Cisco :: 3750X - Configure Some Notification To Send Message Via SMTP
Mar 12, 2012
Cisco works LMS 4 is very complicated tool for me and it is very hard to configure any cisco device what I need to monitor.Currently I have 3750-X configured, properly discovered and added to DCR. I would like to receive SMTP messages(mail) from LMS if some event occurs. For example when link UPDOWN occurs or when LOGIN_FAILED occurs and so on. I tried to configure it in Monitor > Monitoring Tools > Fault Monito, but without siccess. LMS tell me that there are no devices available.How can I configure some notification so it is able to send me message via smtp?
I am trying to find a way of sending a notification message to computers that have been "woken up" by Wake On LAN, so that the user knows there computer is now up.
Motion detection is setup - and I can see in the log and on the Live Video "Motion Trigger Indicator" that this part is working. I can also send test-emails, so the smtp is set up correct. In the Event Setup I have a valid server and a motion triggered event with the status ON. But no emails are sent . In the log there is also no indication of the server trying. Am I missing something - or is this not working for anybody?
And - there is no firmware beyond 1.0 for this model as far as I can see.
P.S. I am using a Gmail account for smtp, port 587 and using startTLS to send with,
I sold a rv220w to a customer. I've configured it but it seems that the router doesn't allow anonymous smtp. I've configured outlook on a computer with authentification request and it's working fine.
There is a software on a computer that I'm unable to change the authentification and it's not working ( Not able to send message ) I've search in the router and I've disabled these rule : "Block Anonymous ICMP Messages".
My coworker told me that port 25 is closed in office , so I can't use [URL] as SMTP Server and to ask for direct line instead of 25.I don't know how to use/setup direct line
I'm running a home network with 3 computers via a linksys router attached to a westell modem. Is there a local network messaging system I can use to pop a message on a screen to one of the other computers? Can I use DOS?
Is there a way to configure an email notification for a specific authentication failure? Specifically, I'd like to see if I can have an email notifcation sent to me when failure reason is "13017 Received TACACS+ packet from unknown Network Device or AAA Client".
I have a stack of 3750x switches running 15.0 (2) SE2 IOS. When I reload the switch stack, I am seeing the following message in the logs: IPv6 user port trust TCAM write failed.
I need to configure my ASA 5520 version 7.3 firewall to translate our SMTP server residing in local LAN to use different IP address from the outside interface which is used by all other computers to access Internet. Under NAT section, I have NATted this internal SMTP server with different IP address(eg x.x.x.1) and also translated the remaining IP addresses in the LAN to the outside interface(eg x.x.x.2)
my problem is, Whenever i check the header for message coming from the smtp server it shows that, the SMTP server is also translated by using the same outside interface public ip address(i.e x.x.x.2) which is used by other client machine to access internet instead of the x.x.x.1. How I can get my SMTP server to use separate IP and avoid to be blacklisted by some domain.
I need to configure my ASA 5520 version 7.3 firewall to translate our SMTP server residing in local LAN to use different IP address from the outside interface which is used by all other computers to access Internet.
Under NAT section, i have NATted this internal SMTP server with different IP address(eg x.x.x.1) and also translated the remaining IP addresses in the LAN to the outside interface(eg x.x.x.2)
my problem is, Whenever i check the header for message coming from the smtp server it shows that, the SMTP server is also translated by using the same outside interface public ip address(i.e x.x.x.2) which is used by other client machine to access internet instead of the x.x.x.1.
how i can get my SMTP server to use separate IP and avoid to be blacklisted by some domain.
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
I want my computer to send a SMS txt message to my cell phone when a certain text message get written to by another program. Purpose is to alert to a certain action, an event, has occured that the program is monitoring.The cell phone uses Verizon as the carrier.
I have 2 Cisco 5508 Wireless LAN Controllers.They are NOT connected to a WCS.Is there a way to configure the 5508's to send email notifications when an AP drops off line?Is not is this functionality available with either a WCS or new NCS?
I have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch: Vlan 100 172.17.1 Vlan 200 172.18.1 Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
I have a one 3750x switch and 10 nos of 2950 switch, i want to configuration etherchanel between 3750 to 2950, for that i need 10 nos of etherchanel interface(virtual), but the 2950 switch support maximum of 6 nos of etherchanel port?
I went to configure RADIUS on my 3750X with IOS 15, and lo and behold it is not where it used to be. Did it get moved somewhere else that I can't seem to find very easily?
Possible to configure multichassis port-channel between a VSS and 3750X (Port-channel not in the same switch on the 3750X stack). I got it using LACP but I need Pagp to get VSL redundancy “dual-active detection pagp trust channel-group 1”. I am using the last VSS IOS version 15.0(1)SY. I can’t get the option “switch 1 preempt”, has it changed with other option?
I have two stacks 3750X on two different sites with two links L_2_L, and I want to configure the port channel to aggregate the two links.
Site A Site B 3750X -A1 --------------------------------------( )--------------------------------------- 3750X -B1 ( L-2-L ) 3750X -A2 --------------------------------------( )--------------------------------------- 3750X -B2
Below the configuration that I have put the two stacks.
site A interface Port-channel5 description Etherchannel group entre le stack 3750X-A et Switch Lan_2_Lan switchport trunk encapsulation dot1q switchport trunk allowed vlan 11,12,999 switchport mode trunk switchport nonegotiate speed 100
But the problem is only one link is Bundeled in channel group, see below
Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 5 Po5(SU) LACP Gi1/0/15(I) Gi2/0/15(P)
I have not used the ACS5.1 yet so watch out for the easy questions
1) Is it possible to generate report for the users who are inactive for say last 30 days? Customer is looking to audit these users to see if they really need access to any device.
2) Are there any known issues while assigning the priviligaes level to users. In current implementation of this customer users are always logged into priv 1 though they are assigning the priv level of 5. I understand with ACS 4.x we can enable the exec process and assign the priv under user/group policy. What are the configurations that customer might be possiby missing in this case?
3) Is there any SNMP or other notification available in ACS 5.1 where admin can be notified at the time a particulat set of user logs in.
I want to configure E-mail fault notification in LMS 4.0. So Where i will configure E-mail settings like username, password, mail server IP address in LMS. We are using e-mail service hosted in gmail. Through this mail service ca we able to use email notification.?
Have a setup for Cisco LMS3.2.1 which is a recent upgrade, also RME 4.3.2 and CM 5.2.2. Is it possible for the DFM to generate alerts such as email notification to user defined group (subnet grouped). These alerts should be critical in in nature.
I'm needing to be able to send e-mail nofigication when one of our network devices isn't able to be access. I have looked at the DFM configuration but I'm a little confused to how to set this up so that we don't get inundated with to many e-mails.
