gbe and the read speed is normal. Another anomaly is Win7 / 2008 machines read speed is fine from the NAS while the 10Gbe uplinks are in production?!
Write speed is great on 10Gbe. Only read speed is affected!! the switch is not reporting anything abnormal. We looked at SMB/SMB2 as another possible cause...
mls qos is enabled on the switch but not sure if this is affecting performance.
Is the ANY config that I need to carry out on the interfaces to get the read speed working as it should for both Win7 and WinXP. (MTU is 1500 throughout the enterprise, NAS included).
I have installed and configured 2 new WS-3750E-24TD in the last 30 days, that have software version 12.5(50)SE2-universalk9, on our flat Development LAN (currently 7 existing WS-3750E-24TD with 12.5(35)SE2-universal)The new switches have shutdown, 1 has shutdown twice and I just had the other one shutdown on the weekend, all the status lights on the left are lit up but no port lights are on, I am not able to console in to the switch all I can do is cycle power. I am planning on upgrading all switches to the latest software release universalk9-mz.150-1SE
could this problem be a version incompatibillity between the switches?
We have many 3750E's and need to use Finisar X2 modules FTLX8541E2. After 15.0(1) IOS upgrade the 3750's now recognize the Cisco part X2-10GB-LRM's, but will not recognize our Finisar modules.
View 1 Replies View RelatedAccording to the following Cisco webpage, cross-stack 10-Gigabit EtherChannel is possible on the 3750 with up to two 10-Gigabit modules, using LACP: url...However, the webpage doesn't confirm if this functionality is restricted to a particular 3750 model, such as 3750E, or if it applies to all models. It also doesn't specify any particular IOS feature set. I've tried Cisco Software Advisor but it doesn't list this feature on either the 3750E or 3750-X. This is possible on the 2960-S switches (i.e. cross-stack 10gig EtherChannel)?
View 23 Replies View RelatedIs there a way to use the "no switchport command to enable routing on a port and yet sequester it from traffic on other vlans within the switch?
The switch in question is a 3750E
I need to connect one sw3750E with two 3750X , with Uplinks at 10 GBps. My doubt is the next:
Switch 3750E has two TwinGig Adapter Converting 10 Gigabit Ethernet X2, phisically each twinGig adapter has 2 slots for SFP modules. Can I install sfp+ If I want to use copper for Uplink at 10 Gbps, I just need to install one SFP-H10GB-CU5M transceiver ???? the other SFP slot is disabled automatically?
in the other side 3750X in order to support copper at 10 Gbps a C3KX-NM-10G network module is considered, this will be connected to SW3750E by means of SFP-H10GB-CU5M.
The second 3750X will be connected to second twinGig Adapter of 3750E using another SFP-H10GB-CU5M transceiver.